Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tews Technologies TAMC900-A1
Summary of Contents for Tews Technologies TAMC900-A1
-
Page 1: User Manual
The Embedded I/O Compan y TAMC900-A1 Signal Conditioning Adapter for TAMC900 Version 1.0 User Manual Issue 1.0.2 November 2010 TEWS TECHNOLOGIES GmbH Am Bahnhof 7 25469 Halstenbek, Germany Phone: +49 (0) 4101 4058 0 Fax: +49 (0) 4101 4058 19 e-mail: info@tews.com... - Page 2 Gain = 1, Full-Size Front Panel, RoHS compliant reserves the right to change the product described in this document at any time without notice. TEWS TECHNOLOGIES GmbH is not liable for any damage arising out of the application or use of the device described herein.
- Page 3 Issue Description Date Initial Issue April 2008 1.0.1 - New Issue notation February 2010 - General Revision 1.0.2 Full-Size Front Panel added November 2010 TAMC900-A1 User Manual Issue 1.0.2 Page 3 of 17...
-
Page 4: Table Of Contents
4.2 Single Ended Signal Source ......................10 CLOCK ........................11 TRIGGER........................12 PIN ASSIGNMENT ....................13 7.1 Overview ............................13 7.2 Clock Connector ...........................14 7.3 Trigger Connector.........................14 7.4 Analog-In Connector........................15 7.5 SiCA Connector..........................15 TAMC900-A1 User Manual Issue 1.0.2 Page 4 of 17... - Page 5 List of Figures FIGURE 1-1 : BLOCK DIAGRAM TAMC900-A1....................6 FIGURE 4-1 : ANALOG INPUT BLOCK DIAGRAM..................9 FIGURE 4-2 : SINGLE ENDED SIGNAL SOURCE ..................10 FIGURE 4-3 : SINGLE ENDED SIGNAL SOURCE WITH IMPEDANCE MATCHING ........10 FIGURE 7-1 : CONNECTOR OVERVIEW ......................13 FIGURE 7-2 : PIN LOCATIONS ANALOG-IN CONNECTOR.................15...
-
Page 6: Product Description
1 Product Description The TAMC900-A1 is a simple Signal Conditioning Adapter (SiCA) providing I/O-connectors for the analog inputs, clock and trigger inputs and the analog signal conditioning. All inputs are differential. The signal conditioning consists of a differential amplifier with gain=1 and a low pass filter to suppress high frequency noise. -
Page 7: Technical Specification
If FIT rates are not available, MIL-HDBK-217F and MIL-HDBK-217F Notice 2 formulas are used for FIT rate calculation. 5 – 95 % non-condensing Humidity 50 g Weight Table 2-1 : Technical Specification TAMC900-A1 User Manual Issue 1.0.2 Page 7 of 17... -
Page 8: Handling And Operating Instructions
3 Handling and Operating Instructions 3.1 ESD Protection The TAMC900-A1 is sensitive to static electricity. Packing, unpacking and all other handling of the TAMC900-A1 has to be done in an ESD/EOS protected area. 3.2 Maximum Input Voltage The maximum input voltage of the Clock and Trigger inputs is 2.5 Volt. -
Page 9: Analog Inputs
4 Analog Inputs The TAMC900-A1 provides access to the analog inputs of the eight ADCs of the TAMC900. As signal conditioning, it provides a differential amplifier with Gain = 1 for each analog input. The figure below shows one analog input path of the TAMC900-A1. -
Page 10: Single Ended Signal Source
4.2 Single Ended Signal Source If a single ended signal source is used, it can be connected to the TAMC900-A1 in the following way: 3.3 Volt ANALOG_IN- LTC6404 LTC2254 ANALOG_IN+ Single Ended TAMC900-A1 Signal Source (TAMC900) Figure 4-2 : Single Ended Signal Source In the above configuration, ANALOG_IN- should not exceed ±1.0 Volt (ADC input voltage range). -
Page 11: Clock
The Clock Inputs are directly routed to the TAMC900. The maximum input voltage of the corresponding Virtex-5 I/Os is 2.5 Volt. The device will be damaged if higher voltage levels are used. TAMC900-A1 User Manual Issue 1.0.2 Page 11 of 17... -
Page 12: Trigger
The Trigger Inputs are directly routed to the TAMC900. The maximum input voltage of the corresponding Virtex-5 I/Os is 2.5 Volt. The device will be damaged if higher voltage levels are used. TAMC900-A1 User Manual Issue 1.0.2 Page 12 of 17... -
Page 13: Pin Assignment
7 Pin Assignment 7.1 Overview Pin 120 Pin 119 SiCA Connector Clock Connector Pin 2e Pin 2 Pin 2a Pin 1 Trigger Connector Pin 1a Analog-In Connector Figure 7-1 : Connector Overview TAMC900-A1 User Manual Issue 1.0.2 Page 13 of 17... -
Page 14: Clock Connector
7.3 Trigger Connector Signal Level Signal Level TRIG_2+ LVDS TRIG_2- LVDS TRIG_1+ LVDS TRIG_1- LVDS TRIG_0+ LVDS TRIG_0- LVDS CASE Front Panel CASE Front panel Table 7-2 : Pin Assignment Trigger Connector TAMC900-A1 User Manual Issue 1.0.2 Page 14 of 17... -
Page 15: Analog-In Connector
The Samtec QTE / QSE Series are used as I/O connection between TAMC900 and the SiCA. The TAMC900 carries a QSE connector, and the mating QTE connector is populated on the SiCA. The stacking height is defined by the QTE connector on the SiCA. TAMC900-A1 User Manual Issue 1.0.2 Page 15 of 17... - Page 16 The Samtec QTE-060-02-L-D-A or compatible is used on the TAMC900-A1. Signal Level Signal Level GP_IO_0 2,5 Volt CMOS SiCA_PWR +6 Volt GP_IO_1 2,5 Volt CMOS SiCA_PWR +6 Volt GP_IO_2 2,5 Volt CMOS SiCA_PWR +6 Volt GP_IO_3 2,5 Volt CMOS SiCA_PWR...
-
Page 17: Table 7-4 : Pin Assignment Sica Connector
GP_IO_12 2,5 Volt CMOS logic Ground GP_IO_13 2,5 Volt CMOS CLKIN_2+ LVDS GP_IO_14 2,5 Volt CMOS CLKIN_2- LVDS GP_IO_15 2,5 Volt CMOS logic Ground Table 7-4 : Pin Assignment SiCA Connector TAMC900-A1 User Manual Issue 1.0.2 Page 17 of 17...