ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
Page 3
PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description 200318 Bracket, Reinforcement S/J 200503 P/S Cover 200520 Screw, #8 x 3/4", Flat Hd, Phillips 200533 Spacer, Mounting 201219 Net Clips 201344 Plastic Knob 201611 Bolt,Hex-Flange, 5/16-18 x 3" 202795 NBA Sticker 203063 Locknut, 3/8-16 Nylon Insert...
Page 4
Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing). Display boards will be mounted as follows: Corner Location 1: Corner Location 2: Corner Location 3:...
Page 5
At corner location 3 slide the pole sleeve (34) inside the mounting stub. At corner location 1, 2 and 4 slide the 3-1/2" diameter end of the display pole (33) inside the mounting stubs. Slide the 3" diameter end of the display pole (24) inside the pole sleeve.
Page 6
Corner Location 1: STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY Display Stand - Top View 3-1/2" Corner “4” Corner “3” 80602 Corner “2” Corner “1” 9H235A 3-1/2" 3-1/2" Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23), extension arm (31) and mounting spacers (4) assemblies to backboard using bolt (7 ) and nut (11) as shown.
Page 7
• Fit rim (25) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). NOTE: Peel protective film from surface of...
Page 8
Corner Location 2: 48” FAN MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View 3-1/2" 3" Corner “4” Corner “3” 80602 Corner “2” Corner “1” 9H235A 3-1/2" 3-1/2" Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23) and extension arm (31) to backboard using bolt (7) and nut (11) as shown.
Page 9
• Fit rim (25) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). NOTE: Tighten nut (17) until flush with end of "T"...
Page 10
Corner Location 3: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View 3-1/2" Corner “4” Corner “3” 80602 Corner “2” Corner “1” 9H235A 3-1/2" 3-1/2" Attach board assembly to pole with carriage bolts (12) and knobs (6) as shown. Install pole cap (21) as shown.
Page 11
Corner Location 4: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View 3-1/2" 3" Corner “4” Corner “3” 80602 61259 Corner “2” Corner “1” 73256 9H235A 3-1/2" 3-1/2" Attach rim (25) to backboard (30) and extension arm (31) with bolts (7), washers (14) and nuts (11).
Page 12
Install net clips. WARNING! USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS ® , OR WHEN ALL SMART CLIPS ® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. P/N 21155402 09/04 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm”...
Page 13
Install net. SIDE VIEW NETCLIP Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP P/N 21155402 09/04...