1. Manuals
  2. Brands
  3. Bose Manuals
  4. Signal Processors
  5. FreeSpace E4 Series II
  6. Owner's manual

Bose FreeSpace E4 Series II Owner's Manual

Business music system
Hide thumbs Also See for FreeSpace E4 Series II:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
FreeSpace
E4 Series II Business Music System
®
OWNER'S GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Bose FreeSpace E4 Series II

Summary of Contents for Bose FreeSpace E4 Series II

  • Page 1: Step 5 - Determine The E4 Requirements . 19 2.3 Auto Volume Layout Examples

    FreeSpace E4 Series II Business Music System ® OWNER’S GUIDE...

  • Page 2: Table Of Contents

    1.0 E4 Introduction ......13 5.0 Using FreeSpace ® Installer™ Software ..34 1.1 The Bose ® FreeSpace ®...

  • Page 3: Freespace

    Contents 8.4 Common problems ..... . 68 8.4.1 Communications port error ... 68 8.4.2 No audio in zone .

  • Page 4: E4 Hardware Description

    3.0 E4 Hardware Description 3.1 Front panel 3.1.1 Controls channels: Green = Normal operation STANDBY – The STANDBY button switches the unit Red = Fault condition between standby and active. The color of the LED above the switch indicates the status: Unlit = No signal Amber = Unit is in standby AUDIO SOURCES –...

  • Page 5: Rear Panel

    CONTROL ® geprüfte LISTED 917D ü V Rheinland FreeSpace E4 Series II Sicherheit AUDIO EQUIPMENT 400 Watt System Electronics This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)This device may not caus e...

  • Page 6: Hardware Installation

    4.0 Hardware Installation 4.1 Introduction 4.3 Placement guidelines • Place the E4 unit where it is protected from heat and allowed This section provides instructions for installing the FreeSpace ® adequate ventilation. E4 system hardware on a tabletop or in a rack. •...

  • Page 7: Rack Mounting The E4 Unit

    4.0 Hardware Installation 4.5 Rack mounting the E4 unit ® Required accessory: FreeSpace E4 System Rack Mount Kit (PC029858) (8) #8-32 x 1/2 in Rack ears Attaching rack ears to the E4 chassis The E4 unit requires three 1.75" (4.4 cm) rack space units with a 16"...

  • Page 8: Installing Accessories

    4.0 Hardware Installation 4.6 Installing accessories 4.6.2 User interfaces Required accessory: FreeSpace E4 System User Interface Kit 4.6.1 Sensing microphones [PC029856 (U.S.), PC029857 (Euro)] or Required accessory: FreeSpace E4 Auto Volume Interface Kit [PC030101 (U.S.), PC030102 (Euro)] or FreeSpace ® E4 System Auto Volume Mic Kit [PC029859 (U.S.), FreeSpace E4 System Page Interface Kit PC029860 (Euro)]...
  • Page 9 4.0 Hardware Installation Keypad schematic: User interface wiring: 1 2 3 4 5 6 7 8 Installer’s Note: Use only standard ethernet (Cat 5) cable to +5VD connect the user interface to the E4 unit. DO NOT use cross- over (XOV) cables. +5VD .33µF +5VD...

  • Page 10: System Wiring

    4.0 Hardware Installation 4.7 System wiring 4.7.3 User interface connections Connect the user interface from each zone to the appropriate Installer’s Note: Disconnect the E4 unit from the AC WALL PLATE CONNECTION jack. (mains) power before making any input/output connections. Installer’s Note: Only use standard ethernet (Cat 5) cable to connect the user interface to the E4 unit.

  • Page 11: Line 1/Line 2 Source Input

    4.0 Hardware Installation 4.7.5 LINE 1/LINE 2 source input 4.7.6 AUX MIC/LINE 3 source input Audio sources can be connected to the LINE 1 and LINE 2 inputs A microphone or an audio source can be connected to the MIC/ using one of the following cable types.

  • Page 12: Page/Mic/Line 4 Source Input

    4.0 Hardware Installation 4.7.7 PAGE/MIC/LINE 4 source input 4.7.8 DIRECT IN/CONTROL source input A microphone or an audio source can be connected to the PAGE/ A microphone or an audio source can be connected to the MIC/LINE 4 input using one of the following cable types. DIRECT IN input using one of the following cable types.

  • Page 13: Amplifier Outputs

    4.0 Hardware Installation 4.7.9 Amplifier ZONE OUT outputs 4.7.10 Output voltage setting (70/100V) Speaker systems in up to four zones can be connected to the Check the OUTPUT VOLTAGE switch setting and change if ZONE OUT amplifier outputs. needed. OUTPUT Installer’s Note: Please notice the polarity markings on VOLTAGE the ZONE OUT 1-4 connectors.

  • Page 14: Zone 4 Line Out Output

    Bose ® amplifier installed for a large zone. The 12V for 220-240VAC. control output is used to connect to Bose amplifier sequence inputs. Fuse box configuration The fuse box is configured at the factory according to the specifi-...

  • Page 15: Using Freespace Installer™ Software

    How you can obtain warranty service: Remedies: 1. You can ship the system to either a Bose Service Agency or to Bose directly with a proof of purchase from an authorized dealer. The provisions of this limited warranty are in lieu of any other Please: warranties or conditions, except those provided by law.
  • Page 16 ©2004 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA 279145 AM Rev.00 CCM-000922...

Table of Contents