Auto Correction Of Hand Home Positions; Adjusting Home Positions Manually; Button Operation Tone - Casio 5114 Operation Manual

Swapping the Home City and World Time City
You can use the procedure below to swap your Home City with your World Time City.
This function comes in handy for those who often travel between two different time zones.
The following example shows what happens when the Home City and World Time City are swapped while
the Home City originally is TOKYO (TYO) and the World Time City is NEW YORK (NYC).
Before swapping
(Standard time)
After swapping
(Daylight saving time)
To swap your Home City and World Time City
1. In the World Time Mode, use A to select the city code you want to make your World Time City.
Keep pressing A until the second hand is pointing to the city code you want.
•
• In this example, you would move the second hand to NEW YORK (NYC) in order to select New York as
the World Time City.
2. Hold down C until each of the following steps occurs.
) appears on the digital display. ➝ Hold (
• Hold (
• This will cause the World Time City (NEW YORK/NYC in this example) you selected in step 1 of this
procedure your new Home City, and your previously selected Home City (TOKYO/TYO in this
example) will become your new World Time City. The digital display and hands will indicate the
current time in your new World Time City (TOKYO/TYO in this example).
Note
• If your current World Time City supports time calibration signal reception, making it your Home City
enables calibration signal reception for that city.

Auto Correction of Hand Home Positions

Strong magnetism or impact can cause the hands of the watch to be off, even if the watch is able to
perform the signal receive operation. This watch performs an auto correction procedure to ensure that the
hands are always in the correct positions.
• Auto correction is performed only while the watch is in the Timekeeping Mode. Auto correction is not
performed if the watch is in the Timekeeping Mode while a Countdown Timer Mode operation is in
progress.
• Each hour, the watch performs automatic correction of the hand positions from –55 minutes to +5
minutes.
• You also can trigger auto correction of hand home positions manually, if you want. See "To trigger auto
correction of hand home positions" for more information.
• Auto correction of hand home positions can take up to three and a half minutes to complete.
• If hand positions are off by one hour or more, correct them using the procedure under "To trigger auto
correction of hand home positions" or "Adjusting Home Positions Manually".
To trigger auto correction of hand home positions
• Perform the following procedure when the time setting is off.
1. Use D to enter the Hand Home Position Adjustment Mode.
• The digital display will show the current Timekeeping Mode time. You
can check the hand positions by comparing the digital time with
the time indicated by the analog hands.
2. Hold down A for about three seconds until each of the following steps
occurs.
Hold HS appears on the digital display. ➝ H-S fl ashes.
•
• This starts auto hand home position adjustment.
• To cancel an ongoing auto hand home position operation part way
through, press A .

Adjusting Home Positions Manually

Strong magnetism or impact can cause the hands of the watch to be off, even if the watch is able to
perform the signal receive operation. When this happens, you can manually adjust the hand home
positions to ensure correct timekeeping.
• Hand home position adjustment is not necessary as long as the hands are indicating time correctly.
To adjust home positions manually
1. Enter the Hand Home Position Adjustment Mode.
• The digital display will show HS, followed by the current Timekeeping
Mode time. You can use the digital display to check if the hand
positions are correct and to confi rm whether the analog time
indication matches the digital time.
2. Hold down E until each of the following steps occurs.
Hold SET appears on the digital display. ➝ SEC 00 fl ashes.
•
• The second hand should move to 12 o'clock at this time. If it doesn't,
use A (+) to move the second hand so it aligns with 12 o'clock.
3. After the second hand is aligned correctly, press D.
• The hour and minute hands should move to 12 o'clock. If they don't,
use A (+) and C (–) to move them so they align with 12 o'clock.
Pressing D here returns to the second hand home position
•
adjustment in step 2.
4. After adjusting the hour hand and minute hand home positions, press E.
• After adjusting the home positions of the hands, leave the watch in a location where time calibration
signal reception is good and perform manual receive. Next, check to make sure that the hands are
indicating the time correctly. See "To perform manual receive" for more information.
Illumination
The face of the watch is illuminated for easy reading in the dark.
The watch's auto light switch turns on illumination automatically when
you angle the watch towards your face.
• The auto light switch must be turned on for it to operate.
To turn on illumination manually
Press L in any mode to turn on illumination.
• You can use the procedure below to select either one second or three
seconds as the illumination duration. When you press L, illumination
will remain on for about one second or three seconds, depending on
the current illumination duration setting.
• The above operation turns on illumination regardless of the current
auto light switch setting.
• Illumination cannot be used during time calibration signal reception, in
a sensor mode, while a compass operation is in progress, or while
hand home position adjustment is being performed.
Operation Guide 5114
Home City World Time City
Tokyo New York
10:08 p.m. 9:08 a.m.
(Daylight saving time)
New York Tokyo
9:08 a.m. 10:08 p.m.
(Standard time)
) disappears.
To change the illumination duration
1. In the Timekeeping Mode, hold down E until each of the following
steps occurs.
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
2. Use D to cycle through the settings on the digital display until the
current illumination duration (LT1 or LT3) is shown.
• See step 3 under "To change the current time and date settings
manually" for information about how to scroll through setting
screens.
3. Press A to toggle the illumination duration between three seconds (LT3 displayed) and one second
(LT1 displayed).
4. After all the settings are the way you want, press E to exit the setting screen.
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on,
whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and
then tilting it towards you more than 40 degrees causes
illumination to turn on.
Warning!
• Always make sure you are in a safe place whenever you are reading the display of the watch
using the auto light switch. Be especially careful when running or engaged in any other activity
that can result in accident or injury. Also take care that sudden illumination by the auto light
switch does not startle or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned off before riding
on a bicycle or operating a motorcycle or any other motor vehicle. Sudden, unintended operation
of the auto light switch can create a distraction, which can result in a traffi c accident and serious
personal injury.
Note
• This watch features a "Full Auto LED Light", so the auto light switch operates only when available light
is below a certain level. Illumination does not turn on under bright light.
• The auto light switch is always disabled, regardless of its on/off setting, when any one of the following
conditions exists.
While an alarm is sounding
During sensor measurement
While a bearing sensor calibration operation is being performed in the Compass Mode
While a receive operation is in progress in the Receive Mode
While a hand home position adjustment operation is in progress
To turn the auto light switch on and off
1. In the Timekeeping Mode, hold down E until each of the following
steps occurs.
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
2. Use D to cycle through the settings on the digital display until the
current auto light switch setting (AT OFF or AT On) is fl ashing on the
digital display.
• See step 3 under "To change the current time and date settings
manually" for information about how to scroll through setting
screens.
3. Press A to toggle the auto light switch setting between on (On) or off (OFF).
4. After the setting is the way you want, press E to exit the setting screen.
Illumination Precautions
• Frequent use of illumination can run down the battery, which will require exposing the watch to light for
charging.
The following guidelines give an idea of the charging time required to recover from a single illumination
operation.
Approximately fi ve minutes exposure to bright sunlight coming in through a window
Approximately 50 minutes exposure to indoor fl uorescent lighting
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of your arm can
cause frequent activation of the auto light switch and illumination. To avoid running down the battery,
turn off the auto light switch whenever engaging in activities that might cause frequent illumination.
• Note that wearing the watch under your sleeve while the auto light switch is turned on can cause
frequent illumination and can run down the battery.
• Illumination may not turn on if the face of the watch is more than 15 degrees above
or below parallel. Make sure that the back of your hand is parallel to the ground.
• Illumination turns off after the preset illumination duration, even if you keep the
watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the
starting position (parallel with the ground) and then tilt it back towards your face
again. If this does not work, drop your arm all the way down so it hangs at your
side, and then bring it back up again.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.

Button Operation Tone

The button operation tone sounds any time you press one of the watch's buttons. You can turn the button
operation tone on or off as desired.
• Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and Countdown Timer
Mode alarm all operate normally.
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down E until each of the following
steps occurs.
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
2. Use D to cycle through settings on the digital display until the current
button operation tone (MUTE or BEEP ) is displayed.
• See step 3 under "To change the current time and date settings
manually" for information about how to scroll through setting
screens.
3. Press A to toggle the button operation tone between on (BEEP ) or
off (MUTE).
4. After the setting is the way you want, press E to exit the setting
screen.
More than More than
40° 40°
Wear the watch on the Wear the watch on the
outside of your wrist outside of your wrist
9