Auto Mode - Dometic Silhouette S1521 Installation And Operating Instructions Manual

WAY display panel.
2 -
UP INSTRUCTIONS
START
A. A 12 volt DC supply must be available for the
electronic control to function.
B. Press the main power ON/OFF button (1) to the
DOWN position.
C. Press the TEMPERATURE SELECTOR BUTTON (3)
P-WAY Model or (4) 3-WAY Model until the lamp at
the desired setting is illuminated.
2-WAY MODEL

AUTO MODE

1. Move the AUTO/GAS mode selector button (2) to
the DOWN position. (If 120 volts AC is available, the
AC mode indicator lamp (B) will illuminate indicat-
ing AC operation. If 120 volts AC is not available, the
GAS mode indicator lamp (C) will illuminate and the
control system will automatic switch to GAS opera-
tion.
2. If the CHECK indicator lamp (E) illuminates and the
GAS mode indicator lamp (C) is off, the controls
have failed to ignite the burner in the GAS mode.
GAS operation may be reset by pressing the main
button
power ON/OFF
tion. (see step 2 under GAS MODE)
3. Press the TEMPERATURE SELECTOR button (3)
until the lamp at the desired position is illuminated.
GAS MODE
1. Move the AUTO/GAS mode selector button (2) to
the UP position_ The GAS mode indicator lamp (C)
will illuminate. After 45 seconds the burner should
be ignited and operating normally.
2. On the initial refrigerator start-up, it may take longer
than 45 seconds to allow air to be purged from the
gas line. If the gas does not ignite within 45 seconds
the CHECK indicator lamp (E) will illuminate and the
GAS mode indicator lamp (C) will go off. To reset
when the CHECK indicator lamp (E) is illuminated,
press the main power ON/OFF button (1) to the OFF
and then ON position.
NOTE: Do not continue to reset GAS operation if the
CHECK indicator lamp continues to be illuminated after
several tries.
3. Press the TEMPERATURE SELECTOR button (3)
until the lamp at the desired position is illuminated.
TO SHUT OFF THE REFRIGERATOR
The refrigerator may be shut off while in any mode of
operation by pressing the main power ON/OFF button
to the UP (OFF) position. This shuts off all DC power to
the refrigerator.
10
(1) to the OFF than ON posi-
3 - WAY display panel.
3-WAY MODEL
AUTO MODE
1. Press the DC mode selector button (2) to the UP
(OFF) position.
2.
Move the AUTO/GAS mode selector button (3) to
the DOWN position. (If 120 volts AC is available, the
AC mode indicator lamp (B) will illuminate indicat-
ing AC operation. If 120 volts AC is not available, the
GAS mode indicator lamp (C) will illuminate and the
control system will automatic switch to GAS opera-
tion.
If the CHECK indicator lamp (E) illuminates and the
3.
GAS mode indicator lamp (C) is off, the controls
have failed to ignite the burner in the GAS mode.
GAS operation may be reset by pressing the main
power ON/OFF button (1) to the OFF than ON posi-
tion. (see step 2 under GAS MODE)
4. Press the TEMPERATURE SELECTOR button (4)
until the lamp at the desired position is illuminated.
GAS MODE
1. Press the DC mode button (2) to the UP (OFF) posi-
tion.
2. Move the AUTO/GAS mode selector button (3) to
the UP position. The GAS mode indicator lamp (C)
will iliimunate. After 45 seconds the burner should
be ignited and operating normally.
On the initial refrigerator start-up, it may take longer
3.
than 45 seconds to allow air to be purged from the
gas line. If the gas does not ignite within 45 seconds
the CHECK indicator lamp (E) will illuminate and the
GAS mode indicator lamp (C) will go off. To reset
when the CHECK indicator lamp (E) is illuminated,
press the main power ON/OFF button (1) to the OFF
and then ON position.
NOTE: Do not continue to reset GAS operation if the
CHECK indicator lamp continues to be illuminated after
several tries.
4. Press the TEMPERATURE SELECTOR button (4)
until the lamp at the desired position is illuminated.
DC MODE
1.
Press the DC mode indicator button (2) to the down
position.
2. Press the TEMPERATURE SELECTOR button (4)
until the lamp at the desired position is illuminated.