PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
TABLE OF CONTENTS 1. INTRODUCTION............................4 1.1 C ..............................4 HECKLIST 1.2 A 1000B 1000B -LX/SX S ..........4 BOUT THE MART EDIA ONVERTER 1.3 F ..............................4 EATURES 1.4 S ............................5 PECIFICATION 1.5 P ........................... 6 RODUCT UTLOOK 2.
Smart Media converter can be use us a standalone unit when it power on by it’s DC adapter. Or use as a slide-in module to the PLANET new 19-inch Web Smart 16-Slots Media converter chassis (MC-1600MR/MC-1600MR48), with this Web Smart Media converter chassis, the GST-70x able to manage and status monitor through the local RS-232 console and remote web interface.
1.5 Product Outlook Right View: there is one RJ-45 twisted-Pair jack (Auto-MDI/MDI-X), one fiber-optic connector (vary by model) and six LED indicators. Left View: there is one DC jack for DC 5V power adapter. LED Indicators Color Status Indication PWR(Power) Green Lights On Power on –...
Turn on the power of the device/station, the TX Link /Act and LX/SX Link/Act LEDs should light when all cables are attached. 1000Base-T Cat. 5/5e TP Cable Network GST-70X PLANET 1000Base-SX/LX Fiber Network Gigabit Ethernet Converter 1000Base-T to1000Base-SX Notice: 1. RJ-45/STP, UTP Cat 5/5E, straight/crossover cable is accepted.
2.2 Slide Media Converter module into MC-1600MR/R48 Chassis installation Step 1- Unscrew and pull out the GST-70x Media Converter board. Step 2- Remove a blank faceplate from an empty expansion slot on the front of the chassis. The GST-70x Media Con- verter board can be installed in any expansion slot.
Standalone and centralize management Media Converter installation Afford the current network grows and expanding, the PLANET GST-70x provide advanced Media conversion technology to fill this kind of demand. The GST-70x provide the diverse fiber connect type options to meet different network application, it is very flexible for GST-70x work as a standalone devices or install into the central Web Smart Media converter chassis for centralize management.
3. MANAGE THE MEDIA CONVERTER This product provides two different managed methods – configure through its DIP Switch or install into the central Web Smart Media converter chassis for centralize management. This section describes how to managed the GST-70x through its DIP Switch and Web Smart Media converter chassis. Before use the GST-70x smart function, please read this chapter carefully.
3.2 Managed Media Converter module through MC-1600MR/R48 Chassis The Web Smart Media Coverter Chassis that can control GST-70x through the management system, GST-70x can be controlled through Web Browser and terminal emulation program. The Web Smart Media Converter Chassis will display out the status of GST-70x, also the Web Smart Media Coverter Chassis can control the function through the management system.
4. LINK PASS THROUGH FUNCTION The LFP function includes the Link Fault Pass Through function (LLCF/LLR) and the DIP Switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net. The DIP Switch provides disable or enable the LFP function.
4.2 Link Loss Return (LLR) The fiber ports of GST-70X have been designed with an LLR function for troubleshooting a remote connection. LLR works in conjunction with LLCF. When LLR is enabled*, the port’s transmitter shuts down when its receiver fails to detect a valid receive link. LLR should only be enabled on one end of the link and is typically enabled on either the unmanaged or remote device.
5. TROUBLESHOOTING This chapter contains information to help you solve issues. If the GST-70x is not functioning properly, make sure the GST-70x was set up according to instructions in this manual. The Power LED is not lit Solution: Check the power cable connection between power adapter and GST-70X. Why I connect GST-70x to device with 1000Base-LX/SX interface and the 1000Base-LX/SX fiber con- nection fail? Solution:...
APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI-X BI_DA+ BI_DB+ BI_DA- BI_DB- BI_DB+ BI_DA+ BI_DC+ BI_DD+ BI_DC- BI_DD- BI_DB- BI_DA- BI_DD+ BI_DC+ BI_DD- BI_DC- A.2 RJ-45 cable pin assignment The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the...
5000* Notice: 1: Consult your local dealer for more about PLANET single mode fiber connectivity. 2. The Single-mode port (1000Base-LX port) of GST-702S, GST-705A, GST-706A15/B15 and GST-706A60/B60 is complied with LX 5 kilometers and provides additional margin allowing for a 10/15/60 kilometers Gigabit Ethernet link on single mode fiber.