ABLE ONTENTS Introduction Safety Information/Useful Tips ....................3 Before Calling Service ........................ 4 Basic Installation/Functions Hooking Up Your TV (Basic Connection)................5 Use/Care of Remote Control ....................5 Back Connectors ......................... 6 Remote Controls ......................... 7 TV Installation Activating TV Setup Menu ......................8 TV Setup Main Menu ........................
AFETY NFORMATION AND SEFUL AFETY NFORMATION • Disconnect mains plug when : – the red light below the TV screen is flashing continuously. – a bright white line is displayed across the screen. – cleaning the TV screen. Never use abrasive cleaning agents. Use a slightly damp chamois leather or soft cloth.
EFORE ALLING ERVICE Below is a list of frequently occurred symptoms. Before you call for service, make these simple checks. Some of these symptoms can easily be rectified if you know what to do. Symptom What you should do Colour patch •...
TV (B OOKING UP YOUR ASIC ONNECTION NTENNA ONNECTION • Connect the aerial plug to the antenna socket ¬ on the backcover. AINS ONNECTION • For correct mains voltage, refer to type sticker at the rear of the TV set. •...
ONNECTORS ARNING ISK OF ELECTRIC SHOCK DO NOT REMOVE THIS COVER (RJ12) O NOT CONNECT TELEPHONE CABLE TO MART CONNECTOR Smart Card slot Note: Monitor Component Video Input 1. Do not connect Video In and S-Video Ext Spk Video In concurrently.
EMOTE ONTROLS Three types of remote controls could be used for setup purpose: POWER RECALL TEXT SMART SLEEP GUEST SETUP GUIDE RESET A/CH Ñ - CLOCK A / V RC2886 RC2887 RC2573GR (RC19335018/01) (RC19335025/01) (optional) For the purpose of explanation, RC2886/RC2887 is used. Remote control RC2573GR is optional and can be purchased separately.
TV S CTIVATING ETUP RC2886/RC2887 ITH REMOTE CONTROL (only when SECURITY in the TV SETUP menu is set to LOW). To activate TV Setup menu. Select a channel number. Key in 3 1 9 7 5 3. Press H . The above sequence should be done within 20 seconds and TV SETUP menu will appear.
TV S ETUP Below shows the structure of the menu items TV SETUP LANGUAGE ENGLISH É NO. OF CHANNELS É INSTALLATION É CLOCK SETUP BRIGHTNESS |||||| ||||||| COLOUR ||||||| ||||||| CONTRAST ||||||||| |||| SHARPNESS ||||||||||| (only for NTSC signal) TINT ||||||||| |||| (only for 29HT model)
TV S ETUP MENUS ANGUAGE When you first enter the TV SETUP menu, LANGUAGE is highlighted. You may select other languages available with the ˝ ) or ) key. ˙ OF CHANNELS Show the number of channels under each category type. Enter the TV SETUP menu and highlight NO.OF CHANNELS.
TV I NSTALLATION NPUT This menu item selects the input source to be assigned per channel. The selectable sources are FRONT END, AV1, AV2, AV3, CVI, AV2YC or AV3YC (dependent on model). To select press the ) or ) key. ˝...
(only for models with Teletext feature) ELETEXT ANGUAGE This option allows toggling between different Teletext languages. W for Western English or A for Arabic. The default selection is W. For models without Teletext feature, selection of W or A has no effect. IDEO LANK To blank out picture of the channel, select YES.
Page 13
TV S ’ ETUP MENUS RIGHTNESS OLOUR ONTRAST HARPNESS Enter the TV SETUP menu and highlight accordingly. Preset the TV by adjusting the brightness, colour, contrast, sharpness or tint (applicable for NTSC signal only) of the picture. All these 5 items are also accessible to users via the key for personal settings.
Page 14
I/II (only for Stereo models) UDIO This menu item is to enable the switching from Stereo or Nicam Stereo to Mono, or to choose between Dual I or Dual II in case of bilingual transmission. When the sound mode is switched to Mono, the indication is displayed in red.
Page 15
OWER Select STANDARD, STANDBY, FORCED or ON mode. The different modes are as explained below: STANDARD: TV will be automatically switched to the last status (STANBY or ON) whenever the mains power is turned ON or resumed after a power interruption. STANDBY: TV will be automatically switched to STANBY(even if the last status was ON) whenever the mains power is turned ON or resumed after a power interruption.
Page 16
(for SmartConnect/SmartCard-R/Y models only) NTERFACE Enables the communication of the TV with the DCM when YES is selected. This is specifically applicable to the Interactive System TV, providing the interactivity feature between a DCM card of the Service Provider and the dedicated System TV. UDIO IDEO To blank the screen when no signal is received.
Page 17
LINE 2: O CREATE MESSAGE WITH Highlight LINE 2 with the ) key. Press the ) key to begin. The cursor ˙ ¸ will appear in the first character position. To input characters, press the ) or ˚ ) key to select from the list:- A to Z, 0 to 9, , –, •,/, :, =, ?, ;, <, >, @ or space.
ELETEXT CCESS (for models with Teletext feature only) Select YES to enable the Teletext feature or NO to disable the Teletext feature. For models without Teletext feature, selection of YES or NO has no effect. ECURITY Select HIGH and only remote control RC2573GR can be used to enter TV Setup menu. THER FEATURES LARM The Alarm feature will require the time to be set correctly according to the CLOCK SETUP...
Page 19
This page is intentionally left blank p13-20_081205 12/8/05, 5:24 PM...