Advertisement
Available languages
Available languages
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
1.
Make certain the power source conforms to the electrical requirements of the Fan.
2.
Make certain that the room is equipped with a working smoke detector.
3.
Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,
or injury to persons.
4.
To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.
5.
Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING
OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE
LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6.
This Fan must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres
where gasoline, paint or flammable liquids are used or stored.
7.
DO NOT use Fan in or near a window. Rain may create an electrical hazard.
The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no circumstances
must the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be replaced with a properly
grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and all applicable local codes and
ordinances. This work must be done only by a qualified electrician, using copper wire only.
USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC-
TION MAY CREATE THE RISK OF ELECTRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED
IN CANADA.
8.
Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an exten-
sion cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed. NEVER use a single
extension cord to operate more than one Fan. Do not plug Fan into any other cord connected device, such as a power strip, cord
reel, surge protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.
9.
NEVER operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner.
There are no user serviceable parts.
10. NEVER insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire,
or damage the Fan. To reduce the risk of fire, DO NOT block or tamper with the Fan in any manner while it is in operation.
11. Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power
Cord so the Fan or other objects are not resting on it. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be
tripped over.
12. This Fan is not intended for use in wet or damp locations. Never locate a Fan where it may fall into a bathtub or other water container.
NEVER use Fan where flammable liquids are used or stored.
13. NEVER use Fan outdoors.
14. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please
refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical require-
ments for Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
15. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET THE REQUIRE-
MENTS OF NEC ARTICLE 500 (2008).
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS
FAN WITH ANY SOLID STATE SPEED CONTROL DEVICES.
SAVE THESE INSTRUCTIONS
Rev. C 8/10
2
FUNCIONAMIENTO
1. Cuidadosamente retire el Ventilador de la bolsa plástica y la
caja. Arme la unidad siguiendo estas instrucciones.
2. Coloque el ventilador sobre una superficie firme y nivelada.
ADVERTENCIA:
Los tacos de plástico o hule, tales como
las patas de esta unidad, pueden pegarse a la superficie de los
muebles. La unidad podría dejar un residuo capaz de oscurecer,
manchar o dejar marcas permanentes en el acabado de ciertas
superficies de muebles, incluyendo superficies y pisos de
madera.
3. Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos en los
tomacorrientes, pueden deslizarse parcial o
completamente fuera del tomacorriente con un leve
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un grave peligro de incendio; si está cubierto por una
cortina o tela, el riesgo de incendio es aún mayor.
4. Encienda el Ventilador seleccionando la velocidad deseada
con la situada al costado del Ventilador.
0 – Apagado
3 – Alta
2 – Media
1 – Baja
5. Para ajustar el ángulo vertical, presione el panel del Ventilador
hacia delante o hacia atrás hasta la posición deseada. Es normal
escuchar un sonido de clic mientras realiza esta función.
Reinicio del Interruptor:
Se proporciona un interruptor de 10 amp como una opción de
seguridad para su Ventilador. Cuando utilice una herramienta
que tenga más amperaje del permitido, el interruptor saltará.
Para reiniciarlo, desconecte la herramienta que esté
provocando que el interruptor salte y oprima el Botón De
Reinicio adyacente a los tomacorrientes del Ventilador.
6. Para APAGAR el ventilador, gire la Perilla de Encendido
a la posición APAGADO (0) y desconecte la unidad del
tomacorrientes eléctrico.
4914ES
Rev. C 8/10
MODELO 4914
10 AMP MAX
Botón De
Reinicio
0
3
2
1
AMP MAX
Figura 1A
7
0
3
2
1
Figura 1
4914ES
Advertisement
