56" Wiring Diagram - Back - Zenith R50V26 Service Manual

to Speaker(PR)
LX-ZCAT3035-1330
E007
PFT
PV154 - 923-03506

56" Wiring Diagram - Back

PR make LEAD CLAMPER
double loop
N008
PDC1 make a loop
PAQ1,PL
PR
PQS1
PQS2
PAQ1,PL
PR
PQD1
PQS1
PQS2
PCB,MB PCR,MR
ANODE(B)
to CONTROL
P.W.B.
PFT PFS, PFT
MB
MB MG
PCB
WIRE
CLAMP VO
N003
PFS
ANODE(B)
FOCUS
SCREEN
FOCUS (G)
PFS
SCREEN (G)
FOCUS (B)
PVMS
SCREEN(B)
SCREEN(B) SCREEN(G)
VM P.W.B.
FOCUS
PVC2 PZC
FOCUS (B)
to
PCV
VM
PZV CPT P.W.B.(B)
CPT P.W.B.(G)
P.W.B.
PZC PZC
E003 PZV PZV
MGZ-E1630MRF-CLAMP MGZ-E1630MRF-CLAMP
PVS1
MGZ-E1630MRF-CLAMP
E004
PFS
PZV
PZV PZC
PZC
PL
PR
PAQ1
PQS2
PQS1
SIGNAL P.W.B.
SRS P.W.B.
TUNER 1
TUNER 2
PFT
TERMINAL P.W.B.
ANTENNA TERMINAL BOARD.
BACK SIDE
LEAD CLAMPER
MAG-FERRITE CORE 133
N008
E001
PAQ1,PL,PQD2
PQS1,PDC1
PQS2,PQD1
PCB,PCG
PL
make a loop
PDC1
PCR PCB PCG
MR MB MG
ANODE(G) PDF2
ANODE(R)
PCG
PCR,MR
make a loop
MG
FOCUS PACK
MR
MR
MR
FOCUS(R)
MG
SCREEN(R)
to
N007
VM PCR
PCG
PURSE LOCK
P.W.B.
016
(G) (B)
(G) (B)
SCREEN(R)
PDC1
FOCUS
(G)
PCV
PCB,MB
(R)
PCG,MG
PCR,MR
PDF2
N003
Hold Anode(B)
make double
loops
MB
PSD1
PDS1
PDK1
MR
PSD2
MG
PQD2
PSD3
PDF1
PDK3
PDC1 PCR
DEFLECTION
P.W.B.
B
PDK4
FOCUS PCG
ANODE(R)
PSF
R G
ANODE(G)
ANODE(B)
LX-ZCAT2032-0930
E002
FBT
PCB
PDF1
PDKP
PQD1 PDF2
CONVERGENCE
PS
P.W.B.
NOTE: Refer to the figure (04/page) when the HV
connector (anode lead) is removed or inserted.
NOTE: Anode lead should be separated from others
wires. (min. 10mm)
Anode lead must not be twisted during the
operation of wiring dress.
5-6
Refer to the figure below
about the assembly if
FOCUS PACK leads.
SCREEN
(G)
(B)
PDF2
(B)
(G)
FOCUS
PSF
from SENSOR P.W.B.
FOCUS PACK
PDF2,PSF
FOCUS(R,G,B)
PDS1
SCREEN(R,G,B)
MAG-FERRITE CORE 133
N001
E001
SK
BINDER
PQD1,PQS2 PQS1 make a loop
PQD2 make double loop
N001
SK BINDER
to Speaker(PL) P#:3763752
make a loop
PL
CATCH HOLDER
(BACK VIEW)
PAQ1
PQD2
PQS1
MGZ-E1630MRF
E005
PQD1
make a loop
PQS2
MARK SHOULD BE APPLY A LEAD CLAMP(N008)
(LEAD CLAMP PARTS No. IS 3813121.)
POWER SUPPLY
P.W.B.
MARK SHOULD BE APPLY A LEAD CLAMP(N011)
DIGITAL
CONVERGENCE (LEAD CLAMP PARTS No. IS 3875441.)
UNIT
PA
POWER CORD
THIS DRAWING APPLIES
TO R56W28
(ZP14C CHASS.).
ZP26/28 - EXPLODED VIEWS
(R)
(R)
UFPK