Page 1
Manual de Operario Esta máquina puede utilizar gasolina con un con- tenido de hasta el 10% de etanol (E10). HU725BBC / 961430094 El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto. Please read the operator's manual carefully and make sure you understand the instructions before using the machine.
SAFETY RULES Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • See manufacturer’s instructions for proper operation Look for this symbol to point out im- and installation of accessories.
1.6 Quarts Should you experience any problem you cannot easily and Type: (Unleaded Regular Only) remedy, please contact your nearest Husqvarna or other Oil Type (API SG–SL): SAE 30 (above 0°C/32°F); authorized service center/department. We have competent, SAE 5W-30 (below 0°C/32°F) well-trained tech ni cians and the proper tools to service or repair this lawn mower.
ASSEMBLY Read these instructions and this man u al in its entirety before you attempt to assemble or operate your new lawn mow er. OPERATOR MOWING PRESENCE PO SI TION IMPORTANT: THIS LAWN MOWER IS SHIPPED WITH- CONTROL OUT OIL OR GASOLINE IN THE ENGINE. Your new lawn mower has been as sem bled at the factory LIFT with the ex cep tion of those parts left unassembled for ship-...
ASSEMBLY TO ASSEMBLE GRASS CATCHER INSTALL STARTER ROPE (See Fig. 4) (See Fig. 3) 1. Loosen T-knob. 1. Put grass catcher frame into grass bag with rigid part 2. Place throttle control in STOP position. of bag on the bottom. Make sure the frame handle is 3.
(E10) will void the product warranty. MEETS CPSC SAFETY REQUIREMENTS Husqvarna rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U.S. Consumer Product Safety Commission. OPERATOR PRESENCE CONTROL BAR – must be THROTTLE / ENGINE CONTROL –...
OPERATION The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or per- forming any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask over spectacles.
Page 8
OPERATION DRIVE CONTROL (See Fig. 7) DRIVE CONTROL ADJUSTMENT (See Fig. 8) • Self-propelling is controlled by pulling either drive control Over time, the drive control system may become “loose”, lever rearward to the handle. The further toward the resulting in decreased speed. There is a turnbuckle on handle a lever is pulled, the faster the unit will travel.
OPERATION TO CONVERT MOWER SIDE DIS CHARG ING (See Fig. 11) Your lawn mower was shipped ready to be used as a • Rear door must be closed. mulcher. To convert to bagging or discharging: • Open mulcher door and install dis charge defl ector under door as shown.
OPERATION TO EMPTY GRASS CATCHER (See Fig. 12) GASOLINE 1. Lift up on grass catcher using the frame han dle. OIL FILL CAP/ FILLER CAP DIPSTICK 2. Remove grass catcher with clippings from under lawn mower han dle. 3. Empty clippings from bag using both frame handle and bag handle.
Page 11
OPERATION • For extremely heavy cutting, reduce the width of cut TO STOP ENGINE (See Fig. 14) by overlapping previously cut path and mow slowly. • To stop engine, place throttle/engine control in STOP • For better grass bagging and most cutting conditions, position.
MAINTENANCE BEFORE AFTER EVERY EVERY EVERY BEFORE EACH EACH 25 HOURS STORAGE HOURS OR SEASON HOURS Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication...
MAINTENANCE LAWN MOWER TO REPLACE BLADE 1. Position the blade on the Blade Brake/Clutch. Always observe safety rules when performing any main- te nance. 2. Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine. TIRES 3.
MAINTENANCE Change the oil after every 25 hours of operation or at least CAUTION: Pe tro leum solvents, such as once a year if the lawn mower is not used for 25 hours in ker o sene, are not to be used to clean one year.
DRIVE BELT If your mower does not operate properly due to suspected drive belt problems, take your mower to a Husqvarna or other qualifi ed service center for repair and/or ad just ment. FIG. 20...
IMPORTANT: NEVER TAMPER WITH THE ENGINE take your lawn mower to a Husqvarna or other qualifi ed GOVERNOR, WHICH IS FACTORY SET FOR PROPER service center for repair and ad just ment.
Drain oil (with engine warm) and replace with clean engine before storing in any enclosure. oil. (See “ENGINE” in the Maintenance section of this manual). TROUBLESHOOTING POINTS See appropriate section in manual unless directed to a Husqvarna or other authorized repair center. PROBLEM CAUSE CORRECTION Does not start 1.
TROUBLESHOOTING POINTS See appropriate section in manual unless directed to a Husqvarna or other authorized repair center. PROBLEM CAUSE CORRECTION Loss of power 1. Rear of lawn mower housing or cutting 1. Raise cutting height. blade dragging in heavy grass.
Page 19
(a) Engines and Attachments.Except where otherwise indicated on Exhibit A, all Engines and Attachments are not covered by this Limited Warranty. In most cases, these items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and included with the product at the time of purchase.
Page 20
10. Authorized Husqvarna Servicing Dealer/Center. In order to obtain warranty coverage it is your responsibility (at your expense) to deliver or ship your Husqvarna unit to an authorized Husqvarna Servicing Dealer/Center and arrange for pick-up or return of your unit after the repairs have been made.
Riding Lawn Tractors: Frame, Chassis, Front Axle 5 Years No Warranty No Warranty Engine* Transmission (if made by Husqvarna/Peerless) 3 Years No Warranty No Warranty Transmission (if third party)** XLS Models only - stamped deck shell. Armor Protected Limited Warranty...
Page 22
** See reference 1 (b) of the warranty statement. RZ - Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network. EZ - One (1) Year Commercial warranty, parts & labor, with Husqvarna. Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
REGLAS DE SEGURIDAD IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. • Detenga la cuchilla o las cuchillas cuando cruce por calzadas, Busque este símbolo que señala las precau- calles o caminos de grava.
Ponga en conocimiento de los demás que está cortando el césped. V. SERVICIO • Nunca haga funcionar una máquina dentro de un área cer- IV. MANEJO SEGURO DE GASOLINA rada. Usar mucha atención cuando se maneja gasolina. La gasolina es •...
MONTAJE / PRE-OPERACIÓN Lea estas instrucciones y el manual completamente antes de BARRA DE POSICIÓN tratar de montar u operar su segadora nueva. IMPORTANTE: CONTROL PARA Este cortacesped viene SIN ACEITE O GASOLINA en el mo- QUE EXIGE LA SEGAR tor.
Page 26
MONTAJE / PRE-OPERACIÓN PARA MONTAR EL RECOGEDOR DE CÉSPED INSTALACIÓN DEL CORDÓN ARRANCADOR (Vea Fig. 3) (Vea Fig. 4) Ponga el bastidor del recogedor de césped en la bolsa del Afl oje una manilla-T. césped con la parte rígida de la bolsa en la parte inferior. Mueva la palanca de control de aceleración del motor a la Asegúrese que el mango del bastidor esté...
OPERACIÓN FAMILIARÍCESE CON SU SEGADORA LEA ESTE MANUAL DEL DUEÑO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU SEGADORA. Compare las ilustraciones con su segadora para familiarizarse con la ubicación de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. Estos símbolos pueden apareser sobre su segadora o en la literatura proporcionada con el producto.
Page 28
OPERACIÓN La operación de cualquier segadora puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protección para los ojos mientras opere su segadora o cuando haga ajustes o reparaciones. Recomendamos gafas o una mascara de seguridad de visión amplia de seguridad usada sobre las gafas.
Page 29
OPERACIÓN CONTROL DE LA IMPULSIÓN (Vea Fig. 7) AJUSTE DEL MANDO (Vea Fig. 8) • La autopropulsión se controla manteniendo tirando cualquiera Ocasionalmente, el sistema de mando puede “afl ojarse”, provo- palanca de accionamiento atrás hacia el mango. Cuanto más cando una disminución de la velocidad.
Page 30
OPERACIÓN PARA CONVERTIR LA SEGADORA DESCARGA LATERAL (Vea Fig. 11): Su segadora fue enviada lista para usarse como acolchadora • La puerta trasera tiene que estar cerrada. de capa vegetal. Para convertirla a una operación de ensacado • Abra la protección contra la descarga y instale el desviador o de descarga: de contra la descarga debajo de la protección como se DESCARGA TRASERA (Vea Fig.
Page 31
OPERACIÓN PARA VACIAR EL RECOGEDOR DE CÉSPED TAPA DEL TAPA DEL (Vea Fig. 12) RELLENADOR DEPOSITO DE DE GASOLINA Levante el recogedor de césped usando el mango del bas- ACEITE CON tidor. VARILLA DE NIVEL Remueva el recogedor de césped, con los recortes, de debajo del mango de la segadora.
Page 32
OPERACIÓN • Para un corte muy pesado, reduzca el ancho del corte PARA PARAR EL MOTOR (Vea Fig. 14) pasando parcialmente por encima del lugar anteriormente • Para parar el motor, mueva la control de aceleración/motor cortado y siegue lentamente. a la posición de STOP.
MANTENIMIENTO ANTES DESPUES CADA CADA CADA ANTES DEL DE CADA DE CADA 25 HORAS O ALMACE- HORAS TEMPORADA HORAS NAMIENTO Revisar si hay Sujetadores Sueltos Limpiar/Inspeccionar el Recogedor de Césped * Controlar los Neumáticos Controlar las Ruedas Motrices *** Limpiar la Segadora **** Limpiar debajo la Cubierta de la Transmisión *** Revisar las Correas y las Poleas Impulsadas *** Revisar / Afilar / Cambiar la Cuchilla...
Page 34
MANTENIMIENTO PARA CAMBIAR LA CUCHILLA SEGADORA Ponga la cuchilla en el Embrague de la Cuchilla/Freno. Siempre observe las reglas de seguridad cuando haga el man- tenimiento. Asegúrese de que el borde de salida de la cuchilla (opuesto al borde afi lado) esté hacia arriba hacia el motor. LLANTAS Instale los pernos de la cuchilla en el Embrague de la Cuchilla/ •...
Page 35
MANTENIMIENTO Cambie el aceite después de 25 horas de operación o por lo menos una vez al año si la segadora se utiliza menos 25 horas el año. PRECAUCIÓN: Los solventes de petróleo, tales como el keroseno, no se deben usar Revise el nivel del aceite del cárter antes de arrancar el motor para limpiar el cartucho.
Si su segadora no está funcionando en forma adecuada debido a BAJA problemas que se sospecha vienen del correa de impulsión, lleve su segadora a contacto con su centro de servicio Husqvarna o con un otro centro de servicio cualifi cado para repararla y/o ajustarla. FIG. 20...
IMPORTANTE: NUNCA MANIPULE EL REGULADOR DEL de servicio Husqvarna o con un otro centro de servicio cualifi cado. MOTOR, EL QUE HA SIDO AJUSTADO EN LA FÁBRICA PARA LA VELOCIDAD DEL MOTOR ADECUADA. PUEDE...
Drene el aceite (con el motor caliente) y cámbielo con aceite de motor limpio. (Vea “MOTOR” en la sección de Mantenimiento de este manual.) SOLUCIÓN DE PROBLEMAS Vea la sección apropiada en el manual amenos que esté dirigido a un centro de servico Husqvarna. PROBLEMA CAUSA CORRECCIÓN No arranca Filtro de aire sucio.
Page 39
SOLUCIÓN DE PROBLEMAS Vea la sección apropiada en el manual amenos que esté dirigido a un centro de servico Husqvarna. PROBLEMA CAUSA CORRECCIÓN Falta de Cuchilla desgastada, doblada o suelta. Eleve la altura de corte. fuerza Altura de las ruedas dispareja.
(a) Motores y accesorios.A excepción de los casos en que se indica otra cosa en el Anexo A, todos los motores y accesorios no están cubiertos por esta garantía limitada. En la mayoría de los casos, estos elementos NO han sido fabricados por Husqvarna, en cuyo caso pueden estar cubiertos por separado por la garantía de sus respectivos fabricantes, si tal garantía se proporciona e incluye con el...
Page 41
Si desconoce la ubicación del concesionario de servicio Husqvarna autorizado más cercano, llame a Husqvarna al 1-800-487-5951 de 8:00 a.m. a 8:00 p.m., Hora Estándar del Este, o visite www.husqvarna.com.
Page 42
11. Documentación requerida. Debe conservar y presentar este Comprobante de compra (que incluya la fecha, el modelo del pro- ducto y, si corresponde, el número de serie del motor) a un concesionario de servicio Husqvarna autorizado para obtener el servicio de garantía bajo esta Garantía limitada.
Page 43
RZ – Dos (2) años de garantía al consumidor, piezas y mano de obra, con red de distribuidores Hydro-Gear. EZ – Un (1) año de garantía comercial, piezas y mano de obra, con Husqvarna. Dos (2) años de garantía al consumidor, piezas y mano de obra, con red de distribuidores Hydro-Gear.