SWS Power Tools 66630 Set Up And Operating Instructions Manual

10" heavy-duty 15 amp table saw

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

10" Heavy-Duty 15 aMP

Set uP anD OPerating inStructiOnS

Distributed exclusively by Harbor Freight tools

visit our website at: http://www.harborfreight.com

read this material before using this product.

Failure to do so can result in serious injury.

Save tHiS Manual.

2008 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

table Saw

3491 Mission Oaks Blvd., Camarillo, CA 93011

66630

Table of Contents

Summary of Contents for SWS Power Tools 66630

Page 1: Table Saw
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
Page 2: Important Safety Information
MAKE WORKSHOP KID PROOF with the safety with padlocks, master switches, or by alert symbol, indicates a removing starter keys. hazardous situation which, if not avoided, could result in minor or moderate injury. SKU 66630 For technical questions, please call 1-800-444-3353. Page 2...
Page 3 ALWAYS USE SAFETY GLASSES. mounting, and any other conditions Also use face or dust mask if cutting that may affect its operation. A guard operation is dusty. Everyday eye- SKU 66630 For technical questions, please call 1-800-444-3353. Page 3...
Page 4 Featherboard – A block with “fingers“ that hold the workpiece against the As noted previously, Kickback is a fence while sawing. sudden reaction to a pinched, bound, or misaligned blade, causing an un- SKU 66630 For technical questions, please call 1-800-444-3353. Page 4...
Page 5 Push the wood stock past the blade prior to release. Check guards for proper operation with saw disconnected from power before each use. Do not disable any guard. Do not operate saw if any SKU 66630 For technical questions, please call 1-800-444-3353. Page 5...
Page 6 Must be right angle cut 30°-40° from the angle of the stick to keep hands out of the line of the blade. • The lower lip of the notch must be no longer than the workpiece is thick. SKU 66630 For technical questions, please call 1-800-444-3353. Page 6...
Page 7 These carry important safety designed to filter out microscopic information. If unreadable or miss- particles. (California Health & Safety ing, contact Harbor Freight Tools for a Code § 25249.5, et seq.) replacement. WARNING: Handling the cord on Avoid unintentional starting. Prepare...
Page 8: Grounding Instructions
Check with a qualified electrician or Save tHeSe service personnel if the grounding inStructiOnS. instructions are not completely under- SKU 66630 For technical questions, please call 1-800-444-3353. Page 8...
Page 9 Outlets for 2-Prong Plug.) The outlet must be properly installed and grounded in accordance with all codes and ordinances. Do not use an adapter to connect this tool to a different outlet. SKU 66630 For technical questions, please call 1-800-444-3353. Page 9...
Page 10: Specifications
Make sure there is at least a 1/8” gap before assembling or making between the bottom edge of the Split- any adjustments to the tool. ter and the top surface of the Table SKU 66630 For technical questions, please call 1-800-444-3353. Page 10...
Page 11: Operating Instructions
Locate and mark an 11”-12” square that is centered between the four mounting holes. Once marked, cut out and remove the square. This SKU 66630 For technical questions, please call 1-800-444-3353. Page 11...
Page 12 Tighten the Bevel Lock Knob and be at a 90° angle to the Saw Table then tighten the Bolt (111). and the Bevel Indicator on the Ruler should point to 0°. SKU 66630 For technical questions, please call 1-800-444-3353. Page 12...
Page 13 If the Table Insert is slightly above Miter Gauge slot and adjust the flat the Table, tighten the two Table Insert Bolts until the Table Insert is flush SKU 66630 For technical questions, please call 1-800-444-3353. Page 13...
Page 14 The teeth MUST point down toward the front of the Table Saw for proper operation. See Figure b, above. Incorrect blade installation can damage the Saw Blade, Table Saw and/or workpiece. SKU 66630 For technical questions, please call 1-800-444-3353. Page 14...
Page 15: Work Piece And Work Area Set Up
Switch Box. Support the workpiece properly to The Table Saw is also equipped with avoid pinching. a manual reset overload protector. If the motor shuts off or fails to start SKU 66630 For technical questions, please call 1-800-444-3353. Page 15...
Page 16 Blade from the front of the Saw. PUSH STICK warning! To prevent injury, place (53) hand closest to Blade on the Miter Figure c Gauge Adjusting Knob and keep (view FrOM abOve) SKU 66630 For technical questions, please call 1-800-444-3353. Page 16...
Page 17 Once Blade has made contact with the workpiece, use the hand closer to Fence to guide it. Make sure edge of workpiece re- mains in solid contact with both SKU 66630 For technical questions, please call 1-800-444-3353. Page 17...
Page 18: Maintenance And Servicing
Check the Blade Guard assembly before and after every use. aFter uSe, clean external surfaces of the tool with clean cloth. . SKU 66630 For technical questions, please call 1-800-444-3353. Page 18...
Page 19: Parts List
Miter Gauge Miter Gauge Lock Knob Nut M10 Mat plate Flat washer Column pin Pointer Angle ruler button Steel pipe B Axis flange Push Stick Ruler Screw rod Bolt M6×20 SKU 66630 For technical questions, please call 1-800-444-3353. Page 19...
Page 20: Please Read The Following Carefully
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 66630 For technical questions, please call 1-800-444-3353. Page 20...
Page 21: Assembly Diagram
DiagraM SKU 66630 For technical questions, please call 1-800-444-3353. Page 21...
Page 22: Limited 1 Year / 90 Day Warranty
1 year / 90 Day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.