Drill Master 3150 Assembly And Operation Instructions Manual
  1. Manuals
  2. Brands
  3. Drill Master Manuals
  4. Grinder
  5. 3150
  6. Assembly and operation instructions manual
Drill Master 3150 Assembly And Operation Instructions Manual

Drill Master 3150 Assembly And Operation Instructions Manual

4-1/2" angle grinder
Hide thumbs
Table of Contents

Advertisement

Quick Links

4-1/2" ANGLE GRINDER
Model 03150
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright 2003 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.

Advertisement

Table of Contents
loading

Related Manuals for Drill Master 3150

Summary of Contents for Drill Master 3150

  • Page 1 Copyright 2003 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.

  • Page 2: Product Specifications

    Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. SKU 03150 PAGE 2...

  • Page 3: Electrical Safety

    Do not use a power tool while tired or under the influ- ence of drugs, alcohol, or medication. A moment of inattention while operat- ing power tools may result in serious personal injury. SKU 03150 PAGE 3...
  • Page 4 Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 03150 PAGE 4...

  • Page 5: Specific Safety Rules

    Maintain labels and nameplates on the Polisher/Waxer. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Always wear safety impact eye goggles and heavy work gloves when using this tool. Using personal safety devices reduce the risk for injury.
  • Page 6 (California Health & Safety Code 25249.5, et seq.) WARNING! People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. SKU 03150 PAGE 6...

  • Page 7: Grounded Tools: Tools With Three Prong Plugs

    Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE A SKU 03150 PAGE 7...

  • Page 8: Double Insulated Tools: Tools With Two Prong Plugs

    (See Figure C.) If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) SKU 03150 PAGE 8...
  • Page 9 * Based on limiting the line voltage drop FIGURE C to five volts at 150% of the rated amperes. SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions xxxx/min. per Minute (RPM) SKU 03150 PAGE 9...
  • Page 10 When unpacking, check to make sure all the parts shown on the Parts List on page 12 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.

  • Page 11: Inspection, Maintenance, And Cleaning

    Carbon Brushes in the Brush Holders. Then, replace the Brush Caps. (See Figure D.) Use only a clean cloth and mild detergent to clean the body of the Angle Grinder. Do not use solvents. Do not immerse any part of the tool in liquid. SKU 03150 PAGE 11...

  • Page 12: Please Read The Following Carefully

    Screw Inductor Wood Ruff Key Rubber Bearing Shoe Spindle Ring Screw Wrench Guard NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. REV 04/06 SKU 03150 PAGE 12 REV 11/04...

  • Page 13: Assembly Diagram

    ASSEMBLY DIAGRAM 24, 2, 3 25, 2, 3 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 03150 PAGE 13 REV 04/06...

Table of Contents