LG TV User Manual

LG TV User Manual

32ln54, 37ln54, 39ln54, 42ln54, 47ln54, 50ln54, 55ln54, 60ln54, 32ln565, 32la61, 42la61, 50la61 series tv
Hide thumbs Also See for TV:

Advertisement

SAFETY INSTRUCTIONS

Please read these safety precautions carefully before using the product.
WARNING
y Do not place the TV and/or remote control
y
in the following environments:
- A location exposed to direct sunlight
y
- An area with high humidity such as a
y
bathroom
- Near any heat source such as stoves
y
and other devices that produce heat
- Near kitchen counters or humidifiers
y
where they can easily be exposed to
steam or oil
- An area exposed to rain or wind
y
- Near containers of water such as vases
y
Otherwise, this may result in fire, electric
shock, malfunction or product deformation.
y Do not place the product where it might
y
be exposed to dust.
This may cause a fire hazard.
y Mains Plug is the TV connecting/
y
disconnecting device to AC mains electric
supply. This plug must remain readily
attached and operable when TV is in use.
y Do not touch the power plug with wet
y
hands. Additionally, if the cord pin is wet
or covered with dust, dry the power plug
completely or wipe dust off.
You may be electrocuted due to excess
moisture.
y Make sure to connect Mains cable to
y
compliant AC mains socket with Grounded
earth pin. (Except for devices which
are not grounded on earth.) Otherwise
possibility you may be electrocuted or
injured.
SAFETY INSTRUCTIONS
y Insert power cable plug completely into
y
wall socket otherwise if not secured
completely into socket, fire ignition may
break out.
y Ensure the power cord does not come into
y
contact with hot objects such as a heater.
This may cause a fire or an electric shock
hazard.
y Do not place a heavy object, or the
y
product itself, on power cables.
Otherwise, this may result in fire or electric
shock.
y Bend antenna cable between inside and
y
outside building to prevent rain from
flowing in.
This may cause water damaged inside the
Product and could give an electric shock.
y When mounting TV onto wall make sure
y
to neatly install and isolate cabling from
rear of TV as to not create possibility of
electric shock /fire hazard.
y Do not plug too many electrical devices
y
into a single multiple electrical outlet.
Otherwise, this may result in fire due to
over-heating.
3

Advertisement

Table of Contents
loading

Summary of Contents for LG TV

  • Page 1: Safety Instructions

    SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS Please read these safety precautions carefully before using the product. WARNING y Do not place the TV and/or remote control y Insert power cable plug completely into in the following environments: wall socket otherwise if not secured...
  • Page 2 (thinner or benzene). Fire or electric shock accident can occur. y Do not let your children climb or cling onto the TV. Otherwise, the TV may fall over, y Do not allow any impact, shock or any which may cause serious injury.
  • Page 3 SAFETY INSTRUCTIONS y If any of the following occur, unplug the y If you install the TV on a stand, you need product immediately and contact your to take actions to prevent the product from local service centre. overturning. Otherwise, the product may - The product has been impacted by fall over, which may cause injury.
  • Page 4 Take care not to touch the ventilation Otherwise, this may result in fire, electric openings when watching the TV for long shock or product damage (deformation, periods as the ventilation openings may corrosion or breakage).
  • Page 5 (2 or more hours for LCD, 1 or more hours for Plasma). Also, if you watch the TV at a ratio of 4:3 y Refer all servicing to qualified service for a long time, image sticking may occur personnel.
  • Page 6: Viewing 3D Imaging (Only 3D Models)

    3D contents. distance. Cautions when using the 3D glasses Symptoms which require discontinuation or y Make sure to use LG 3D glasses. Otherwise, refraining from watching 3D contents you may not be able to view 3D videos properly. y Do not watch 3D contents when you feel...
  • Page 7: Installation Procedure

    New features may be added to this TV in the future. y The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned off if it will not be watched for some time, as this will reduce energy consumption.
  • Page 8 ASSEMBLING AND PREPARING Remote control and Owner’s manual Cable holder batteries (AAA) (Depending on model) (See p.25, 26) (See p.19) Power Cord Stand Screws Desk-mount Screw 3EA, P5 x 25 (2EA : Only LA61**) 4EA, M4 x 14 (1EA : Only (Only LN54**, LN565*) 32/37/39/42/47/50/60LN54**, (See p.14)
  • Page 9: Separate Purchase

    Separate purchase items can be changed or modified for quality improvement without any notification. Contact your dealer to buy these items. These devices only work with certain models. AG-F*** AG-F***DP LG Audio Device Cinema 3D glasses Dual play glasses Compatibility LA61**...
  • Page 10: Parts And Buttons

    ASSEMBLING AND PREPARING Parts and buttons Screen Only LA61** SETTINGS INPUT Power indicator and Remote control sensor Speakers Buttons Only LN54**, LN565* Screen SETTINGS Power indicator and INPUT Remote control sensor Speakers Buttons Button Description Scrolls through the saved programmes. Adjusts the volume level.
  • Page 11: Lifting And Moving The Tv

    CAUTION y Avoid touching the screen at all times, as this may result in damage to the screen. y It is recommended to move the TV in the box or packing material that the TV originally came in. y Before moving or lifting the TV, disconnect the power cord and all cables.
  • Page 12: Setting Up The Tv

    ASSEMBLING AND PREPARING Setting up the TV Image shown may differ from your TV. Attaching the stand LA61** 4 EA LN54**, LN565* M4 x 14 P5 x 25 Stand Body Stand Body Stand Base Stand Base M4 x 14 M4 x 14...
  • Page 13: Mounting On A Table

    (This feature is not available for all models.) The Kensington security system connector y When attaching the stand to the TV is located at the rear of the TV. For more set, place the screen facing down on a cushioned table or flat surface to protect information of installation and using, refer to the the screen from scratches.
  • Page 14 <Front> CAUTION Securing the TV to a table (Only LA61**) Fix the TV to a table to prevent from tilting How to fix the TV to a table forward, damage, and potential injury. 1. Connect the Desk-mount Cables to the To secure the TV to a table, insert and tighten Stand Base using the Bracket Screws.
  • Page 15 Insert and tighten the eye-bolts, or TV the television and supporting brackets and bolts on the back of the TV. furniture. - If there are bolts inserted at the eye- » Educating children about the dangers bolts position, remove the bolts first.
  • Page 16: Mounting On A Wall

    37/39/42LN54** Attach an optional wall mount bracket at the rear 32LN565* 42LA61** of the TV carefully and install the wall mount 32LA61** bracket on a solid wall perpendicular to the floor. When you attach the TV to other building VESA (A x B) 200 x 100 200 x 200 materials, please contact qualified personnel.
  • Page 17: Tidying Cables

    Fix the Cable Management firmly to the TV. y If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.
  • Page 18: Making Connections

    MAKING CONNECTIONS MAKING CONNECTIONS Antenna connection Connect the TV to a wall antenna socket with an This section on MAKING CONNECTIONS RF cable (75 Ω). mainly uses diagrams for the LN54** models. Connect various external devices to the TV and switch input modes to select an external device.
  • Page 19: Hdmi Connection

    Transmits the digital video and audio signals Transmits analog video and audio signals from an external device to the TV. Connect the from an external device to the TV. Connect the external device and the TV with the HDMI cable external device and the TV with a component as shown.
  • Page 20: Composite Connection

    Transmits analog video and audio signals Connect a USB storage device such as a USB from an external device to the TV. Connect the flash memory, external hard drive, or a USB external device and the TV with the composite memory card reader to the TV and access the cable as shown.
  • Page 21: Headphone Connection

    You may use an optional external audio system instead of the built-in speaker. Digital optical audio connection Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV with the optical audio cable as shown.
  • Page 22: Mhl Connection

    IN 2 (MHL) port to view the phone screen on the TV. y The MHL passive cable is needed to connect the TV and a mobile phone. y This only works for the MHL-enabled phone. y Some applications can be operated by the remote control.
  • Page 23: Remote Control

    Do not mix old and new batteries, as this may damage the remote control. y In Analogue TV and some countries, some remote control buttons may not work. Make sure to point the remote control toward the remote control sensor on the TV. (Only LA61**) (POWER) Turns the TV on or off.
  • Page 24 EXIT BACK Returns to the previous level. SLEEP EXIT Clears on-screen displays and return to TV viewing. Accesses the AV devices connected with the HDMI cable through HDMI-CEC. Opens the SIMPLINK menu. SLEEP Sets the sleep timer. Control buttons (...
  • Page 25: Using The User Guide

    USING THE USER GUIDE USING THE USER GUIDE User Guide allows you to more easily access the detailed TV information. Press SETTINGS to access the main User Guide OPTION > To set language menus. Press the RED button to access the SETTINGS ...
  • Page 26: Maintenance & Troubleshooting

    Do not use any chemicals as this may damage the product. y Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.
  • Page 27: Environmental Information

    ENVIRONMENTAL INFORMATION ENVIRONMENTAL INFORMATION (India only) WEEE Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the e-waste (Management and Handling) Rules, 2011. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
  • Page 28: Specifications

    SPECIFICATIONS SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. 32LN54** 37LN54** 39LN54** 32LN5400-TA 37LN5400-TA 39LN5400-TA 32LN541B-TB 37LN541B-TB 39LN541B-TB 32LN5420-TC 37LN5420-TC 39LN5420-TC...
  • Page 29 SPECIFICATIONS 55LN54** 60LN54** 32LN565* 55LN5400-TA 60LN5400-TA 55LN541B-TB 60LN541B-TB 55LN5420-TC 60LN5420-TC 55LN542B-TC 60LN542B-TC 55LN5430-TD 60LN5430-TD 55LN543B-TD 60LN543B-TD 55LN5440-TJ 60LN5440-TJ MODELS 55LN544B-TJ 60LN544B-TJ 55LN542Y-TC 60LN542Y-TC 32LN5650-TA 55LN542Z-TC 60LN542Z-TC 55LN543Y-TD 60LN543Y-TD 55LN543Z-TD 60LN543Z-TD 55LN544Y-TJ 60LN544Y-TJ 55LN544Z-TJ 60LN544Z-TJ 55LN541B-TC 60LN541B-TC 55LN541Y-TC 60LN541Y-TC 55LN540B-TA 60LN540B-TA Dimensions With stand (mm) 1250.0 x 790.0 x 297.0...
  • Page 30 Operating Humidity Less than 80 % Storage Temperature -20 °C to 60 °C Storage Humidity Less than 85 % Digital TV Analogue TV New Zealand, Television System DVB-T PAL/SECAM-B/G/D/K, PAL-I Singapore BG : VHF/UHF 1 to 69, CATV 01 to 47...
  • Page 31 SPECIFICATIONS HDMI-DTV supported mode Component port connecting information Horizontal Vertical Component ports on the Resolution Frequency Frequency (kHz) (Hz) 720x480 31.469 59.94 31.5 Video output ports on 720x576 31.25 DVD player 1280x720 37.5 44.96 59.94 1920x1080 33.72 59.94 Signal Component 33.75 480i/576i 28.125...
  • Page 32 SPECIFICATIONS 3D supported mode (Only 3D model) y Video, which is input as below media contents is switched into the 3D screen automatically. y The method for 3D digital broadcast may differ depending on the signal environment. If video is not switched automatically into 3D, manually convert the settings to view 3D images.
  • Page 33: Open Source Software Notice

    In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com.
  • Page 34 (Only DTV) Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. MODEL SERIAL...
  • Page 35: External Control Device Setup

    OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.com...
  • Page 36: Key Codes

    R/C Button Return (BACK) Program Guide R/C Button R/C Button AV (Audio/ Video) Mode ► (Play) R/C Button R/C Button ꕗ (Stop/ Live TV) Caption/Subtitle R/C Button R/C Button ꕘ ( Freeze/Slow Play/Pause) Λ (Arrow Key/ Cursor Up) R/C Button R/C Button ●...
  • Page 37 Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: There are several ways to connect TV based on model’s support port. * Please be advised that not all models support these connectivity.
  • Page 38 You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and RS-232C IN (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. * For other models, connect to the USB port. (PC) (TV) (PC)
  • Page 39: Communication Parameters

    (Colour) 00 to 64 Ratio Temperature 15. ISM 03. Screen (See p.7) Method (Only (See p.8) Mute Plasma TV) 04. Volume 16. Energy 00 to 01 00 to 05 Mute Saving 05. Volume 17. Tune 00 to 64 (See p.8)
  • Page 40: Transmission / Receiving Protocol

    [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
  • Page 41 01 : Screen mute on (Picture off) 10 : Video mute on Ack [d][ ][Set ID][ ][OK/NG][Data][x] * In case of video mute on only, TV will display On Screen Display(OSD). But, in case of Screen mute on, TV will not display OSD.
  • Page 42 * In the standby mode (DC off by off timer or ‘ka’, Transmission [m][a][ ][Set ID][ ][Data 00][ ][Data 01] ‘mc’ command), and if key lock is on, TV will not [ ][Data 02][Cr] turn on by power on key of IR & Local Key.
  • Page 43 * Tune Command Examples: Data 05 : Input Source (Digital) 1. Tune to the analogue terrestrial (PAL) Channel 10. - 02 : Terrestrial TV (DTV) – Use Physical Channel Set ID = All = 00 Number Data 00 & 01 = Channel Data is 10 = 00 0a - 06 : Cable TV (CADTV) –...
  • Page 44 Data 01 & 02 = Major is 17 = 00 11 Data 03 & 04 = Minor/Branch is 1 = 00 01 21. Input select (Command: x b) Data 05 = Digital Terrestrial TV = 02 (Main Picture Input) Total = ma 00 00 00 11 00 01 02 ►...
  • Page 45 08 : Normal Image View (Depending on model) 09 : 3D Mode (Genre) ► To change 3D mode for TV. Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01] [Data 01] It has own range for each 3D option determined by [Data 00].

This manual is also suitable for:

Ln54 seriesLn565 seriesLa61 series55ln5400-ta55ln541b-tb55ln5420-tc ... Show all

Table of Contents