1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Switch
  5. BSX8000-5
  6. Installation instructions manual

Paradyne BSX8000-5 Installation Instructions Manual

Broadband services switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BSX8000-5 Broadband Services Switch
Installation Instructions
Document Number BSX8-A2-GZ40-10
March 2005
Contents

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the "Agreement") will apply to the
software and/or firmware (individually or collectively the "Software") incorporated into the
Paradyne product (the "Product") purchased by you and any derivatives obtained from the
BSX8-A2-GZ40-10
................................................................................................... 3
........................................................................................ 3
.............................................................................................. 6
......................................................................................... 6
................................................................................................... 13
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS,
YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE
PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR
ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
March 2005
...................................................... 1
.......................................................................... 3
......................................................... 4
.................................................................... 5
....................................................................... 5
.......................................................................... 10
......................................................................... 14
............................................................................ 14
................................................. 15
........................................... 15
............................ 4
1

Advertisement

Table of Contents
loading

Related Manuals for Paradyne BSX8000-5

Summary of Contents for Paradyne BSX8000-5

  • Page 1: Table Of Contents

    The terms and conditions of this License Agreement (the “Agreement”) will apply to the software and/or firmware (individually or collectively the “Software”) incorporated into the Paradyne product (the “Product”) purchased by you and any derivatives obtained from the BSX8-A2-GZ40-10 March 2005...
  • Page 2 Paradyne or its authorized distributor or reseller under the following terms and conditions: 1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The Licensee acquires no title, right or interest in the Software other than the license granted under this Agreement.

  • Page 3: Product Documentation Online

    Product Documentation Online Complete documentation for Paradyne products is available at www.paradyne.com. Select Support → Technical Manuals. To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2000. Release Notes Release notes for this product are available in the subscriber firmware area of www.paradyne.com.

  • Page 4: Unpacking And Inspecting The Equipment

    CAUTION: Cover plates should be stored for possible future use. If a MIM is removed from a BSX8000-5, it must be replaced with either another MIM or a cover plate. Do not operate a BSX8000-5 with an open MIM port.

  • Page 5: Installing The Bsx8000-5 In A Blc

    (such as the AIM24000-48) and slots U1 and U2 are reserved for uplink modules. Although not required for operational purposes, if redundancy is desired, two BSX8000-5 modules may be installed in the 12000E, in slots U1 and U2. (Note: For redundancy, the two uplink modules in the chassis must be identical models.)

  • Page 6: Blc Management

    Verify the connection: the Lnk (link) LED on the MIM-2T1 faceplate flashes green to indicate a network connection has been established. BLC Management The BSX8000-5 uplink module provides BLC management capability via the Command Line Interface (CLI), Simple Network Management Protocol (SNMP), and the web-based Network Management System (NMS).
  • Page 7 9. Start your web browser. Type the default IP address into the Address field and press Enter. The default IP address of a BSX8000-5 in Slot 13 of a 12000E BLC or Slot 5 of a 4000E BLC is 192.168.254.252. The default IP address of a BSX8000-5 in Slot 14 of a 12000E BLC is 192.168.254.253.
  • Page 8 The NMS home page appears. March 2005 BSX8-A2-GZ40-10...
  • Page 9 NMS Management Configuration Use the Management Configuration screen to set the unit’s IP address and other management parameters. Procedure To configure management parameters: 1. From the home screen, click on the Management Config button. The Management Configuration screen appears. 2. Select or enter the following parameters: Parameter Description IP Address...

  • Page 10: Command Line Interface (Cli)

    Parameter Description Flood Configuration Flood refers to the method in which interface modules handle unknown unicasts, unknown broadcasts, and unknown multicasts for each port. Uplink – Any traffic with VLAN IDs that match a VLAN ID that has been configured to Uplink flood (default) will be allowed to flow from DSL ports to uplinks only (not DSL port to DSL port).

  • Page 11: Logging Into The Cli

    2. Connect one end of a straight-through RJ45 to RJ45 Ethernet cable into the adapter plugged into your PC, and the other end of the cable into the COM port on the face of the BSX8000-5. Launching the Terminal Emulation Program Launch the terminal emulation program on your PC and configure the program settings.
  • Page 12 Table 1. CLI Commands (2 of 2) Command Description CLEAR_NVRAM If no interface modules are present in the chassis, clears Non-Volatile Random Access Memory, restoring the DSLAM to factory defaults. DISABLE_TELNET Disables access to the DSLAM using Telnet. DISABLE_TFTP Disables access to the DSLAM using Trivial File Transfer Protocol.

  • Page 13: Led Indicators

    BSX8000-5 uplink module is Only one of the BLC power terminals is receiving power connected. No illumination No power The BSX8000-5 uplink module is not receiving power (the BLC may or may not be receiving power). Pulsing green* BSX8000-5 uplink module is operational...

  • Page 14: 10/100/1000Baset Connectors

    10/100/1000BaseT Connectors The uplink ports are 8-pin unkeyed modular jacks for a 10/100/1000BaseT interface. The MGMT port is an 8-pin modular jack supporting 10/100BaseT. Table 3. 10/100/1000 Pinouts Signal Pin 8 Pin 1 Transmitted Data + 97-15449 Transmitted Data – Received Data + Unused Unused...

  • Page 15: Regulatory Compliance For Class A Equipment

    Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to a BSX8000-5 as installed in a Paradyne BLC. US Federal Communications Commission (FCC) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
  • Page 16 *BSX8-A2-GZ40-10* *BSX8-A2-GZ40-10* March 2005 BSX8-A2-GZ40-10...

Table of Contents