1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Desktop
  5. 7387
  6. Hardware maintenance manual

Lenovo 7387 Hardware Maintenance Manual

3000 j series
Hide thumbs Also See for 7387:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Hardware Maintenance Manual
Lenovo 3000 J Series
Types 7387, 7388, 7389, 7390, 7391, 7392,
7393, 7394, 7395, 7396, 7397, 7398

Advertisement

Table of Contents
loading

Related Manuals for Lenovo 7387

Summary of Contents for Lenovo 7387

  • Page 1 Hardware Maintenance Manual Lenovo 3000 J Series Types 7387, 7388, 7389, 7390, 7391, 7392, 7393, 7394, 7395, 7396, 7397, 7398...
  • Page 3 Lenovo 3000 J Series...
  • Page 4 RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in...

  • Page 5: Table Of Contents

    Electrical safety Safety inspection guide . Chapter 8. Replacing FRUs (Types Handling electrostatic discharge-sensitive devices . Grounding requirements . 7387, 7388, 7389, 7393, 7394, and 7395) 83 Safety notices (multi-lingual translations) . Rear connectors . . 84 Removing the covers .
  • Page 6 Recovering from a POST/BIOS update failure . 206 Chapter 10. FRU lists ..147 Power management . . 207 Machine Type 7387 . 148 Automatic configuration and power interface Machine Type 7388 . 156 (ACPI) BIOS .

  • Page 7: Chapter 1. About This Manual

    It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information. See Chapter 2, “Safety information,” on page 3. The Symptom-to-FRU Index and Additional Service Information chapters are not specific to any machine type and are applicable to all Lenovo computers.

  • Page 8: Important Information About Replacing Rohs Compliant Frus

    Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant parts.

  • Page 9: Chapter 2. Safety Information

    After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. v Reinstall all covers correctly before returning the machine to the customer. Electrical safety © Lenovo 2006. Portions © IBM Corp. 2005, 2006.
  • Page 10 Regularly inspect and maintain your electrical hand tools for safe operational condition. v Do not use worn or broken tools and testers. v Never assume that power has been disconnected from a circuit. First, check that it has been powered-off. Lenovo 3000 J Series...

  • Page 11: Safety Inspection Guide

    v Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror.

  • Page 12: Handling Electrostatic Discharge-Sensitive Devices

    – Use the round ground-prong of the ac plug on ac-operated computers. Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Lenovo 3000 J Series...

  • Page 13: Safety Notices (Multi-Lingual Translations)

    Safety notices (multi-lingual translations) The caution and danger safety notices in this section are provided in the following languages: v English v Arabic v Brazilian/Portuguese v Chinese (simplified) v Chinese (traditional) v French v German v Hebrew v Italian v Korean v Spanish DANGER Electrical current from power, telephone and communication cables is hazardous.
  • Page 14 Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) CAUTION: Use safe practices when lifting. Lenovo 3000 J Series...
  • Page 15 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
  • Page 16 Lenovo 3000 J Series...
  • Page 17 Chapter 2. Safety information...
  • Page 18 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) Lenovo 3000 J Series...
  • Page 19 PERIGO A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: v Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. v Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas.
  • Page 20 Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou com instrumentos ópticos e evite exposição direta ao feixe. ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) CUIDADO: Utilize procedimentos de segurança para levantar equipamentos. Lenovo 3000 J Series...
  • Page 21 CUIDADO: O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo de alimentação. Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de alimentação estejam desconectados da fonte de alimentação.
  • Page 22 Lenovo 3000 J Series...
  • Page 23 Chapter 2. Safety information...
  • Page 24 Lenovo 3000 J Series...
  • Page 25 Chapter 2. Safety information...
  • Page 26 3. Branchez les câbles d’interface sur des 3. Débranchez les câbles d’interface des connecteurs. connecteurs. 4. Branchez les cordons d’alimentation sur 4. Débranchez tous les câbles des unités. des prises. 5. Mettez les unités SOUS TENSION. Lenovo 3000 J Series...
  • Page 27 ATTENTION: Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence 33F8354), ou suivre les instructions du fabricant qui en définit les équivalences. Si votre système est doté d’un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
  • Page 28 L’interrupteur de contrôle d’alimentation de l’unité et l’interrupteur dubloc d’alimentation ne coupent pas le courant électrique alimentantl’unité. En outre, le système peut être équipé de plusieurs cordonsd’alimentation. Pour mettre l’unité hors tension, vous devez déconnectertous les cordons de la source d’alimentation. Lenovo 3000 J Series...
  • Page 29 VORSICHT An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen. Aus Sicherheitsgründen: v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen. v Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß...
  • Page 30 Laserstrahlung auftreten. VORSICHT Einige Lasergeräte enthalten eine Laserdiode der Klasse 3A oder 3B. Beachten Sie Folgendes: Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegel verwenden. Strahlungsbereich meiden. Lenovo 3000 J Series...
  • Page 31 ≥18 kg ≥32 kg ≥55 kg ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein. Um die Stromversorgung für die Einheit vollständig zu unterbrechen, müssen alle zum Gerät führenden Netzkabel vom Netz getrennt werden.
  • Page 32 Lenovo 3000 J Series...
  • Page 33 Chapter 2. Safety information...
  • Page 34 Lenovo 3000 J Series...
  • Page 35 PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: v Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. v Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a terra.
  • Page 36 Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener presente quanto segue: Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l’esposizione al fascio. Lenovo 3000 J Series...
  • Page 37 ≥18 kg ≥32 kg ≥55 kg ATTENZIONE: Prestare attenzione nel sollevare l’apparecchiatura. ATTENZIONE: Il pulsante di controllo dell’alimentazione presente sull’unità e l’interruttore dell’alimentatore non disattivano l’alimentazione corrente fornita all’unità. E’ possibile che l’unità disponga di più cavi di alimentazione. Per disattivare l’alimentazione dall’unità, accertarsi che tutti i cavi di alimentazione siano scollegati dalla fonte di alimentazione.
  • Page 38 Lenovo 3000 J Series...
  • Page 39 Chapter 2. Safety information...
  • Page 40 3. Conecte los cables de señal a los 3. Desconecte los cables de señal de los conectores. conectores. 4. Enchufe los cables de alimentación a las 4. Desconecte todos los cables de los tomas de corriente. dispositivos. 5. Encienda el dispositivo. Lenovo 3000 J Series...
  • Page 41 PRECAUCIÓN: Cuando sustituya una batería de litio, utilice solamente una batería número de pieza 33F8354 u otra de tipo equivalente recomendada por el fabricante. Si su sistema dispone de un módulo que contiene una batería de litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La batería contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente.
  • Page 42 Además, el dispositivo podría tener más de un cable de alimentación. Para suprimir toda la corriente eléctrica del dispositivo, asegúrese de que todos los cables de alimentación estén desconectados de la toma de corriente. Lenovo 3000 J Series...

  • Page 43: Chapter 3. General Information

    The Lenovo Care program also contains information to help solve problems and get repair service or other technical assistance. The Lenovo Care program is preinstalled on most Lenovo 3000 J Series products. Additional information resources If you have Internet access, the most up-to-date information for the computer is available from the World Wide Web.

  • Page 44: Specifications

    Specifications This section lists the physical specifications for the computer. Machine types 7387, 7388, 7389, 7393, 7394, and 7395 Dimensions Width: 180 mm (7.09 in.) Height: 392 mm (15.43 in.) Depth: 445 mm (17.52 in.) Weight Minimum configuration as shipped: 9.1kg (20.06 lbs) Maximum configuration: 10.2 kg (22.5 lbs)

  • Page 45: Machine Types 7390, 7391, 7392, 7396, 7397, And 7398

    Machine types 7390, 7391, 7392, 7396, 7397, and 7398 This section lists the physical specifications for the computer. Dimensions Width: 331 mm (13.0 in.) Height: 108 mm (4.3 in.) Depth: 405 mm (15.9 in.) Weight Minimum configuration as shipped: 8.2 kg (18.0 lbs) Maximum configuration: 8.3 kg (18.2 lbs) Environment Air temperature:...
  • Page 46 Lenovo 3000 J Series...

  • Page 47: Chapter 4. General Checkout

    If possible, have this information available when requesting assistance from Service Support and Engineering functions. v Machine type and model v Processor or hard disk upgrades v Failure symptom – Do diagnostics indicate a failure? © Lenovo 2006. Portions © IBM Corp. 2005, 2006.
  • Page 48 7. Have the same configuration options set in the system 8. Have the same setup for the operating system control files Comparing the configuration and software set-up between “working and non-working” systems will often lead to problem resolution. Lenovo 3000 J Series...

  • Page 49: Chapter 5. Diagnostics

    PC-Doctor for DOS Depending upon your machine type and model, you either have PC-Doctor for DOS or PC-Doctor for Windows PE on each Lenovo computer. The PC-Doctor for DOS diagnostic program is part of the Rescue and Recovery workspace and runs independently of the Windows operating system. Use PC-Doctor for DOS, if you are unable to start the Windows operating system or if PC-Doctor for Windows has not been successful in isolating a possible problem.

  • Page 50: Creating A Diagnostic Cd Image

    To create a diagnostic CD image, download a self-starting bootable CD image (known as an .iso image) of the diagnostic program from http:// www.lenovo.com/support/. After you download the image, you can create the CD using any CD burning software. If the computer does not have a CD burner or you do not have Internet access, see “Creating diagnostic diskettes.”...

  • Page 51: Running Diagnostics From The Rescue And Recovery Workspace

    PC-Doctor for Windows PE Depending upon your machine type and model, you either have PC-Doctor for DOS or PC-Doctor for Windows PE on each Lenovo computer. The PC-Doctor for Windows PE diagnostic program is part of the Rescue and Recovery workspace.

  • Page 52: Navigating Through The Diagnostics Programs

    Represents the type of error encountered. v DeviceID: Contains the component’s unit-ID which corresponds to either a fixed disk drive, removable media drive, serial or parallel port, processor, specific RIMM, or a device on the PCI bus. v Date: Lenovo 3000 J Series...

  • Page 53: Fixed Disk Advanced Test (Fdat)

    Contains the date when the diagnostic test was run. The date is retrieved from CMOS and displayed using the YYYYMMDD format. v ChkDigits: Contains a 2-digit check-digit value to ensure the following: – Diagnostics were run on the specified date. –...

  • Page 54: Quick And Full Erase - Hard Drive

    The diagnostics program offers two hard drive format utilities: v Quick Erase Hard Drive v Full Erase Hard Drive The Quick Erase Hard Drive provides a DOS utility that performs the following: v Destroys the Master Boot Record (MBR) on the hard drive. Lenovo 3000 J Series...

  • Page 55: Viewing The Test Log

    v Destroys all copies of the FAT Table on all partitions (both the master and backup). v Destroys the partition table. v Provides messages that warn the user that this is a non-recoverable process. The Full Erase Hard Drive provides a DOS utility that performs the following: v Performs all the steps in Quick Erase.
  • Page 56 Lenovo 3000 J Series...

  • Page 57: Chapter 6. Using The Setup Utility

    Setting, changing, and deleting a user password To set, change, or delete a user password, do the following: Note: A password can be any combination of up to eight characters (A- Z, a-z, and 0-9). © Lenovo 2006. Portions © IBM Corp. 2005, 2006.

  • Page 58: Administrator Or Supervisor Password

    1. From the Setup Utility program menu, select Set Administrator Password orSet Supervisor Password and press Enter. A message will display that indicates the password has been disabled. 2. Press any key to continue. Lenovo 3000 J Series...

  • Page 59: Selecting A Startup Device

    Selecting a startup device If the computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device. Selecting a temporary startup device Use this procedure to startup from any boot device.
  • Page 60 Lenovo 3000 J Series...

  • Page 61: Chapter 7. Symptom-To-Fru Index

    On/Off Switch Power Supply connector v System Board Power Supply connectors v Microprocessor(s) connection Check the power cord for continuity. Power Cord Check the power-on switch for continuity. Power-on Switch © Lenovo 2006. Portions © IBM Corp. 2005, 2006.

  • Page 62: Diagnostic Error Codes

    2. Adapter card 3. System board 000-039-XXX 1. Flash the system. See “Flash update BIOS DMI data error procedures” on page 205 2. System board 000-195-XXX Information only BIOS Test aborted by user Re-start the test, if necessary Lenovo 3000 J Series...

  • Page 63: Procedures

    Diagnostic Error Code FRU/Action 000-196-XXX 1. Press F3 to review the log file BIOS test halt, error threshold exceeded 2. Re-start the test to reset the log file 000-197-XXX 1. Make sure the component that is called BIOS test warning out is connected and/or enabled.

  • Page 64: System Board

    3. Go to “Undetermined problems” on page 001-199-XXX 1. Go to “Undetermined problems” on page System test failed, cause unknown 2. Flash the system and re-test 3. Replace component under function test 001-250-XXX System board System ECC error Lenovo 3000 J Series...
  • Page 65 Diagnostic Error Code FRU/Action 001-254-XXX System board 001-255-XXX 001-256-XXX 001-257-XXX System DMA error 001-260-XXX System board 001-264-XXX System IRQ error 001-268-XXX 1. Device on IRQ1 System IRQ1 failure 2. System board 001-269-XXX 1. Device on IRQ2 System IRQ2 failure 2. System board 001-270-XXX 1.

  • Page 66: System Board

    3. Video card, if installed 4. System board 005-031-XXX 1. Video cable Video Device Cable failure 2. Monitor 3. Video card, if installed 4. System board 005-032-XXX 1. Video card, if installed Video Device Controller failure 2. System board Lenovo 3000 J Series...

  • Page 67: System Board Information Only Re-Start The Test, If Necessary

    Diagnostic Error Code FRU/Action 005-036-XXX 1. Video card, if installed Video Register error 2. System board 005-038-XXX 1. Video card, if installed System BIOS extension failure 2. System board 005-040-XXX 1. Video card, if installed Video IRQ failure 2. System board 005-195-XXX Information only Video Test aborted by user...
  • Page 68 Serial port Test aborted by user Re-start the test, if necessary 011-196-XXX 1. Press F3 to review the log file Serial port test halt, error threshold exceeded 2. Re-start the test to reset the log file Lenovo 3000 J Series...
  • Page 69 Diagnostic Error Code FRU/Action 011-197-XXX 1. Make sure the component that is called Serial port test warning out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4.
  • Page 70 2. Flash the system and re-test. See “Flash allocation failure update procedures” on page 205 3. Run memory test 4. System board 015-035-XXX 1. Remove USB device(s) and re-test USB port Reset condition detected 2. System board Lenovo 3000 J Series...
  • Page 71 Diagnostic Error Code FRU/Action 015-036-XXX System board USB port Register error 015-040-XXX 1. Run setup and check for conflicts USB port IRQ failure 2. Flash the system. See “Flash update procedures” on page 205 3. System board 015-195-XXX Information only USB port Test aborted by user Re-start the test, if necessary 015-196-XXX...
  • Page 72 PCI test warning out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test Lenovo 3000 J Series...
  • Page 73 Diagnostic Error Code FRU/Action 020-198-XXX 1. If a component is called out, make sure PCI test aborted it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures”...
  • Page 74 SCSI interface test warning out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test Lenovo 3000 J Series...
  • Page 75 Diagnostic Error Code FRU/Action 030-198-XXX 1. If a component is called out, make sure SCSI interface test aborted it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and re-test. See “Flash update procedures”...

  • Page 76: Run Setup

    No action Game Port interface Test Passed 080-XXX-XXX 1. Remove the game port device and Game Port interface Error re-test the system 080-195-XXX Information only Game Port interface Test aborted by user Re-start the test, if necessary Lenovo 3000 J Series...

  • Page 77: Information Only

    Diagnostic Error Code FRU/Action 080-196-XXX 1. Press F3 to review the log file Game Port interface test halt, error threshold 2. Re-start the test to reset the log file exceeded 080-197-XXX 1. Make sure the component that is called Game Port interface test warning out is connected and/or enabled.

  • Page 78: Replace The Component That Is Called Out

    1. See “Undetermined problems” on page Microprocessor test failed, cause unknown 2. Flash the system and re-test. See “Flash update procedures” on page 205 3. Replace component under function test 170-000-XXX No action Voltage Sensor(s) Test Passed Lenovo 3000 J Series...
  • Page 79 Diagnostic Error Code FRU/Action 170-0XX-XXX 1. Flash system Voltage Sensor(s) failure 2. System board 170-195-XXX Information only Voltage Sensor(s) Test aborted by user Re-start the test, if necessary 170-196-XXX 1. Press F3 to review the log file Voltage Sensor(s) test halt, error threshold 2.

  • Page 80: System Board No Action

    1. Cache, if removable System Cache error 2. System board 3. Microprocessor 206-000-XXX No action Diskette Drive Test Passed 206-XXX-XXX 1. Diskette Drive Cable Diskette Drive error 2. Check power supply voltages 3. Diskette drive 4. System board Lenovo 3000 J Series...
  • Page 81 Diagnostic Error Code FRU/Action 215-000-XXX No action CD-ROM Drive Test Passed 215-XXX-XXX 1. CD-ROM Drive Cable CD-ROM Drive error 2. Check power supply voltages 3. CD-ROM drive 4. System board 217-000-XXX No action Hard Disk Drive Test Passed 217-25X-XXX 1. Hard Disk Drive Cable 217-26X-XXX 2.
  • Page 82 Diagnostic Error Code FRU/Action 415-000-XXX No action Modem Test Passed 415-XXX-XXX Remove the Modem and re-test the system Modem error Lenovo 3000 J Series...

  • Page 83: Beep Symptoms

    Beep symptoms Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST. The following table describes beep symptoms. Beep Symptom FRU/Action 2 short beeps Perform the following actions in order. CMOS setting error 1.

  • Page 84: Post Error Codes

    This message displays during a full memory test, counting down the memory areas being tested. Memory test fail If POST detects an error during memory testing, additional information appears. This information gives specifics about the type and location of the memory error. Lenovo 3000 J Series...
  • Page 85 POST Error Message Description/Action Press TAB to show POST screen Pressing the TAB key permits the user to toggle between the default POST display screen and a custom POST display screen. Error: Non-System disk or disk error The BIOS was unable to find a suitable boot Replace and press any key when ready device.

  • Page 86: Miscellaneous Error Messages

    Intensity or color varies from left to right of 1. Display characters and color bars 2. Video adapter (if present) 3. System Board No power or fan not running 1. See “Power Supply Problems” on page Lenovo 3000 J Series...

  • Page 87: Undetermined Problems

    Message/Symptom FRU/Action Non-system disk or disk error-type message 1. Diskette Drive with a known-good diagnostic diskette. 2. System Board 3. Diskette Drive Cable Other display symptoms not listed above 1. Display (including blank or illegible display) 2. System Board Power-on indicator or hard disk drive in-use 1.
  • Page 88 3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or adapter. If all devices and adapters have been removed, and the problem continues, replace the system board. Lenovo 3000 J Series...

  • Page 89: Chapter 8. Replacing Frus (Types 7387, 7388, 7389, 7393, 7394, And 7395)

    Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) Important Before you replace any FRU, read Chapter 2, “Safety information,” on page 3. These precautions and guidelines will help you work safely. FRU replacements are to be done by trained service technicians only.

  • Page 90: Rear Connectors

    1. Shut down the operating system, remove any media (DVDs, CDs, or tapes) from the drives, and turn off all attached devices. 2. Unplug all power cords from electrical outlets. Lenovo 3000 J Series...
  • Page 91 4. Remove the two thumb screws at the rear of the left-side cover and slide the cover to the rear to remove. 5. If necessary, remove the right-side cover in the same manner. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 92: Locations

    The following illustration will help you locate the major FRUs in the computer. Heat sink and fan Front panel card Microprocessor Hard disk drive Memory modules System board Optical drive System fan Diskette drive Power supply Lenovo 3000 J Series...

  • Page 93: Identifying Parts On The System Board

    Diskette drive connector PCI Express x16 graphics adapter connector IDE connector 1 PCI Express x1 graphics adapter connector IDE connector 2 System fan connector CMOS battery 12V power connector Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 94: Machine Types 7393, 7394, And 7395

    PCI Express x1 graphics adapter connector Diskette drive connector CMOS battery IDE connector PCI Express x16 graphics adapter connector SATA IDE connectors (2) System fan connector Front panel (power 12V power connector switch/LED) connector Clear CMOS/Recovery jumper Lenovo 3000 J Series...

  • Page 95: Removing And Replacing The Front Bezel

    7. Align the tabs in the chassis and snap it into position. Install the two screws on each side to secure the bezel. 8. Reconnect the power switch/LED cable to the system board. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 96: Replacing A Memory Module

    2 on the socket. Insert the memory module straight down into the connector until it snaps into position and the retaining clips are closed. 5. Go to “Completing the FRU replacement” on page 112. Lenovo 3000 J Series...

  • Page 97: Replacing A Pci Adapter

    5. Install the new adapter into the appropriate PCI connector. 6. Install the screw to secure the new adapter. 7. Go to “Completing the FRU replacement” on page 112. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 98: Replacing The Cmos Battery

    Note: When the computer is turned on for the first time after battery replacement, an error message might be displayed. This is normal after replacing the battery. 9. Go to “Completing the FRU replacement” on page 112. Lenovo 3000 J Series...

  • Page 99: Replacing The Power Supply

    7. Reconnect all power supply cables to the system board and the drives. See “Identifying parts on the system board” on page 87. Make sure the cables are correctly routed. 8. Go to “Completing the FRU replacement” on page 112. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 100: Replacing The System Board (Types 7393, 7394, And 7395)

    8. Remove the four screws 1 securing the heat sink and fan assembly to the system board. 9. Lift the heat sink and fan assembly off the failing system board. Lay the heat sink on its side so that the thermal grease does not come in contact with anything. Lenovo 3000 J Series...
  • Page 101 Note: There will be a black plastic cover on the microprocessor retainer to protect the socket on the new system board. Remove the black plastic Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)
  • Page 102 Insert and tighten the screws that secure the system board. 20. Connect all the cables to the system board. See “Identifying parts on the system board” on page 87. 21. Go to “Completing the FRU replacement” on page 112. Lenovo 3000 J Series...

  • Page 103: Replacing The System Board (Types 7387, 7388, And 7389)

    10. Lift the heat sink and fan assembly off the failing system board. Lay the heat sink on its side so that the thermal grease does not come in contact with anything. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)
  • Page 104 This is important when reinstalling the microprocessor on the new system board. c. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Lenovo 3000 J Series...
  • Page 105 19. Connect all the cables to the system board. See “Identifying parts on the system board” on page 87. 20. Go to “Completing the FRU replacement” on page 112. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 106: Replacing The Microprocessor (Types 7393, 7394, And 7395)

    Notice that there is a retention bracket on the back side of the system board. 5. Lift the heat sink and fan assembly off the failing system board. Lay the heat sink on its side so that the thermal grease does not touch anything. Lenovo 3000 J Series...
  • Page 107 Touch only the sides of the microprocessor. Do not touch the gold contacts on the bottom. 7. Lift the microprocessor 2 straight up and out of the socket. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)
  • Page 108 2 that protects the gold contacts on the new microprocessor 1 . 9. Make sure that the microprocessor retainer is fully open. 10. Lower the microprocessor straight down into the socket. 11. Lock the retainer with the small handle to secure the microprocessor in the socket. Lenovo 3000 J Series...
  • Page 109 14. Connect the heat sink and fan assembly cable to the system board. See “Identifying parts on the system board” on page 87. 15. Go to “Completing the FRU replacement” on page 112. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 110: Replacing The Microprocessor (Types 7387, 7388, And 7389)

    Replacing the microprocessor (Types 7387, 7388, and 7389) 1. Remove the left-side cover. See “Removing the covers” on page 84. 2. Lay the computer on the right side to make the system board and microprocessor accessible. 3. Disconnect the heat sink and fan assembly cable from the system board. See “Identifying parts on the system board”...
  • Page 111 2 that protects the gold contacts on the new microprocessor 1 . 10. Holding the microprocessor with your fingers, position the microprocessor so that the triangle 1 is aligned with the corresponding triangle on the socket. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)
  • Page 112 14. Install the heat sink and fan assembly on the system board. 15. Connect the heat sink and fan assembly cable to the system board. See “Identifying parts on the system board” on page 87. 16. Go to “Completing the FRU replacement” on page 112. Lenovo 3000 J Series...

  • Page 113: Replacing The Primary Hard Disk Drive

    7. Reconnect the signal and power cables to the rear of the hard disk drive. 8. Go to “Completing the FRU replacement” on page 112. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 114: Replacing An Optical Drive

    6. Slide the new drive into the bay until the screws holes on each side are aligned and install two screws in each side of the drive. 7. Reconnect the power cable and signal cable to the new optical drive. 8. Go to “Completing the FRU replacement” on page 112. Lenovo 3000 J Series...

  • Page 115: Replacing The Diskette Drive

    6. Reconnect all signal and power cables that were disconnected. See “Identifying parts on the system board” on page 87. 7. Go to “Completing the FRU replacement” on page 112. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 116: Replacing The Power Switch/ Led Assembly

    6. Reinstall the bezel. See “Removing and replacing the front bezel” on page 89. 7. Reconnect the power switch/LED cable to the system board. 8. Go to “Completing the FRU replacement” on page 112. Lenovo 3000 J Series...

  • Page 117: Replacing The Front Panel Card Assembly

    7. Connect the front USB cable and the front audio cable to the system board. See “Identifying parts on the system board” on page 87. 8. Go to “Completing the FRU replacement” on page 112. Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395)

  • Page 118: Completing The Fru Replacement

    4. If you have replaced the system board, you must update (flash) the BIOS. See “Flash update procedures” on page 205. 5. Some FRU replacements require the configuration to be updated. See Chapter 6, “Using the Setup Utility,” on page 51. Lenovo 3000 J Series...

  • Page 119: Chapter 9. Replacing Frus (Types 7390, 7391, 7392, 7396, 7397, And 7398)

    This chapter does not contain a remove and replace procedure for all FRUs. Only the major FRUs are documented. Note: The computer might look slightly different than the illustrations in this chapter. © Lenovo 2006. Portions © IBM Corp. 2005, 2006.

  • Page 120: Rear Connectors

    6 before opening the cover. To remove the computer cover: 1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down the operating system, and turn off all attached devices. 2. Unplug all power cords from electrical outlets. Lenovo 3000 J Series...

  • Page 121: Locations

    3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. 4. Remove any locking devices such as a padlock that secure the cover. 5. Remove the two screws at the rear of the computer cover and slide the cover to the rear.

  • Page 122: Identifying Parts On The System Board

    Power supply connector Front audio connector Diskette drive connector PCI Express x16 graphics adapter connector IDE connector 1 PCI Express x1 graphics adapter connector IDE connector 2 System fan connector CMOS battery 12V power connector Lenovo 3000 J Series...

  • Page 123: Machine Types 7396, 7397, And 7398

    Machine Types 7396, 7397, and 7398 Microprocessor and heat Front USB connectors (2) sink Microprocessor fan Serial (COM2) connector connector Memory connector 1 Front audio connectors Memory connector 2 PCI adapter connectors (2) Power connector PCI Express x1 graphics adapter connector Diskette drive connector CMOS battery IDE connector...

  • Page 124: Removing And Replacing The Drive Bay Assembly

    1. Remove the computer cover. See “Removing the cover” on page 114. 2. Remove the front bezel by releasing the three tabs and pivoting the top of the bezel outward. 3. Remove the two screws at the front of the chassis securing the drive bay assembly. Lenovo 3000 J Series...
  • Page 125 4. Slide the drive bay assembly forward until it stops. Disconnect the power supply and signal cables from the drives. Pivot the rear of the drive bay assembly upward to remove it completely from the computer. Note: To allow easier access to the cables, lift the fan plenum off the heat sink. See “Locations”...

  • Page 126: Replacing A Memory Module

    6. Replace the drive bay assembly. See “Removing and replacing the drive bay assembly” on page 118. 7. Go to “Completing the FRU replacement” on page 144. Lenovo 3000 J Series...

  • Page 127: Replacing A Pci Adapter

    Replacing a PCI adapter 1. Remove the computer cover. See “Removing the cover” on page 114. 2. Remove the screw that secures the adapter retainer and remove the retainer. 3. Remove the failing adapter. 4. Remove the new adapter from its static-protective package. 5.

  • Page 128: Replacing The Cmos Battery

    Note: When the computer is turned on for the first time after battery replacement, an error message might be displayed. This is normal after replacing the battery. 9. Go to “Completing the FRU replacement” on page 144. Lenovo 3000 J Series...

  • Page 129: Replacing The Power Supply

    Replacing the power supply Attention Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no servicable parts inside these components.
  • Page 130 See “Identifying parts on the system board” on page 116. Make sure the cables are correctly routed. 13. Replace the drive bay assembly. See “Removing and replacing the drive bay assembly” on page 118. 14. Go to “Completing the FRU replacement” on page 144. Lenovo 3000 J Series...

  • Page 131: Replacing The System Board (Types 7396, 7397, And 7398)

    Replacing the system board (Types 7396, 7397, and 7398) Note: When replacing the system board, a new retention bracket for the microprocessor heat sink is required. Make sure you have a new retention bracket before beginning this procedure. 1. Remove the cover. See “Removing the cover” on page 114 2.
  • Page 132 12. Lift the heat sink and fan assembly off the failing system board. Lay the heat sink on its side so that the thermal grease does not come in contact with anything. 13. Lift the small handle 3 and open the retainer 1 . Lenovo 3000 J Series...
  • Page 133 Important Touch only the sides of the microprocessor. Do not touch the gold contacts on the bottom. 14. Lift the microprocessor 2 straight up and out of the socket. Notes: a. Note the orientation of the notches 1 on the microprocessor. This is important when reinstalling the microprocessor on the new system board.
  • Page 134 26. Reinstall any PCI adapter cards that were removed. See “Replacing a PCI adapter” on page 121. 27. Position the fan duct on the heat sink fan. 28. Go to “Completing the FRU replacement” on page 144. Lenovo 3000 J Series...

  • Page 135: Replacing The System Board (Types 7390, 7391, And 7392)

    Replacing the system board (Types 7390, 7391, and 7392) 1. Remove the cover. See “Removing the cover” on page 114. 2. Lift the fan duct off the heat sink fan. 3. Remove any adapter cards installed in the PCI connectors. See “Replacing a PCI adapter”...
  • Page 136 This is important when reinstalling the microprocessor on the new system board. c. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Lenovo 3000 J Series...
  • Page 137 16. Holding the microprocessor with your fingers, position the microprocessor so that the small triangle 1 on one corner is aligned with the corresponding triangle on the socket. 17. Make sure that the small handle is in the raised position. 18.

  • Page 138: Replacing The Microprocessor (Types 7396, 7397, And 7398)

    4. Remove the four screws securing the heat sink and fan assembly to the system board. Notice that there is a retention bracket on the back side of the system board. 5. Lift the heat sink and fan assembly off the failing system board. Lenovo 3000 J Series...
  • Page 139 6. Lift the small handle 3 and open the retainer 1 . Important Touch only the sides of the microprocessor. Do not touch the gold contacts on the bottom. 7. Lift the microprocessor 2 straight up and out of the socket. Chapter 9.
  • Page 140 10. Holding the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are aligned with the tabs in the microprocessor socket. Important To avoid damaging the microprocessor contacts, do not tilt the microprocessor when installing it into the socket. Lenovo 3000 J Series...
  • Page 141 11. Lower the microprocessor straight down into the system board socket of the system board. 12. Lower the microprocessor retainer. 13. Lock the retainer with the small handle to secure the microprocessor in the socket. 14. Use the thermal grease syringe to place five drops of grease on the top of the microprocessor.

  • Page 142: Replacing The Microprocessor (Types 7390, 7391, And 7392)

    “Identifying parts on the system board” on page 116. 4. Rotate handle 1 to release the heat sink clamp and then disengage the clamp from the plastic retention bracket. 5. Lift the heat sink and fan assembly off the system board. Lenovo 3000 J Series...
  • Page 143 6. Lift the small handle 1 . Important Do not touch the gold contacts on the bottom of the microprocessor. If you must touch the microprocessor, touch only the sides. 7. Lift the microprocessor 2 straight up and out of the socket. Notes: a.
  • Page 144 2 that protects the gold contacts on the new microprocessor 1 . 11. Lower the microprocessor straight down into the system board socket of the new system board. 12. Lower and latch the handle to secure the microprocessor in the socket. Lenovo 3000 J Series...
  • Page 145 13. Use the thermal grease syringe to place five drops of grease on the top of the microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the grease syringe). 14. Install the heat sink and fan assembly on the system board. 15.

  • Page 146: Replacing The Hard Disk Drive

    10. Slide the hard disk drive bracket to the right until the screw holes are aligned and install the screws. 11. Reinstall the drive bay assembly and connect the power and signal cables to the drives. 12. Go to “Completing the FRU replacement” on page 144. Lenovo 3000 J Series...

  • Page 147: Replacing An Optical Drive

    Replacing an optical drive 1. Remove the cover. See “Removing the cover” on page 114. 2. Remove the drive bay assembly. See “Removing and replacing the drive bay assembly” on page 118. 3. Remove the screws that secure the drive in the drive bay assembly. 4.

  • Page 148: Replacing The Diskette Drive

    6. Reinstall the drive bay assembly. See “Removing and replacing the drive bay assembly” on page 118. 7. Go to “Completing the FRU replacement” on page 144. Lenovo 3000 J Series...

  • Page 149: Replacing The Power Switch/ Led Assembly

    Replacing the power switch/ LED assembly 1. Remove cover. See “Removing the cover” on page 114. 2. Remove the drive bay assembly. See “Removing and replacing the drive bay assembly” on page 118. 3. Remove the hard disk drive. See “Replacing the hard disk drive” on page 140. 4.

  • Page 150: Replacing The Front Panel Card

    This is a normal sequence to enable the computer to initialize. 1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside the computer. 2. Replace the cover and secure it with two screws. Lenovo 3000 J Series...
  • Page 151 3. Reconnect the external cables and power cords to the computer. See “Rear connectors” on page 114. 4. If you have replaced the system board, you must update (flash) the BIOS. See “Flash update procedures” on page 205. 5. Some FRU replacements require the configuration to be updated. See Chapter 6, “Using the Setup Utility,”...
  • Page 152 Lenovo 3000 J Series...

  • Page 153: Chapter 10. Fru Lists

    “Y“ if the FRU is RoHS compliant or an “N“ if the FRU is not RoHS compliant. Please read “Important information about replacing RoHS compliant FRUs” on page 2 before replacing any FRUs. © Lenovo 2006. Portions © IBM Corp. 2005, 2006.

  • Page 154: Machine Type 7387

    Machine Type 7387 Item 7387 FRUs FRU# Tier RoHS? FRU, Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 Microprocessor, 3800+ Athlon64 AM2 X2 (2.0 GHz processor, 89W) (models 41X4241 21G 21B 22U 22S 22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 25G 26U 26F 27U 27F 28G 21Q 26S 26Y 27S 27Y) Microprocessor, 4200+ Athlon64 AM2 X2 (2.2 GHz processor, 89W) (models...
  • Page 155 Item 7387 FRUs FRU# Tier RoHS? HLDS Combo Model GCC-H20N F/W 1.01 (models 21G 21B 22U 22S 22P 41X7992 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q 9JS 9JP 9JY 9KD 8HS 8HP 8HY 8JD 8KS 8KP 8KY 8SD 9AG 8AG 2BU 2BF 2CS...
  • Page 156 Miscellaneous hardware kit (all models) 41N5334 Cable, hard disk drive and optical drive signal (2-drop) (all models) 41A7875 Card Reader Bezel (all models) 41N5340 7387 Keyboards (USB Preferred - Fullwidth) FRU# Tier RoHS? US English (models 24U 26U 27U 41U 44U) 41A5289...
  • Page 157 7387 Keyboards (USB, Productivity) FRU# Tier RoHS? Arabic (models 21G 25G 28G 45G) 41A4962 Arabic/French (models 21G 25G 28G 45G) 41A4963 Belgian/French (models 21G 25G 28G 45G) 41A4964 Belgian/UK (models 21G 25G 28G 45G) 41A4965 Brazilian (models 22P) 41A4966 Bulgarian (models 21G 25G 28G 45G)
  • Page 158 Internal USB Memory Card Reader (models 24U 24F 24S 24P 24Y 25G 26U 26F 41X2089 28G 42M 42A 42T 43V 44U 44F 45G 26S 26Y 27S 27Y 44S 44Y) Speakers (2-piece) (Lenovo logo) (models 24U 24F 24S 24P 24Y 26U 26F 44U 44F 41A5331 26S 26Y 44S 44Y)
  • Page 159 7387 Windows XP Home Recovery CDs FRU# CRU Tier IT (models 25G 45G) 42Y4316 BR (models 24P) 42Y4317 AE (models 25G 45G) 42Y4318 RU (models 25G 45G) 42Y4319 SV (models 25G 45G) 42Y4320 DK (models 25G 45G) 42Y4321 FI (models 25G 45G)
  • Page 160 Hong Kong - TC (models 21B) 42T8702 Multilingual 1 (models 21G 28G) 42Y4427 Multilingual 2 (models 21G 28G) 42Y4428 7387 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier US (models 9FU 9HU 2BU 4AU 9BG) 87H4730 FR/CF (models 9FF 9HF 2BF 4AF 9BG)
  • Page 161 7387 Vista Business 32 Recovery DVDs FRU# CRU Tier DK (Models 8DG) 87H4785 NL (Models 8DG) 87H4786 CZ (Models 8DG) 87H4787 FI (Models 8DG) 87H4788 PL (Models 8DG) 87H4789 RU (Models 8DG) 87H4790 TR (Models 8DG) 87H4791 HU (Models 8DG)

  • Page 162: Machine Type 7388

    HLDS RoHS RAMBO-8 drive (models 21G 22G 23G) 42Y9371 PBDS/Lite-ON Rambo 8 (models 21G 22G 23G) 42Y6017 PATA RAMBO-8 RoHS SW-9587 (VISTA FW) (models 21G 22G 23G) 42Y9370 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 21G 22G 23G) 43C0144 Diskette drive, w/bezel (models) Lenovo 3000 J Series...
  • Page 163 Item 7388 FRUs FRU# Tier RoHS? Front panel card (USB/Audio) assembly (all models) 41N5330 Hard disk drive, 250GB, 7200rpm, serial ATA (models 21G 22G 41G) 40Y9036 System board, nVidia C51g (models 21G 22G 5AG 6AG 5BG 6BG) 87H4658 System Fan, rear w/grill (all models) 41N5339 Power supply, 280W, ATX, Standard (models 21G 22G 41G) 41N3479...
  • Page 164 Power Cord (Switzerland) (models 21G 22G41G) 39M5157 Power Cord (Israel) (models 21G 22G41G) 39M5171 Power Cord (South Africa) (models 21G 22G41G) 39M5143 7388 Windows XP Home Recovery CDs FRU# CRU Tier US/UK/AP/TH (models 21G 41G) 42Y3480 Lenovo 3000 J Series...
  • Page 165 7388 Windows XP Home Recovery CDs FRU# CRU Tier RE (models 21G 41G) 42Y3486 FR/CF (models 21G 41G) 42Y3413 GR (models 21G 41G) 42Y4314 SP/LA (models 21G 41G) 42Y4315 IT (models 21G 41G) 42Y4316 AE (models 21G 41G) 42Y4318 RU (models 21G 41G) 42Y4319 SV (models 21G 41G) 42Y4320...
  • Page 166 JP (models 6BG) 87H4782 NO (models 6BG) 87H4783 SV (models 6BG) 87H4784 DK (models 6BG) 87H4785 NL (models 6BG) 87H4786 CZ (models 6BG) 87H4787 FI (models 6BG) 87H4788 PL (models 6BG) 87H4789 RU (models 6BG) 87H4790 Lenovo 3000 J Series...

  • Page 167: Machine Type 7389

    7388 Vista Business 32 Recovery DVDs FRU# CRU Tier TR (models 6BG) 87H4791 HU (models 6BG) 87H4792 GK (models 6BG) 87H4793 PO (models 6BG) 87H4794 SL (models 6BG) 87H4798 7388 Corel Education CDs FRU# Tier RoHS? US (models 22U 22M 24U 26U 27U 41U 42M 42A 42T 44U) 41X0440 CF (models 24F 26F 27F 41F 44F) 41X0443...
  • Page 168 7389 Keyboards (USB, Productivity) FRU# Tier RoHS? US English (models 41M 41A) 41A4961 Hong Kong/Taiwan (models 42V) 41A4968 7389 mice FRU# Tier RoHS? Mouse, USB Optical Wheel (all models) 41A5085 Mouse, USB Optical Wheel - Logitec (all models) 41A5089 Lenovo 3000 J Series...
  • Page 169 7389 Adapters and miscellaneous FRUs FRU# Tier RoHS? ATI X300SE 128MB (models 41M 41A 42V) 39J9635 Internal USB Memory Card Reader (models 41M 41A 42V) 41X2089 7389 Power Cords FRU# Tier RoHS? Power Cord (US) (models 41A) 39M5080 Power Cord (Australia/New Zealand) (models 41M) 39M5102 Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 41A) 39M5150...

  • Page 170: Machine Type 7390

    PO (models 6BG) 87H4794 SL (models 6BG) 87H4798 7389 Corel Education CDs FRU# CRU Tier US (models 41M 41A) 41X0440 Machine Type 7390 Item 7390 FRUs FRU# Tier RoHS? Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 Lenovo 3000 J Series...
  • Page 171 Item 7390 FRUs FRU# Tier RoHS? Microprocessor, 3800+ Athlon64 AM2 X2 (2.0 GHz processor, 89W) 41X4241 (models 21B 21V 21J 22M 22Q 22H) Microprocessor, 4200+ Athlon64 AM2 X2 (2.2 GHz processor, 89W) 41X1421 (models 41B 42H) Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 21V 21J 22M 41X3547 22Q 22H) Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 21V 21J 22M...
  • Page 172 41D2781 Internal USB Memory Card Reader (models 21B 21V 21J 22M 22Q 22H 41B 42H) 41X2089 Speakers (2-piece) (Lenovo logo) (models 21B 21V 21J 22M 22Q 22H) 41A5334 Speakers (2-piece) (Lenovo logo) (models 21B 21V 21J 22M 22Q 22H) 41A5331...
  • Page 173 7390 Power Cords FRU# Tier RoHS? Power Cord (Japan) (models 21J) 39M5193 Power Cord (Australia / New Zealand) (models 22M) 39M5102 Power Cord (Hong Kong) (models 21B 22H 41B) 39M5151 Power Cord (Taiwan) (models 21V) 39M5246 Power Cord (South Africa) (models 22M) 39M5143 Power Cord (India) (models 22Q) 39M5004...

  • Page 174: Machine Type 7392

    Memory module, 512MB PC2-4200 -533MHz - DDR2 SDRAM (models 21B 41X4251 22H) System board, nVidia C51g (models 21B 22H) 87H4658 Power supply, 220W TFX ; Robust (models 21B 22H) 41N3493 The FRUs listed in the following table are not illustrated. Lenovo 3000 J Series...
  • Page 175 7392 Adapters and miscellaneous FRUs FRU# Tier RoHS? Internal USB Memory Card Reader (models 21B 22H) 41X2089 Speakers (2-piece) (Lenovo logo) (models 21B 22H) 41A5334 Speakers (2-piece) (Lenovo logo) (models 21B 22H) 41A5331 Speaker Power brick - China, Thailand (models 21B 22H) 89P8581...
  • Page 176 SP/LA (models) 87H4756 BR (models) 87H4757 IT (models) 87H4758 RE (models) 43C0613 JP (models) 87H4759 NO (models) 87H4760 SV (models) 87H4761 DK (models) 87H4762 NL (models) 87H4763 CZ (models) 87H4764 FI (models) 87H4765 PL (models) 87H4766 Lenovo 3000 J Series...
  • Page 177 7392 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier RU (models) 87H4767 TR (models) 87H4768 HU (models) 87H4769 GK (models) 87H4770 PO (models) 87H4771 TW (models) 87H4772 HK (models) 87H4773 KR (models) 87H4774 SL (models) 87H4775 7392 Vista Business 32 Recovery DVDs FRU# CRU Tier US/UK/AP/TH (models)

  • Page 178: Machine Type 7393

    Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 22U 22F 23V 24U 41X3547 24F 55U 55F 55S 55P 55Y 22Q 94H 95B EAS EAP EAY F7D F8S F8P F8Y G4S G4P G4Y G5D H6S H6P H6Y H7D 5JS 5JP 5JY HAD) Lenovo 3000 J Series...
  • Page 179 Item 7393 FRUs FRU# Tier RoHS? Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 22U 22F 23V 24U 41X3548 24F 55U 55F 55S 55P 55Y 22Q 94H 95B EAS EAP EAY F7D F8S F8P F8Y G4S G4P G4Y G5D H6S H6P H6Y H7D 5JS 5JP 5JY HAD) Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 22U 22F 23V 24U 41X3549...
  • Page 180 GYP GLS GLY 5MD 5JS 5JP 5JY HAD HBY HCD HDS HDP HES 6GU 6GF 6HU 6HF 8MV 8MK 8AM 8AQ 8JU 8JF 8KU 8KF HDS HDY HFD) Note: When you order a new system board you must also order a new retention bracket for the heat sink. Lenovo 3000 J Series...
  • Page 181 Item 7393 FRUs FRU# Tier RoHS? System board, 946GZ D (models 21U 21F 22U 22F 23V 24U 24F 26U 26F 43C3505 27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G 57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B 2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5AY 5BU 5BF 5CU 5CF 5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA 8AT 99V 97M 98B 98H E1S E1P E1Y E2D E3S E3Y E4P E5D E6P E7S E7Y E8D EAS...
  • Page 182 Swiss F/G (models 25G 52G 57G 58G 91G) 41A4993 Thailand (models 51T) 41A4994 Turkish 440 (models 25G 52G 57G 58G 91G) 41A4995 Turkish 179 (models 25G 52G 57G 58G 91G) 41A4996 UK English (models 25G 52G 57G 58G 91G) 41A4997 Lenovo 3000 J Series...
  • Page 183 24S 24P 24Y 25G 27F 51U 51F 51M 51A 51T 52G 56U 56F 57G 57V 58G 22Q 27S 27Y 51S 51Y 56S 56Y 91G 92M 93V) Speakers (2-piece) (Lenovo logo) (models 24U 24F 24S 24P 24Y 27F 56U 56F 27S 41A5331...
  • Page 184 SP/LA (models 21S 21Y 22S 22Y 52G 55S 55Y 57G 26S 26Y 51S 51Y 91G) 42Y4195 IT (models 52G 57G 91G) 42Y4196 BR (models 52G 55P) 42Y4197 AE (models 52G 57G 91G) 42Y4198 RU (models 52G 57G 91G) 42Y4199 Lenovo 3000 J Series...
  • Page 185 7393 Windows XP Pro Recovery CDs FRU# CRU Tier SV (models 52G 57G 91G) 42Y4200 DK (models 52G 57G 91G) 42Y4201 FI (models 52G 57G 91G) 42Y4202 NO (models 52G 57G 91G) 42Y4203 NL (models 52G 57G 91G) 42Y4204 CZ (models 52G 57G 91G) 42Y4205 HE (models 52G 57G 91G) 42Y4206...

  • Page 186: Machine Type 7394

    98B 98H G2U G2F G3H G8B H3S H3Y H4P H5D G2V G2K GBM GBA GBQ GBT GDU GDF GEU GEF HBY HCD HDS HDP HDY HFS 6HU 6HF 8MV 8MK 8A 8AQ 8KU 8KF HDS HDY HFD) Lenovo 3000 J Series...
  • Page 187 Item 7394 FRUs FRU# Tier RoHS? PBDS/Lite-ON Rambo 8 (models 26U 26F 27U 27F 51U 51F 51M 51A 51T 42Y6017 52G 56U 56F 57G 57V 58G 51S 51Y 56S 56Y 92M 93V 28G 61G 59S 59Y 59P 5AS 5AY 5DU 5DF 5KA 5KQ 5KT 5KV 6AU 6AF 8AU 8AF 99V 97M 98B 98H G2U G2F G3H G8B H3S H3Y H4P H5D G2V G2K GBM GBA GBQ GBT GDU GDF GEU GEF HBY HCD HDS HDP HDY HFS 6HU 6HF 8MV 8MK 8A 8AQ 8KU 8KF HDS HDY HFD)
  • Page 188 US Euro (models 21G 41G 42G 91G) 41A4998 Slovenian (models 21G 41G 42G 91G) 41A4999 7394 mice FRU# Tier RoHS? Mouse, USB Optical Wheel (all models) 41A5085 Mouse, USB Optical Wheel - Logitec (all models) 41A5089 Lenovo 3000 J Series...
  • Page 189 7394 Adapters and miscellaneous FRUs FRU# Tier RoHS? L1 IEEE 1394 PCI Adapter (models 21G 41G) 41D2781 ATI X300SE 128MB (models 42G 91G) 39J9635 ATI X700 PRO 128MB (models 41G) 39J6203 Internal USB Memory Card Reader (models 21G 41G 42G 91G) 41X2089 7394 Power Cords FRU#...
  • Page 190 42Y4210 GK (models 42G 91G) 42Y4211 SL (models 42G 91G) 42Y4212 Multilingual 1 (models 42G 91G) 42Y4427 Multilingual 2 (models 42G 91G) 42Y4428 7394 Vista Business 32 Recovery DVDs FRU# CRU Tier US/UK/AP/TH (models 94A) 87H4776 Lenovo 3000 J Series...

  • Page 191: Machine Type 7395

    Machine Type 7395 Item 7395 FRUs FRU# Tier RoHS? FRU, Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 models) Microprocessor, Intel 820 - A0 Smithfield (models 21M 21A 22V) 41T1704 Microprocessor, Intel 925 (models 41B 42H 43M 43A 44V) 41X2413 Microprocessor, CONROE E6300 1066/1860MHZ-2M (models 91S 91P 91Y 41X2495...
  • Page 192 7395 FRUs FRU# Tier RoHS? Cable, SATA 250mm (all models) 41A7145 Luxshare SATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1186 IDE cable for Tower (2-drop) (all models) 41A7140 Modem Phone Cable (all models) 39K5120 Lenovo 3000 J Series...
  • Page 193 7395 FRUs FRU# Tier RoHS? Cable, diskette drive (RoHs) (all models) 41A7130 Mechanical kit, side cover (all models) 41N5333 Mechanical kit (all models) 41N5331 Main bezel kit (all models) 41N5283 Power switch/LED assembly (all models) 41N5284 Shield, system board (945GZ) (all models) 41N5286 Miscellaneous hardware kit (all models) 41N5334...
  • Page 194 87H4789 RU (models 49G 99G) 87H4790 TR (models 49G 99G) 87H4791 HU (models 49G 99G) 87H4792 GK (models 49G 99G) 87H4793 PO (models 49G 99G) 87H4794 HK (models 49G 99G) 87H4796 SL (models 49G 99G) 87H4798 Lenovo 3000 J Series...

  • Page 195: Machine Type 7396

    7395 Corel Education CDs FRU# CRU Tier US (models 21M 21A 42H 43M 43A) 41X0440 Machine Type 7396 Item 7396 FRUs FRU# Tier RoHS? Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 models) Microprocessor, Intel 820 - A0 Smithfield (models 21M 21A 21Q 21T 21H 41T1704 22G 22V 23G 24B 25H) Microprocessor, Intel 925 (models 41M 42G)
  • Page 196 The FRUs listed in the following table are not illustrated. 7396 FRUs FRU# Tier RoHS? Modem Phone Cable (all models) 39K5120 Shield, EMC, 5.25in. drive bay (all models) 41A7162 Cable, Serial-ATA, (18in. RoHs) (all models) 41A7145 Shield, EMC, diskette drive bay (all models) 41A7146 Lenovo 3000 J Series...
  • Page 197 7396 FRUs FRU# Tier RoHS? Cable, diskette drive (all models) 41A7147 Cover (all models) 41A7148 Chassis Kit Assembly with bezels (all models) 41N5251 Bezel Assembly kit (all models) 41N5268 Fan duct assembly (all models) 41A7151 Fan duct assembly (all models) 41R4808 Shield, EMC, system board (all models) 41N5347...
  • Page 198 41A5265 Hungarian (models 42G) 41A5266 Iceland (models 42G) 41A5267 Italian 141 (models 42G) 41A5268 Norwegian (models 42G) 41A5272 Polish (models 42G) 41A5273 Portuguese (models 42G) 41A5274 Romanian 446 (models 42G) 41A5275 Romanian 96 (models 42G) 41A5276 Lenovo 3000 J Series...
  • Page 199 7396 Keyboards (Fingerprint Reader, USB) FRU# Tier RoHS? Russian/Cy (models 42G) 41A5277 Serbian/Cyrillic (models 42G) 41A5278 Slovak (models 42G) 41A5279 Spanish (models 42G) 41A5280 Swedish/Finn (models 42G) 41A5281 Swiss F/G (models 42G) 41A5282 Turkish 179 (models 42G) 41A5284 Turkish 440 (models 42G) 41A5285 UK English (models 42G) 41A5286...
  • Page 200 US/UK/AP/TH (models 44H 9BH) 87H4753 HK (models 44B 9BB) 87H4773 7396 Vista Business 32 Recovery DVDs FRU# CRU Tier US/UK/AP/TH (models 8AG 8BG 27M 43M 5CM 5AA) 87H4776 FR/CF (models 8AG 8BG) 87H4777 GR (models 8AG 8BG) 87H4778 Lenovo 3000 J Series...

  • Page 201: Machine Type 7397

    7396 Vista Business 32 Recovery DVDs FRU# CRU Tier SP/LA (models 8AG 8BG) 87H4779 IT (models 8AG 8BG) 87H4781 RE (models 8AG 8BG) 43C0615 NO (models 8AG 8BG) 87H4783 SV (models 8AG 8BG) 87H4784 DK (models 8AG 8BG) 87H4785 NL (models 8AG 8BG) 87H4786 CZ (models 8AG 8BG) 87H4787...
  • Page 202 Note: When you order a new system board you must also order a new retention bracket for the heat sink. Power supply, 220W TFX ; Standard (models 23G) 41N3109 Power supply, 220W TFX ; Japan (models 21J 22J 41J 42J) 41N3119 Lenovo 3000 J Series...
  • Page 203 7397 FRUs FRU# Tier RoHS? Modem Phone Cable (all models) 39K5120 Shield, EMC, 5.25in. drive bay (all models) 41A7162 Cable, Serial-ATA, (18in. RoHs) (all models) 41A7145 Shield, EMC, diskette drive bay (all models) 41A7146 Cable, diskette drive (all models) 41A7147 Cover (all models) 41A7148 Chassis Kit Assembly with bezels (all models)
  • Page 204 Power Cord (Denmark) (models 23G) 39M5129 Power Cord (Switzerland) (models 23G) 39M5157 Power Cord (Israel) (models 23G) 39M5171 Power Cord (South Africa) (models 23G) 39M5143 7397 Windows XP Pro Recovery CDs FRU# CRU Tier US/UK/AP/TH (models 23G) 42Y3466 Lenovo 3000 J Series...
  • Page 205 7397 Windows XP Pro Recovery CDs FRU# CRU Tier RE (models 23G) 42Y3473 FR/CF (models 23G) 42Y4193 GR (models 23G) 42Y4194 SP/LA (models 23G) 42Y4195 IT (models 23G) 42Y4196 AE (models 23G) 42Y4198 RU (models 23G) 42Y4199 SV (models 23G) 42Y4200 DK (models 23G) 42Y4201...

  • Page 206: Machine Type 7398

    GK (models 8BG) 87H4793 PO (models 8BG) 87H4794 SL (models 8BG) 87H4798 7387 Corel Education CDs FRU# CRU Tier US (models 22U 22M 24U 26U 27U 41U 42M 42A 42T 44U) 41X0440 CF (models 24F 26F 27F 41F 44F) 41X0443...
  • Page 207 Item 7398 FRUs FRU# Tier RoHS? HLDS RoHS RAMBO-8 drive (models 41M 42V 91H 92H 93B 94B 97M 95A 42Y9371 95T 96B 96H) PBDS/Lite-ON Rambo 8 (models 41M 42V 91H 92H 93B 94B 97M 95A 95T 42Y6017 96B 96H) HLDS RAMBO-8 GSA-H10N F/W JX07 (models 41M 42V 91H 92H 93B 43C0144 94B 97M 95A 95T 96B 96H) Power switch/LED assembly (all models)
  • Page 208 US/UK/AP/TH (models 91H) 42Y3480 Hong Kong - TC (models 91B) 7398 Windows XP Pro Recovery CDs FRU# CRU Tier US/UK/AP/TH (models 41M 92H) 42Y3466 Taiwan - TC (models 42V) 42T8695 Hong Kong - TC (models 82B) Lenovo 3000 J Series...
  • Page 209 7398 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier US/UK/AP/TH (models 96B) 87H4730 HK (models 96H) 87H4750 7398 Vista Business 32 Recovery DVDs FRU# CRU Tier US/UK/AP/TH (models 97M 95A) 87H4776 7398 Corel Education CDs FRU# CRU Tier US (models 41M) 41X0440 Chapter 10.
  • Page 210 Lenovo 3000 J Series...

  • Page 211: Chapter 11. Additional Service Information

    2. Lenovo Customer Support Center 3. Levels 1 and 2 Support To update (flash) the BIOS, see “Flash update procedures.” Flash update procedures This section details how to flash (update) the BIOS. © Lenovo 2006. Portions © IBM Corp. 2005, 2006.

  • Page 212: Updating (Flashing) Bios From A Diskette

    Updating (flashing) BIOS from a diskette 1. Insert a system program update (flash) diskette into the diskette drive. system program updates are available at http://www.lenovo.com/support on the World Wide Web. 2. Turn on the computer. If it is already on, you must turn it off and back on. The update begins.

  • Page 213: Power Management

    Power management Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors. Automatic configuration and power interface (ACPI) BIOS Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored.

  • Page 214: Recovering Software

    The set of Product Recovery discs will enable the contents of the hard disk to be restored to the same state as when the computer was originally shipped from the factory. For more information on recovering factory-installed software, refer to “Recovering software” in the User Guide. Lenovo 3000 J Series...

  • Page 215: Appendix. Notices

    Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.

  • Page 216: Television Output Notice

    Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Lenovo logo...
  • Page 218 Part Number: 41X8137 Printed in USA (1P) P/N: 41X8137...

This manual is also suitable for:

738873897392739373947390 ... Show all

Table of Contents