Philips 55PFS8159 User Manual page 71

press OK.
4. Select Ambilight+hue one step further, select On and
press OK.
5. Select Configure Ambilight+hue and press OK.
If the TV is connected to your home network, it will start
looking for the Philips hue bridge immediately.
If the TV is not yet connected to your network, the TV
will start the network setup first. You must connect the
TV to your home network.
With the TV connected to your network, go to page Hue
bridge.
For more info on connecting the TV to your home network,
î„"
press Keywords and look up Network, wireless.
Hue bridge
In the following step, you will link up the TV with the Philips hue
bridge.
The TV can only be linked up to one hue bridge.
To link the hue bridge...
1. With the TV connected to the network, it will show the
available hue bridges. If the TV did not find your hue
bridge yet, you can select Scan again and press OK.
If the TV found the only hue bridge you have, select
Next and press OK.
If you have more than one hue bridge available, press
 (up) or  (down) to select the hue bridge you want
to use and then select Next and press OK.
2. After you pressed OK, go to the Philips hue bridge and
press the link button in the middle of the device. This will
link the hue bridge with the TV. Do this within 30
seconds. The TV will confirm if a hue bridge is linked to
the TV.
3. On this confirmation, select OK and press OK.
With the Philips hue bridge linked to the TV, go to page Hue
bulbs.
Hue bulbs
In the following step, you will select the Philips hue bulbs that
have to follow the Ambilight.
You can select a maximum of 9 Philips hue bulbs for
Ambilight+hue.
To select the bulbs for Ambilight+hue...
1. In the Configure Ambilight+hue menu, select Hue bulbs
and press OK.
2. Mark the bulbs that have to follow the Ambilight. To
mark a bulb, select the bulb name and press OK.
3. When you're done, select the OK button and press OK.
With the bulbs marked for Ambilight+hue, go to page Configure
bulb.
Configure bulb
In the following step, you will configure each Philips hue bulb.
To configure each hue bulb...
1. Select the bulb name in the Configure Ambilight+hue
menu and press OK. The bulb you selected is blinking.
2. First indicate where you placed the bulb relative to the
TV. A correct setting of the Angle will send the correct
Ambilight colour to the bulb. Press  (up) or  (down)
to adjust.
3. Press  (right) to set the distance.
4. Secondly, indicate the Distance between the bulb and
the TV. The further away from the TV, the weaker the
Ambilight colour. Press  (up) or  (down) to adjust.
5. Press  (right) to set the brightness.
6. Finally, set the Brightness of the bulb. Press  (up) or
î„Ž (down) to adjust.
7. To stop configuring this bulb, select OK and press OK.
8. In the Configure Ambilight+hue menu, you can select
every bulb and do the same.
9. When all Ambilight+hue bulbs are configured, select
Finish and press OK.
Ambilight+hue is ready for use.
You can always change the Ambilight+hue configuration later.
To change the configuration, press î‚¥ and select Setup > TV
settings > Ambilight > Ambilight+hue.
Immersion
With Immersion, you can adjust the level of the Ambilight effect
for the Ambilight+hue bulbs.
To adjust the Ambilight+hue Immersion...
1. Press î‚¥ and select Setup and press OK.
2. Select TV settings > Ambilight > Ambilight+hue >
Immersion and press OK.
3. Press  (up) or  (down) to adjust.
4. Pressî‚šî‚š, repeatedly if necessary, to close the menu.
.
Info
In View configuration, you can consult the current
Ambilight+hue configuration. Which network you use, how
many bulbs are connected, etc.
To view the current Ambilight+hue setup...
1. Press  and select Setup and press OK.
71