Setting Clock Time; Setting And Using The Alarms; Dimmer Control - Sharper Image EC-B145 Instruction Manual

Setting Clock Time:

1. Press TIME SET button located on the top panel of unit, HOUR will be flashing.
Press the SET+ / SET - button to select hour.
2. Press TIME SET button again, MINUTE will be flashing. Press the SET + / SET -
button to select minute.
3. If the time showing is not correct, please press the TIME SET button again to
repeat steps 1 and 2.

Setting and Using the Alarms:

Setting Alarm1 or Alarm2 (Individually)
1. Press the AL1 / AL2 button on the unit, the al1 or al2 icon will appear on the
display to indicate which alarm is activated.
2. Press the AL SET button, HOUR digit will begin flashing. Press the SET + / SET
- button until the desired hour is displayed.
3. Press the AL SET button again, MINUTE digits will begin flashing. Press the
SET + / SET - button until the desired minute is displayed.
4. Press the AL SET button again to exit the alarm setting mode or the display will
stop flashing after 5 seconds to indicate the alarm is set.
5. Toggle through the AL MODE button until the corresponding LED light
illuminates next to the wake mode of your choice: iPod/iPhone, Radio, or Beep
tone.
6. When the alarm is sounding, press the POWER button on the unit to turn the
alarm OFF. The alarm will automatically sound the next day at the same time.
7. To STOP the alarm from sounding the next day, press the AL 1 / AL 2 button
to the OFF position. The al1 or al2 icon will disappear on the LCD display to
indicate the alarm is disarmed.
Setting Alarm1 and Alarm2 (Together)
1. Press the AL 1 / AL 2 button on the unit, the al1 and al2 icon will appear on the
display to indicate BOTH alarms are activated.
Note: You cannot change the alarm time when BOTH are selected.
If you need to change the alarm time for either alarm, follow step 1 under
"Setting Alarm1 or Alarm 2" (Individually).
8
2. Toggle through the AL MODE button until the corresponding LED light
illuminates next to the wake mode of your choice: iPod/iPhone, Radio or Beep
tone. Both al1 and al2 must wake to the same mode.
Note: To wake to iPod/iPhone, your iPod/iPhone must be properly docked in
the unit or it will default to beep tone wake mode.
3. When the alarm is sounding, press the POWER button to turn the alarm OFF.
The alarm will automatically sound the next day at the same time.
4. To stop the alarm from sounding the next day, press the al1 / al2 button to
the OFF position. The al1 and al2 icons will disappear on the LCD display to
indicate the alarms are disarmed.
Refer to Fig. 2.
Snooze Operation:
Press the SNOOZE/NAP bar after the alarm sounds. The alarm will be silenced
and return 9 minutes later. Snooze can be pressed several times during the 1
hour alarm cycle. You may use this feature until you turn the alarm OFF.
Nap Operation:
The Nap function will wake you after a nap of 15, 30, 45 or 60 minutes – without
the need to change your regular al1 or al2 settings.
1. If the system is playing audio, press the POWER button to OFF.
2. Toggle through the SNOOZE/NAP bar to the corresponding time of your
choice: 15, 30, 45 or 60 minutes – it will show on the LCD display.
3. Toggle through the AL MODE button until the corresponding wake mode icon
of your choice lights up on the LCD display: iPod/iPhone, Radio or Beep tone.
4. The alarm will sound to wake you up after the selected number of minutes
have passed.
5. To cancel the Nap timer, press the SNOOZE/NAP bar until OFF shows on the
LCD display, which indicates the Nap function is disarmed.

Dimmer Control:

Press the DIMMER button (located behind unit) to adjust the backlight intensity of
the LCD display.
9