Honeywell HD4D Quick Install Manual page 2

Retighten the locking screws.
Make Final Adjustments to Lens Focus
Lenses are pre-focused at the factory. In the unlikely event the optical effect of
the dome causes a slight defocusing of the lens, hold the dome over the lens
to make to make a final adjustment.
5
Operate Your Camera
OSD Menu Controls
Legend
#
2
1
2
1
OSD Menu Structure
SETUP MENU
Set Up Your Camera
SETUP Menu
Menu Item Option
LENS DC!
VIDEO
MANUAL
SHUTTER FLK
ESC!
MANUAL
WHITE BAL ATW
(White Balance) MANUAL!
AWC!
BACKLIGHT OFF
LOW
MIDDLE
HIGH
AGC OFF
LOW!
MIDDLE!
HIGH!
DNR (Digital OFF
Noise LOW
Reduction) MIDDLE
HIGH
SENS-UP OFF
(Sensitivity Up) AUTO
EXIT
© 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell
Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject
to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Description
Video-test monitor output connector
Camera OSD joystick control (four position plus center push)
Press this control To do this
UP, DOWN Select a new item
LEFT, RIGHT Select a menu item
SETUP (MENU) Enter SETUP MENU,
(CENTER PUSH) access a submenu
↵,
LENS DC VIDEO, MANUAL
↵,
SHUTTER
FLK, ESC MANUAL
↵,
WHITE BAL.
ATW, MANUAL AWC
BACKLIGHT OFF, LOW, MIDDLE, HIGH
↵,
AGC OFF, LOW, MIDDLE
DNR
OFF, LOW, MIDDLE, HIGH
!
SENS-UP
OFF, AUTO
SPECIAL
CAMERA ID
DAY/NIGHT
SYNC
MOTION DET
EXIT MENU
PRIVACY
MIRROR
SHARPNESS
RESET
Description
Lens type. Only DC mode is available at this time.
Caution Selecting VIDEO or MANUAL adversely
affects camera operation.
FLK (Flickerless) = reduce on-screen flickering.
MANUAL = adjust shutter speed from 1/60 - 1/
100,000 second (NTSC), or 1/50 - 1/120,000 (PAL).
MANUAL is not available in DC lens mode.
ESC = adjust on-screen brightness level. ESC is not
available in DC lens mode.
Control color on the screen.
ATW (Auto Tracing White Balance) = for color
temperature 2400°K - 12000°K (for example, under a
fluorescent light, or outdoors).
MANUAL = finely adjust the white balance. increase
or decrease the red or blue factor while monitoring
the difference on the screen.
AWC (Auto White Balance Control) = camera
automatically adjusts the white balance to your
environment.
Provide intelligent light level control to overcome
severe backlighting conditions.05/07
Increase the GAIN level to brighten the picture
(noise/distortion may develop).
Increase the DNR level to reduce noise/distortion on
screen. This may introduce video artifacts. DNR is
deactivated if AGC is turned off.
AUTO = Automatically provide a clear image under
low-light conditions. Adjust the maximum low-light
magnification from 2x to 128x. Increasing
magnification may cause noise/distortion.
Exit the SETUP menu and returns to video
monitoring.
,
↵
↵
HIGH
6
SPECIAL Menu
Menu Item Option Description
CAMERA ID OFF Display a name and/or number on the monitor. To
ON add a camera title:
UP, DOWN, LEFT, or RIGHT menu control = select a
CAMERA ID
character, then press (SETUP) MENU to accept it. The
character is saved and the title cursor at the bottom of
A B C D E F G H I J K L M
the screen moves to the next position.
N O P R Q S T U V W X Y Z
a b c d e f g h i j k l m
# $ = go back or forward in the title name to make
n o p q r s t u v w x y z
changes.
– . 0 1 2 3 4 5 6 7 8 9
CLR = delete the entire name and start again.
# $ CLR POS END
POS = position the camera title on the screen. Press
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
(SETUP) MENU to confirm the position.
END = accept the new name.
DAY/NIGHT AUTO AUTO = Automatically detect color or black/white
ON
ON = Full-time color mode.
SYNC INT INT = Synchronize the vertical interval sync pulse of
L/L your camera with other equipment to reduce the
effect of picture roll on the monitor.
L/L (Line Lock) = adjust the phase from 0° - 359°.
Menu Item
<SYNC. CONTROL>
INTERNAL
LINELOCK
SYNC INT (L/L)
RETURN!
RETURN
MOTION DET OFF Detect moving objects on screen; displays MOTION
ON! DETECTED along with the number of movements
counted. Select the area on screen you want to
observe.
Menu Item Option
MOTION DETECTION
AREA SEL
AREA SEL AREA 1
AREA STATE ON
TOP |..|................| 10
DOWN |........|..........| 25
LEFT |...|...............| 20
AREA
RIGHT |........|..........| 40
STATE
Press SET to Return
TOP
DOWN
LEFT
RIGHT
PRIVACY OFF Mask up to 4 areas of the screen from video
ON! monitoring.
Menu Item Option Description
PRIVACY
AREA SEL
AREA SEL AREA 1
AREA STATE ON
AREA TONE |...............|...| 80
TOP |..|................| 10
DOWN |........|..........| 25
AREA
LEFT |...|...............| 20
STATE
RIGHT |........|..........| 40
AREA
Press SET to Return
TONE
TOP
DOWN
LEFT
RIGHT
MIRROR OFF Produce a horizontal mirror image on screen.
ON
SHARPNESS ON! Sharpen the image on screen (image level 0 - 31).
OFF Excessive sharpening may cause picture noise.
RESET Restore all factory default settings.
RETURN! Return to the main SETUP menu.
Install the Enclosure Cover
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
Document 800-00027 – Rev B – 05/07
Description
When line lock is not required.
Adjust the vertical phase (VPH)
from 000 – 359 (factory default is
0). Line-lock is only available with
24 VAC power.
Press MENU to return to the SETUP
menu.
Description
AREA 1 Select a motion detection grid
AREA 2 (top left, top right, bottom left,
AREA 3 bottom right) to modify.
AREA 4
ON Activate or deactivate the
OFF selected grid.
Press LEFT or RIGHT menu
control left or right to alter the
dimensions of the selected
grid.
AREA 1 Select a masking grid (top left,
AREA 2 top right, bottom left, bottom
AREA 3 right) to modify.
AREA 4
ON Activate/deactivate the
OFF selected grid.
Press LEFT or RIGHT menu
control to change the shade of
the masking grids.
Press LEFT or RIGHT menu
control to alter the dimensions
of the selected grid.
HD4D dome enclosure
Use Allen key to secure dome
enclosure to base (#8-32
security screws (x4)