Dvdubbing - Toshiba DVR670KU Owner's Manual

"T1
l:
::;
,.,
,...
, o'
:::r
; V\
Ill:>
if!
j-o
f
i<
:1""\
':xl
, "T1
,I:
I::!
'n
...
10'
:::r
m
C.
;::;:
::;
~
is
01
J
III
0
,~
V;'
31"1
III
::;
,...
tl:l
~
~ ~.
;r'\
, VI
lro
! ...
!e:
,i:l
r------
i"tl
iij
; '<
:g"
'1"1
!~
6
DVC is in recording pause
mode.
EN 57
DVC is fast forwarding.
(in stop mode)
DVC is fast reversing.
(in stop mode)
DVC is fast reversing.
(standard speed)
DVC is fast reversing.
(faster than above)
DVC is fast reversing.
(faster than above)
DVC is in slow reverse
playback.
DVC is in recording.
When the DVe is not
in camera mode...
o
IT fC :
0
DVC is fast forwarding.
(standard speed)
DVC is fast forwarding.
(faster than above)
DVC is fast forwarding.
(faster than above)
DVC is slow forwarding.
(standard speed)
DVC is slow forwarding.
(faster than above)
DVC is slow forwarding.
(faster than above)
DVC is in pause mode.
The menu changes according to
what mode of
Dve
Switch the mode on the DVC to
playback mode for the dubbing
information.
DO
6. Product name of your DVC
• If the unit cannot recognize the
input signal from the DVC or the
unknown product, "No Device" or
"****"
will appear instead.
7. Status of the current operation
and the time counter
Each icon means (Available icons
may vary depending on the DVC):
o
DVC is in stop mode.
[>
DVC is in playback mode.
4
When the DVe is
i
in video mode...
[~n~ ~
2
The following instructions are described with the operations using the remote control of this unit.
DVDUBBING
1.DV icon
2. Indicator of active device
• When the "Control" is
highlighted, press [ENTER] to
display the item selection. Use
[. I
T]
to select the device you
wish to operate, then press
[ENTER] to activate.
• Select "DVD" to control this unit.
• Select "DVC to control your DVC.
3. Recording audio mode
• Other than the DVC is in stop
mode, the "DV Audio" can be
selected. Press [ENTER] to display
the item selection and then use
[. I
T] to select the audio you
wish to output. Press [ENTER]
again to activate.
• Select "Stereo 1" to dub the stereo
sound.
• Select "Stereo2" to dub the sound
with after recording sound.
• Select "Mix" to dub the stereol
and stereo2.
4. Indicator of dubbing function
• When the unit is ready for
dubbing, "Start Rec" will appear.
• When the unit is in dubbing,
"Pause Rec" will appear.
5. Channel position
• When you select "L3 (DV-IN)" by
using [INPUT SELECT -€>] or
[CH A
I
V], "L3 (DV-IN)" will
appear.
3
~
You cannot control the DVC in VCR mode. For dubbing onto VCR, refer to page 59.
This function helps you to easily dub the contents of the DVC (digital video camcorder) to this unit.
You can control basic operations of the DVC from the remote control of this unit such as playback, fast forward or
reverse and stop all operations if the DVC is in video mode. Use the DV cable that has 4-pin input jack and is
compliance with the IEEE1394 standards. When you connect to DV input jack on the front of this unit, select
"L3(DV-IN)" position by using [INPUT SELECT -€>] or [CH
A
I
V]
on the remote control and press [DISPLAY] to show
the DV dubbing information for the operation of your DVC.
...Guide to DV
_~Dd On-S~r.eeo
Dis