TABLE OF CONTENTS About This Guide ................. 1 Purpose ..................... 1 Introduction ..................2 Fast Ethernet Technology ..............2 Switching Technology ..............3 Power over Ethernet (PoE) .............. 4 Features .................... 4 Unpacking and Installation ..............5 Unpacking ..................5 Setup ....................
PD devices. The Switch will automatically detect the network appliance’s requirements, and will supply the required power to each appliance accordingly. Purpose This manual will familiarize you with the DES-1005P and guide you through the installation process.
INTRODUCTION Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks. A number of high-speed LAN technologies have been proposed to provide greater bandwidth and improve client/server response times. Among them, 100BASE-TX (Fast Ethernet) provides a non-disruptive, smooth evolution from the current 10BASE-T technology.
Switching Technology Switching is a cost-effective way of increasing the total network capacity available to users on a local area network. A switch increases capacity and decreases network loading by dividing a local area network into different segments, which don’t compete with each other for network transmission capacity.
Power over Ethernet (PoE) Power over Ethernet (PoE) integrates power and data onto one single cabling infrastructure, eliminating the need to have AC power available at all locations. Power and Data is integrated onto the same cable, supporting category 5/5e up to 100 Meters. PoE will provide power to PoE compatible devices, such as IP telephones, wireless LAN access points and IP security cameras.
If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the DES-1005P can be performed using the following steps: The power outlet should be within 1.82 meters (6 feet) of the Switch.
Connecting Network Cable The Switch support 5 10/100Mbps Ethernet ports and Port 1 PoE Enabled port, the PoE port will automatically activate when a compatible terminal is identified. The Switch will supply power through the Ethernet port to the connected PoE powered device (PD). For legacy devices that are not compatible, the PoE port will not offer power to this device.
The figure below shows the front panels of the DES-1005P. Figure 1. Front panel Power LED Indicator: This green indicator light is on when the DES-1005P is receiving power; otherwise, it is off. Ethernet Ports (Port 1~5): These ports support network speeds of either 10Mbps or 100Mbps, and can operate in half- and full- duplex transfer modes.
Rear Panel The figure below shows the front panels of the DES-1005P. Figure 2. Rear panel DC Power Jack: Connect to the power adapter Power Switch: Use to turn on/off the Switch...
UNDERSTANDING LED INDICATORS The front panel LEDs provides instant status feedback, and helps monitor and troubleshoot when needed. Figure 3. LED indicators of the Switch System LED LED Indicators Color Status Description Indicative Green Solid Light Power on Power (per device) Off Light Power off Link/Act...
Alternative A which is sending out power over number 1,2,3,6 pins of 8 wires of CAT5 UTP cable DES-1005P works with all D-Link 802.3af devices DES-1005P works with all non-802.3af capable D-Link AP, IP Cam and IP phone via DWL-P50...
MOUNTING THE SWITCH ON A WALL The DES-1005P can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: A.) Mounting on a cement wall...
TECHNICAL SPECIFICATIONS General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af Power over Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half duplex), 200Mbps (full-duplex) Topology Star Network Cables...
Page 16
Performance RAM Buffer: 64K bytes per device Filtering Address Table: 1K entries per device Packet Filtering/Forwarding Rate: 10Mbps Ethernet: 14,880/pps 100Mbps Fast Ethernet: 148,800/pps MAC Address Learning: Automatic update Transmits Method: Store-and-forward...