Panasonic Lumix DMC-FZ30PP Service Manual page 46

Service Manual
Diagrams and Replacement
Parts List
Digital Camera
DMC-FZ30PP DMC-FZ30GD
DMC-FZ30PL DMC-FZ30GK
DMC-FZ30EB DMC-FZ30GN
DMC-FZ30EG DMC-FZ30GT
DMC-FZ30EGM DMC-FZ30SG
DMC-FZ30GC
Vol. 1
Colour
(S)...........Silver Type
(K)...........Black Type
Table of contents
S1. ABOUT INDICATION OF THE SCHEMATIC DIAGRAMS ....... S-1
S1.1. IMPORTANT SAFETY NOTICE: ........................................... S-1
S2. BLOCK DIAGRAM ................................................................... S-2
S2.1. OVERALL BLOCK DIAGRAM ............................................... S-2
S2.2. SYSTEM CONTROL BLOCK DIAGRAM .............................. S-3
S2.3. VIDEO/AUDIO PROCESS BLOCK DIAGRAM ..................... S-4
S2.4. SENSOR BLOCK DIAGRAM ................................................ S-5
S2.5. LENS DRIVE BLOCK DIAGRAM .......................................... S-6
S2.6. POWER BLOCK DIAGRAM ................................................. S-7
S3. SCHEMATIC DIAGRAMS ........................................................ S-8
S3.1. INTERCONNECTION DIAGRAM ......................................... S-8
S3.2. FLASH SCHEMATIC DIAGRAMS ........................................ S-9
S3.3. LCD IF FLEX SCHEMATIC DIAGRAMS ............................. S-10
S3.4. AF ASSIST SCHEMATIC DIAGRAMS ................................ S-10
S3.5. CCD FLEX SCHEMATIC DIAGRAMS ................................ S-11
S3.6. MIC FLEX SCHEMATIC DIAGRAMS ................................. S-11
S3.7. LENS FLEX SCHEMATIC DIAGRAMS ............................... S-12
DSC0508016CE
S1. ABOUT INDICATION OF THE SCHEMATIC DIAGRAMS
S1.1. IMPORTANT SAFETY NOTICE:
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as "●" mark.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
S4. PRINT CIRCUIT BOARD ....................................................... S-13
S4.1. FLASH P.C.B. ...................................................................... S-13
S4.2. LCD IF P.C.B. ...................................................................... S-14
S4.3. AF ASSIST P.C.B. ............................................................... S-14
S4.4. CCD FLEX .......................................................................... S-15
S4.5. MIC FLEX ........................................................................... S-16
S4.6. LENS FLEX ......................................................................... S-16
S5. REPLACEMENT PARTS LIST ............................................... S-17
S6. EXPLODED VIEWS ............................................................... S-23
S6.1. FRAME & CASING SECTION (1) ....................................... S-23
S6.2. FRAME & CASING SECTION (2) ....................................... S-24
S6.3. FRAME & CASING SECTION (3) ....................................... S-25
S6.4. PACKING PARTS & ACCESSORIES SECTION ................ S-26
S-1 S-1
Circuit name being connected.
This signal is connected
OFTR FEP
to the EFP schematic diagram
Name of Signal
HAVE THE SPECIAL CHARACTERISTICS