SDM-S71 US Model SERVICE MANUAL Canadian Model AEP Model Southern Hemisphere Model SPECIFICATIONS Dimensions (width/height/depth) LCD panel Panel type: a-Si TFT Active Matrix Display (upright): Picture size: 17.0 inch Approx. 423 233 mm Input signal format RGB operating frequency* ´...
Page 2
8. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described right. 0.15 µF 1.5 kΩ Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SDM-S71(E) 2...
Page 3
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE DEMAGNETISATION EST ENLEVÉE. PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART ATTENTION AUX COMPOSANTS RELATIFS À LA SÉCURITÉ!! NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET UNE...
** “ deep sleep ” is the power saving mode defined by the Environmental Protection Agency. *** If only the horizontal or vertical sync signal is input to the monitor, the power indicator may alternately flash green and orange. SDM-S71(E) 4...
Other functions are used for design engineering. There is no guarantee of using these N/A functions. 3. W/B readjustment is required after the panel, board, and microcomputer are replaced. However, be sure to perform aging for more than 30 minutes for RGB reset before W/B adjustment. SDM-S71(E) 2-1...
1. Prepare timing and pattern data for a signal generator mode. 5. Repeat steps 1 to 4 to make the picture performance according to the Sony timing specifications. c. Confirm that the "backlight" register data is 0 optimum. 2. Connect a monitor video cable to the signal generator.
6. Adjust White Balance (9300K, 6500K & 5000K) and Luminance 9300K 6500K 5000K Tolerance (10 nits @ SONY CS-1000) by Sub-BRT 0.2838 0.3132 0.3450 }0.003 Remark: In normally, adjust G for Luminance (Y), adjust R for x and adjust B for y.
Collector Base ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. – a b 1 Discrete semiconductot Ver.1.6 Ref. No. (Chip semiconductors that are not actually used are included.) Circuit diagram division code SDM-S71 (E)
Page 21
(1) Schematic Diagram of H (KEY) Board INTERFACE (f) BOARD CN008 S001 S002 S003 S004 S005 S006 S007 POWER MENU CONTRAST BRIGHTNESS DOWN H BOARD (KEY ) B-SS3628<J..> - H.. SDM-S71 (E)
Page 23
One sheet of INTERFACE board circuit diagram is divided into six sheets, each having the code INTERFACE-a to INTERFACE-f. For example, the destination ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-S71 (E)
Page 24
One sheet of INTERFACE board circuit diagram is divided into six sheets, each having the code INTERFACE-a to INTERFACE-f. For example, the destination ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-S71 (E)
Page 25
One sheet of INTERFACE board circuit diagram is divided into six sheets, each having the code INTERFACE-a to INTERFACE-f. For example, the destination ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-S71 (E)
Page 26
One sheet of INTERFACE board circuit diagram is divided into six sheets, each having the code INTERFACE-a to INTERFACE-f. For example, the destination ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-S71 (E)
Page 27
One sheet of INTERFACE board circuit diagram is divided into six sheets, each having the code INTERFACE-a to INTERFACE-f. For example, the destination ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-S71 (E) 3-10...
Page 28
One sheet of INTERFACE board circuit diagram is divided into six sheets, each having the code INTERFACE-a to INTERFACE-f. For example, the destination ab1 on the code INTERFACE-a sheet is connected to ab1 on the INTERFACE-b sheet. a b 1 Ref. No. Circuit diagram division code SDM-S71 (E) 3-11...
The components identified ! marked are critical for safety. Replace only with the part number specified. Les composants identifiés par la marque sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. SDM-S71(E) 4-1...
X-ray radiation.Should replacement be required, replace only with the value originally used. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. SDM-S71(E) 5-1...
Page 34
*:INVERTER BOARD **:I/F MOUNT Board Type ! / * Ref.No. Part No. Descrption Remarks-1 Remarks-2 Difference FUSE F001 1-576-629-11 IC021 6-802-032-01 W7862B SDM-S71(E) 5-2...
Page 35
English Sony EMCS Corporation Ichinomiya TEC 2002EL08-Data Customer Service Section No.2 Made in Japan 2002. 5 9-978-729-01 Quality Assurance Dept. SDM-S71(E) XX...