SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service prevent potential shock reasons prior to applying power to the manual and its supplements and addenda, read and follow the unit under test. SAFETY PRECAUTIONS on page 3 of this publication. 2.
Page 5
IC Remove/Replacement 3. Solder the connections. Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced which the IC leads are inserted and then bent flat against the component and adjacent components and the circuit board to prevent excessive component temperatures.
Page 6
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range This specification is applied to ML-041G chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ±...
ADJUSTMENT INSTRUCTION 1. Application Object Item Unit Remark This document is applied to 23" Wide LCD TV which is White Balance, 0.272 0.287 0.302 MB/TB ±0.015(95% white manufactured in Monitor Factory or is produced on the basis X axis Video or comp1 mode) of this data.
SVC REMOCON FUNTION REAMARK To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function.
TROUBLESHOOTING No power :[A]Process (LED indicator off) Check short of main B/D Check 15V or 5V or Change Lips Fail of Lips Pass Pass Check Output of Change IC604, IC607 IC604, IC607 Fail Pass Change LED Assy Check LED Assy Fail Pass Check P701 Connector...
Page 14
No Raster :[B]Process Check LED Status Repeat A PROCESS on display unit Fail Check Change L300, L301, L302 L300, L301, L302 Fail Pass Check the input/ Change IC300 Output of IC300 Fail Pass Check inverter Change inverter Connector or inverter connector or inverter Fail Pass...
Page 15
No Raster on Component signal Repeat [A] Process Pass Check the signal of Check JA700 or R708, 709, 710 Check the input source. Fail Pass Re-soldering or Check the input/output Change the defect part Fail of IC200 Re-soldering or Check the input/ Change the defect part, output of IC100 Fail...
Page 16
No Raster on AV Signal No Raster on TV(RF) signal (Video, Side AV, S-Video) Check 5V, 33V of TU1000 Repeat Check the output of Re-soldering or [A] Process TU1000 Fail Fail Change the defect part Pass Change Check the signal of L103, L710, L713, L714 L103, L710, L713, L714 or Check input source...
Page 17
No Sound Check the Change source input input source Fail Pass Check the input/output Re-soldering of IC801 Fail Pass Re-soldering or Check the input/output Change the defect part of IC100 Fail Check X100 Pass Re-soldering or Check the input/output Change the defect part of IC400 Fail Pass...
Page 19
BLOCK DIAGRAM DESCRIPTION 1. Video Controller Unit & Display Data Conversion Unit The video controller unit receives the video signals inputted through the tuner, AV port (AV1, AV2, S-VIDEO, COMPONENT), and converts them into an analog RGB signal through the microcomputer (VCTI) combined with the video decoder that integrates various functions in one chip.
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)