Chamberlain Security Plus 96LMC Owner's Manual

Model 96LMC Security Plus
3-Channel Remote Control
OWNER'S MANUAL
The 90 Series remote control (with yellow battery test
light) works only with door openers and light controls
having an orange "Smart" button and a yellow indicator
light.
Programming instructions are described and illustrated
below. The additional push buttons can also activate
other garage door openers and/or light controls.
(Instructions for programming light products are
included with those accessories.)
Security Plus ™
To Program the Opener to Accept
the Remote Control Code
Select a remote control push button to operate the opener.
The large button is recommended for use with a garage
door opener.
1. Press and hold the selected remote control push button.
See Figure 1.
2. Press and release the "Smart" button on the opener
panel. See Figure 2. The indicator light on the panel will
begin to blink and the opener lights will flash once.
3. Release the remote push button.
Now the opener will operate when that remote control
button is pressed. Test it by pressing the remote button to
see that the door goes up and down.
Adding a remote can also be done from the door control, as
follows:
1. With the door closed, press and hold a remote push
button.
2. Press and hold the Light button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button.
To Erase All Remote Control Codes
Press and hold the "Smart" button on the opener panel until
the indicator light turns off (about 6 seconds). All transmitter
codes are now erased. Then follow the steps above to
re-program each remote control.
Replacement Parts
Model 96LM Security Plus remote case, cover, screw
(circuit board not included)
12 Volt battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10A14
114A2088
™
Garage Door Openers
. . . . . . .41A5018
FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-654-4736
© 1996, The Chamberlain Group Inc.
Children operating or playing with a garage door opener
can injure themselves or others. The garage door could
close and cause serious injury or death. Do not allow
children to operate the wall push buttons or remote
controls.
A moving garage door could injure or kill someone under
it. Activate the opener only when you can see the door
clearly, it is free of obstructions, and is properly adjusted.
NOTICE: To comply with FCC/IC rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Model 96LMC
Security Plus™
Remote Control
Yellow
Battery Indicator
Light
push button
Figure 1
With Security Plus transmitters, a remote push button can
be programmed to operate the opener lights without
opening the door.
1. With the door closed, press and hold the remote button
that you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
Your Security Plus remote control can be programmed to
operate one door using all 3 buttons: the large button will
only open the door, the middle button will only close the
door, and the third button will stop the door's movement.
You may set up this feature as follows:
1. With the door closed, press and hold
the large remote push button.
2. Press and hold the Lock button on
the door control.
3. Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test by
pressing the large (Open) button on the remote. The door
should open. Press it again while the door is open and
nothing should happen. Press the middle (Close) button
and the door should close. Press the third (Stop) button
while the door is moving and it should stop immediately.
All Rights Reserved
WARNING
Garage Door Opener
with "Smart" Button
"Smart"
Select a Button Indicator Light
Figure 2
To Control the Opener Lights
Open/Close/Stop Operation
1 2 3
9 9
1 1
7 3 7 3
5 5
KG
KG
Open
Close
Stop
Printed in Mexico