General Specifications; Input/Output Specifications - Yamaha QL Series Brochure & Specs

General Specifications

Internal
Sampling Frequency
External
Signal Delays Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz
100mm motorized, Resolution=1024steps
Fader
+10dB to –138dB, –∞dB all faders
+0.5, –1.5dB 20Hz-20kHz,
Frequency Response
refer to +4dBu output @1kHz INPUT to OMNI OUT
Total Harmonic Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω
Distortion INPUT to OMNI OUT, Input Gain= Min.
*3
–128dBu typ., Equivalent Input Noise, Input Gain= Max.,
Hum & Noise
*4
–88dBu, Residual output noise, ST master off
112dB typ., DA Converter,
Dynamic Range
108dB typ., INPUT to OMNI OUT, Input Gain= Min.
Crosstalk@1kHz –100dB *1
Dimensions (WxHxD) QL5: 828mm x 272mm x 563mm (32.6in x 10.7in x 22.2in), 21.8kg (48.1lb)
and Net Weight QL1: 468mm x 272mm x 562mm (18.4in x 10.7in x 22.1in), 14.7kg (32.4lb)
Power Requirements QL5: 200W
(in watts) QL1: 135W
Power Requirements
100-240V 50/60Hz
(in volts,Hz)
Temperature Range Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃
Included Accessories Owner's Manual, dust cover (QL5 only), power cord, DVS license sheet
Rackmount kit RK1 (QL1 only), Mini-YGDAI cards
Optional Accessories
Gooseneck Lamp LA1L, Nuendo Live
*1. A 22kHz, 30dB/Oct filter is used to measure crosstalk.
*2. For more information about Mini-YGDAI card support, refer to the Yamaha pro audio website.
http://www.yamahaproaudio.com/
*3. An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
*4. An A-Weight filter is used to measure hum & noise.

Input/Output Specifications

Analog input specifications
Input Input
GAIN
Connectors Impedance
+66dB
INPUT
7.5 kΩ
1-32 *6
–6dB
*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu= 0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the
console software.
*6. QL1: INPUT1-16
21
44.1kHz
48kHz
44.1kHz
+4.1667%, +0.1%, –0.1%, –4.0%
48kHz
+4.1667%, +0.1%, –0.1%, –4.0%
, adjacent INPUT/OMNI OUT channels, Input Gain= Min.
,
*2
Input Level
Source
Impedance
Sensitivity Nominal Max. before clip
*1
–82dBu –62dBu –42dBu
50-600 Ω
(61.6μV) (0.616mV) (6.16mV)
Mics &
–10dBu +10dBu +30dBu
600 ΩLines
(245mV) (2.45V) (24.5V)
Analog output specifications
Output
Connectors
±200ppm
±200ppm
OMNI
OUT 1-16 *7
PHONES
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu= 0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8
Digital input/output specifications
Connectors
Primary/Sec-
ondary
*1. QL1: 32ch Input/32ch Output@48kHz
Digital output specifications
Connectors
DIGITAL OUT AES/EBU AES/EBU Professional Use
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
I/O SLOT (1-2) specifications
Each I/O Slot accepts a Mini-YGDAI card.
Only Slot 1 has a serial interface.
Control I/O specifications
Connectors
MIDI
Connector
WORDCLOCK
GPI (5IN/5OUT)
XLR-3-31
NETWORK
type
LAMP (QL5: x 2, QL1: x 1)
(Balanced) *2
USB HOST
*1. Input pin: TTL level, w/ internal pull-up (47kΩ) Output pin: Open drain output (Vmax=12V, maximum sink current/pin=-
75mA) Power supply pin: Output voltage Vp=5V, Max. output current=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp nominal power: 5W, Brightness (voltage) can be adjusted from the software.
Maximum
Output Load
Output
Defined
Impedance Impedance
Level
*5
Level
+24dB +4dBu
(default) (1.23V)
600 Ω
75 Ω
Lines
–2dBu
+18dB
(616mV)
8 Ω
– 75mW
Phones
15 Ω
40 Ω
– 65mW
Phones
Format Data length Level
Dante 24bit or 32bit 1000Base-T
Format Data length Level
24bit
Format Level
IN MIDI –
OUT MIDI –
IN – TTL/75 Ω terminated
OUT – TTL/75 Ω
– –
IEEE802.3 10BASE-T/100Base-TX
– 0V-12V
USB 2.0 –
Output Level
Connector
Maximum
Non-Clip Level
vt+24dBu
(12.3V)
XLR-3-32 type
(Balanced) *1
+18dBu
(6.16V)
150mW
*6
Stereo Phone
Jack(TRS)
(Unbalanced)
*2
150mW
*6
Audio Connector
64ch Input/64ch
EtherCON Cat5e
Output@48kHz *1
Connector
RS422 XLR-3-32 type (Balanced)
*1
Connector
DIN Connector 5P
DIN Connector 5P
BNC Connector
BNC Connector
D Sub Connector 15P(Female)
*1
RJ-45
XLR-4-31 type
*2
USB A Connector (Female)