Whirlpool ADP 5600 Quick Reference Manual

Quick reference guide
PROGRAM SELECTION START/RESUME BUTTON
BUTTON Push this button to start the selected program: the
Push "Programs" button indicator lights up and goes off at the end of the
(repeatedly) until the indicator program. When the door is opened during a
of the required program lights washing cycle, the cycle is temporarely paused: the
up (see "Table of programs" Start indicator blinking. To restart the cycle close
below). the door and push Start button again.
Table of programs
P
Programs
1
Pre-Wash cold
2
Glasses 40°C
3
Quickwash 40°C
4 2)
50°C
Eco
5
Intensive 70°C
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance's automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
"nk_customer@whirlpool.com".
(see at right for options description)
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter "What to do if ...".
Available
Loading instructions
options
Delay Crockery to be washed later.
Light soiling, for example glasses
Delay
and cups.
Lightly soiled crockery, with no
Delay
dried-on food.
Delay
Normally soiled crockery.
Half load
Recommended program for
Delay heavily soiled crockery, especially
suitable for pans and saucepans.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
AUTOMATICALLY AFTER 30 SECONDS IF ANY CYCLE IS STARTED.
Options and display description
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir
needs to be refilled.
HALF LOAD BUTTON
Half load cycle can be used
for the upper or lower rack.
Consumption
Select the required program
Deter-
then press the "Half Load"
gent
1)
Litres kWh Minutes
button - the light comes on.
Turns off at the end of the
program. The "Half Load"
— 5.0 0.02 10
option can be used with the
programs indicated in the
table of programs.
X 13.0 0.90 97
X 13.0 0.70 30
TABLET SETTING
X 15.0 1.05 150 This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator
lights up) if you are using the combined detergents in
X 15.0 1.50 140
tablet (rinse aid, salt and deteregent in 1 dose).
If you are using powder detergent or liquid detergent,
the Tablet indicator on the control panel has to be off.
ADP 5600
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
5019 396 01838/B
Chart
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid
dispenser needs to be
refilled.
DELAYED START
BUTTON
The wash cycle can be
programmed to start
after 2, 4 or 8 hours.
Then press the Start
button. The wash
program will start after
the set time.
GB -1-