Table of Contents
Advertisement
Quick Links
Quick reference guide
PROGRAM SELECTION
START/RESUME BUTTON
BUTTON
Push this button to start the selected program: the
Push "Programs" button
indicator lights up and goes off at the end of the
(repeatedly) until the indicator
program. When the door is opened during a
of the required program lights
washing cycle, the cycle is temporarily paused: the
up (see "Table of programs"
Start indicator blinks.
below).
To resume the cycle push the Start button and
close the door within 3 seconds.
Table of programs
P
Programs
1
Pre-Wash
cold
2
Quickwash
40°C
3
2)
50°C
Eco
4
3)
Antibacterial
5
Intensive
70°C
1)
Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options)
and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance's
automatic calibration system.
2)
Reference program for energy label in compliance with EN 50242 regulations. - Note for T esting Institutes: for detailed information on the EN/
Standard loading comparison test and other tests, contact the following address: "nk_customer@whirlpool.com".
3)
The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November
2001.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher
(1 minute process).
If the indicator flashes repeatedly, see page 6 -
chapter "What to do if ...".
Loading instructions
Crockery to be washed later.
Lightly soiled crockery, with no dried-on
food.
Normally soiled crockery.
Energy-saving program.
Normally or heavily soiled crockery, with
additional antibacterial wash. Program
interruption (e.g. due to door opening) can
compromise elimination of germs.
Recommended program for heavily soiled
crockery, especially suitable for pans and
saucepans.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
Consumption
Deter-
gent
1)
Litres
kWh
Minutes
—
5.0
0.02
10
X
13.0
0.70
30
X
15.0
1.05
165
X
16.0
1.75
120
X
15.0
1.50
140
ADG 6600
QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Chart
5019 300 00256
EN -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADG 6600
Summary of Contents for Whirlpool ADG 6600
- Page 1 Reference program for energy label in compliance with EN 50242 regulations. - Note for T esting Institutes: for detailed information on the EN/ Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”. ADG 6600...
- Page 2 First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only - Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. before the first wash or if water - Programs LEDs will indicate the water hardness setting.
- Page 3 Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Visual The rinse aid dosage can be indicator adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).
- Page 4 How to load the racks How to load UPPER RACK How to adjust upper rack height (if available). (depending on the model) B - Cutlery basket - half: can be placed in the upper rack A - Adjustable flaps: in horizontal position for cups/ It could be useful to lift up the upper rack to have when the “Half load/Multizone”...
- Page 5 Select program Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc.
- Page 6 What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance...
- Page 7 What to do if... Crockery and cutlery... Possible causes... Solutions..salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up..have deposits: regeneration salt residue - Water too hard.
- Page 8 What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:...