Advertisement
The basic installation of this Smoke Alarm is similar whether you want to
install one Smoke Alarm, or interconnect more than one Smoke Alarm. If
you are interconnecting more than one Smoke Alarm, you MUST read
"Special Requirements For Interconnected Smoke Alarms" below before
you begin installation.
ELECTRICAL SHOCK HAZARD. Turn off power to the area where you
will install this unit at the circuit breaker or fuse box before beginning
installation. Failure to turn off the power before installation may result
in serious electrical shock, injury or death.
1. Remove the mounting bracket from the base, and attach it to the
junction box.
Model 7010B Only: Activate the battery back-up by removing the "Pull
to Activate Battery Back-Up" tab. Or, install battery back-up. Battery
back-up cannot work until you install the battery in the correct position
(Match "+" to "+" and "-" to "-").
Push and hold test button until the alarm sounds:
3 beeps, pause, 3 beeps, pause.
2. Using wire nuts, connect the power connector to the household wiring.
STAND-ALONE ALARM ONLY:
•
Connect the white wire on the power connector to the neutral wire in
the junction box.
•
Connect the black wire on the power connector to the hot wire in the
junction box.
•
Tuck the orange wire inside the junction box. It is used for interconnect
only.
INTERCONNECTED UNITS ONLY:
Strip off about 1/2" (12 mm) of the plastic coating on the orange wire
on the power connector.
•
Connect the white wire on the power connector to the neutral wire in
the junction box.
•
Connect the black wire on the power connector to the hot wire in the
junction box.
•
Connect the orange wire on the power connector to the interconnect
wire in the junction box. Repeat for each unit you are interconnecting.
Never connect the hot or neutral wires in the junction box to the orange
interconnect wire. Never cross hot and neutral wires between Alarms.
3. Plug the power connector into the back of the Smoke Alarm.
4. Position the base of the Smoke Alarm over the mounting bracket and turn.
The Alarm can be positioned over the bracket every 90°. Turn the Smoke
Alarm clockwise (right) until the unit is in place.
5. Check all connections.
Improper wiring of the power connector or the wiring leading to the
power connector will cause damage to the Alarm and may lead to a
non-functioning Alarm.
STAND-ALONE ALARM ONLY:
•
If you are only installing one Smoke Alarm, restore power to the
junction box.
INTERCONNECTED UNITS ONLY:
•
If you are interconnecting multiple Smoke Alarms, repeat steps
1-5 for each Smoke Alarm in the series. When you are finished,
restore power to the junction box.
ELECTRICAL SHOCK HAZARD. Do not restore power until all Smoke
Alarms are completely installed. Restoring power before installation is
complete may result in serious electrical shock, injury or death.
6. Make sure the Smoke Alarm is receiving AC power. Under normal
operation, the Green power indicator light will shine continuously.
7. If the Green power indicator light does not light, TURN OFF POWER
TO THE JUNCTION BOX and recheck all connections. If all connections
are correct and the Green power indicator still does not light when you
restore the power, the unit should be replaced immediately.
8. Test each Smoke Alarm. Press and hold the Test/Silence button until the
unit alarms. When testing a series of interconnected units you must
test each unit individually. Make sure all units alarm when each one
is tested.
If any unit in the series does not alarm, TURN OFF POWER and recheck
connections. If it does not alarm when you restore power, replace it
immediately.
FOLLOW THESE INSTALLATION STEPS
Special Requirements For Interconnected Smoke Alarms
Interconnected units can provide earlier warning of fire than stand-alone units,
especially if a fire starts in a remote area of the dwelling. If any unit in the series
senses smoke, all units will alarm. To determine which Smoke Alarm initiated an
alarm, see table:
On Initiating Alarms
On All Other Alarms
Interconnect units within a single family residence only. Otherwise all
households will experience unwanted alarms when you test any unit in the
series. Interconnected units will only work if they are wired to compatible units
and all requirements are met. This unit is designed to be compatible with:
First Alert
Electronics
5919; BRK Electronics
Smoke/CO Alarm Model SC6120B; Relay Module RM3.
Interconnected units must meet ALL of the following requirements:
3
• Failure to meet any of the above requirements could damage the
units and cause them to malfunction, removing your protection.
• AC and AC/DC Smoke Alarms can be interconnected. Under AC
power, all units will alarm when one senses smoke. When power is
interrupted, only the AC/DC units in the series will continue to send
and receive signals. AC powered Smoke Alarms will not operate.
Red LED flashes rapidly
Red LED is Off
®
Smoke Alarm Models SA4120, SA4121B, SA100B and BRK
®
Smoke Alarm Models 100S, 2002RAC, 4120, 4120B, 4120SB,
®
Heat Alarm Models HD6135F, HD6135FB;
• A maximum of 18 compatible units may be interconnected
(Maximum of 12 Smoke Alarms).
• The same fuse or circuit breaker must power all interconnected units.
• The total length of wire interconnecting the units should be less than
1000 feet (300 meters). This type of wire is commonly available at
Hardware and Electrical Supply stores.
• All wiring must conform to all local electrical codes and NFPA 70 (NEC).
Refer to NFPA 72, NFPA 101, and/or your local building code for further
connection requirements.
}
A. Unswitched 120VAC
B. To additional units; Maximum = 18 total
60 Hz source
(Maximum 12 Smoke Alarms)
1. Smoke Alarm
4. Wire Nut
2. Ceiling or Wall
5. Junction Box
3. Power Connector
6. Neutral Wire (Wht)
}
7. Interconnect Wire
(Orange)
8. Hot Wire (Blk)
Hide quick links:
Advertisement
