How To Use Your Tractor - Poulan Pro PD185H42STC Owner's Manual

For Parts Call K&T 606-678-9623 or 606-561-4983
The operation of any tractor can result in foreign objects thrown into the eyes, which
can result in severe eye dam age. Always wear safety glass es or eye shields while op-
erating your tractor or per form ing any adjustments or repairs. We rec om mend a wide
vision safety mask over spectacles or stan dard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 7)
Your tractor is equipped with an operator presence sens-
ing switch. When engine is running, any attempt by the
op er a tor to leave the seat without fi rst setting the parking
brake will shut off the engine.
• Depress clutch/brake pedal into full "BRAKE" position
and hold.
• Place parking brake lever in "ENGAGED" position and
re lease pressure from clutch/brake pedal. Pedal should
re main in "BRAKE" position. Make sure parking brake
will hold tractor secure.
ATTACHMENT CLUTCH LEVER
"ENGAGED" POSITION
THROTTLE/CHOKE
CONTROL
"BRAKE"
POSITION
CLUTCH/BRAKE
PEDAL "DRIVE"
POSITION
PARKING BRAKE
"DISENGAGED" PO SI TION
FIG. 7
STOPPING (See Fig. 7)
MOWER BLADES -
• To stop mower blades,move attachment clutch lever
to "DIS EN GAGED" po si tion.
GROUND DRIVE -
• To stop ground drive, depress clutch/brake pedal into
full "BRAKE" position.
• Move motion control lever to neutral (N) position.
IMPORTANT: THE MOTION CONTROL LEVER DOES NOT
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/
BRAKE PEDAL IS DEPRESSED.
ENGINE -
• Move throttle control to slow po si tion.
NOTE: Failure to move throttle control to slow position and
allowing engine to idle before stopping may cause engine
to "back fi re".
• Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
un author ized use.
• Never use choke to stop engine.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY
TO BE DIS CHARGED, (DEAD).
OPERATION
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot en gine exhaust gases may
cause "browning" of grass. To eliminate this possibility, al-
ways stop engine when stopping tractor on grass areas.
TO USE THROTTLE CONTROL (See Fig. 7)
Always operate engine at full throttle.
•
•
IGNITION
TO MOVE FORWARD AND BACKWARD (See
KEY
Fig. 7)
"DIS EN GAGED"
POSITION
The direction and speed of movement is controlled by the
PARKING BRAKE motion control lever.
"ENGAGED"
•
POSITION
•
•
MOTION
TO ADJUST MOWER CUTTING HEIGHT (See
CONTROL
LEVER
Fig. 7)
The position of the attachment lift lever determines the
cutting height.
•
•
The cutting height range is approximately 1-1/2 to 4".
The heights are measured from the ground to the blade tip
with the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
•
•
TO ADJUST GAUGE WHEELS (See Fig. 8)
Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position. Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.
NOTE:Adjust gauge wheels with tractor on a fl at level
surface.
11
www.mymowerparts.com
CAUTION: Always stop tractor com-
plete ly, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
Operating engine at less than full throttle reduces the
battery charging rate.
Full throttle of fers the best bagging and mower per for -
mance.
Start tractor with motion control lever in neutral (N)
position.
Release parking brake.
Slowly move motion control lever to desired position.
Grasp lift lever.
Press plunger with thumb and move lever to desired
position.
The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the fi rst cut
relatively high; the second to desired height.