Kenwood SD100 series Instructions

1
before using your Kenwood important (UK) only
appliance The wires in the cord are coloured
Read these instructions carefully as follows:
and retain for future reference. Green and Yellow = Earth
Remove all packaging and any Blue = Neutral
labels. Brown = Live.
The appliance must be protected
safety
by a 3A approved (BS1362) fuse.
WARNING: THIS APPLIANCE
general
Never touch the mixing shaft whilst MUST BE EARTHED.
the appliance is plugged in.
Note:
Keep fingers, hair, clothing and
For non-rewireable plugs the fuse
utensils away from moving parts.
cover MUST be refitted when
Always unplug:
replacing the fuse. If the fuse cover
before fitting or removing parts
is lost then the plug must not be
after use.
used until a replacement can be
before cleaning
obtained. The correct fuse cover is
Never mix hot ingredients.
identified by colour and a
Never use a damaged appliance.
replacement may be obtained from
Get it checked or repaired: see
your Kenwood Authorised Repairer
'service'.
(see Service).
Never put the appliance in water or
If a non-rewireable plug is cut off it
let the cord or plug get wet - you
must be DESTROYED
could get an electric shock.
IMMEDIATELY. An electric shock
Never let the cord touch hot
hazard may arise if an unwanted
surfaces or hang down where a
non-rewireable pug is inadvertently
child could grab it.
inserted into a 13A socket outlet.
Never add ingredients to the beaker
This machine complies with
whilst the appliance is operating.
European Economic Community
Only use the appliance with the
Directive 89/336/EEC.
beaker supplied.
before using for the first time
Make sure the beaker is located
1 Wash the parts: see 'cleaning'.
correctly before switching on the
appliance.
key
Do not let infirm people use the
appliance without supervision.
control switch
Do not let children use or play with
beaker support/interlock
the appliance.
mixing shaft
Only use the appliance for its intended
beaker rest
domestic use. Kenwood will not
beaker
accept any liability if the appliance is
maximum level
subject to improper use, or failure to
minimum level
comply with these instructions.
tilting head
before plugging in
Make sure your electricity supply is
the same as the one shown on the
power handle.
to use your drinks For best results, all liquid
ingredients should be as cold as
maker
possible. Milk drinks will taste better
if the milk is ice cold. The colder the
1 Make sure the control switch is off
milk, the thicker and more frothy the
(O) and then plug into the power
drink. Skimmed milk will produce a
supply.
frothier drink than semi-skimmed or
2 Place the ingredients into the
full fat milk.
beaker.
Never try to mix frozen fruit with
The beaker must always be filled to
your drinks mixer.
at least the minimum level mark
The drinks mixer will not crush ice.
or the liquid will not reach the
For best results, use ready crushed
mixing shaft. Do not fill above the
ice.
maximum level mark or liquid may
When blending large lumps of ice
overflow while mixing.
cream, break them up first.
3 Place the beaker onto the drinks
maker, making certain that the
cleaning
beaker's top edge is behind the
beaker support/interlock and its
Always switch off and unplug before
bottom edge is on the beaker rest.
cleaning.
Failure to locate the beaker into the
Never put the appliance in water or
beaker support/interlock will prevent
let the cord or plug get wet.
the appliance from operating.
beaker
To assist with the fitting or removal
Wash up, then dry. Or wash in your
of the beaker the drinks maker
dishwasher.
head can be tilted upwards .
mixing shaft
Never tilt the head during the
1 Place 200ml warm, lightly soapy
mixing operation.
water into the beaker. Attach the
4 Move the control switch to the
beaker to the drinks maker and
desired speed. Start mixing on
operate on speed 1 for 20 - 30
speed 1 then increase to speed 2 if
seconds. When finished, switch off
required.
and discard the liquid.
Most drinks should be mixed in less
2 Repeat the above step using clean
than 2 minutes.
warm water to rinse the mixer shaft.
5 When mixing is complete, switch off
3 Switch off and unplug the unit.
the drinks maker, remove the
Wipe any residual soap and water
beaker and pour out the drink.
from the mixer shaft with a damp
hints on using your drinks
cloth or sponge, then dry.
maker
To clean the exterior of the drinks
Always place the liquid ingredients
maker, wipe with a damp cloth or
into the beaker first.
sponge. Dry thoroughly.
Always mash fruit to a smooth
puree before adding to the beaker.
If using syrups and powdered mixes
add them just before mixing to
prevent them from sinking to the
bottom of the beaker.