Yaesu Mark-V FT-1000MP Operating Manual page 29

If the [ ENT ] key is pressed first, the yellow labels
on the keys become effective, for manually entering
any frequency one digit at a time; press [ SUB ( CE )]
then [ ENT ] to enter Sub-VFO frequencies directly.
35.SUB VFO-B [ RX & TX Switch-LED ]
These lamps select and indicate the current status
of Sub VFO-B. When the green "RX" lamp is lit, the
receiving frequency is under control of SUB VFO-B.
When the red "TX" lamp is lit, the transmitting frequency
is under control of SUB VFO-B. During dual receive
operation, the green "RX" lamps above both tuning
knobs Main and Sub) will be illuminated.
36.SUB VFO-B Tuning Knob
This knob adjusts the Sub VFO-B operating fre-
quency. The available tuning increments are the same
as described for the main tuning knob, although each
tuning knob's increments may be set independently
(see page 38).
37. [ LOCK ] Button
This button toggles locking of SUB VFO-B tuning
to prevent accidental frequency changes. The red in-
dicator in the display glows when this command is ac-
tive (the tuning knob can still be turned, but it does
nothing). Press the [ LOCK ] button again to re-enable
the tuning knob.
38.SUB SQL Knob
This separate control sets the signal level thresh-
old at which SUB VFO-B receiver audio is muted (and
the green "SUB BUSY" display indicator turns off), in
all modes. This control is normally kept fully CCW,
except when scanning and during FM operation.
39.CW and Electronic Keyer Controls
[ SPOT ] button turns the CW receiver spotting het-
erodyne oscillator on and off.
[ BK-IN ] button turns full break-in (QSK) CW opera-
tion on and off.
[ KEYER ] button toggles the internal CW keyer on/
off, as indicated by the LED above this button.
[ SPEED ] knob adjusts the keying speed of the keyer.
40.PITCH Knob
Rotate this control to select your desired CW tone
pitch (from 300~1050 Hz, in 50 Hz increments), as
shown in the display. The Tx sidetone, receiver IF pass-
band, and display offset from the BFO (carrier) fre-
quency are all affected simultaneously.
MARK-V FT-1000MP Operating Manual
F P
RONT
41. [ CLAR ] Buttons
Pressing the [ RX ] button activates the CLAR knob,
to allow offsetting the receiving frequency temporarily
(see item 42 below). The [ TX ] button provides the same
function for the transmit frequency. If both buttons are
pressed, the receiver and transmitter are both offset
from the original frequency. Pressing the [ CLEAR ] but-
ton zeroes any offset tuned by the CLAR knob. Each
memory and VFO retains all Clarifier settings indepen-
dently.
42. CLAR Knob
This knob tunes the Clarifier offset frequency up to
9.99 kHz when activated by the CLAR [ RX ] [ TX ] but-
tons just below it (a 3-digit display appears in the cen-
ter of the display (if enabled) when the Clarifier is ac-
tive).
43. NOTCH Knob
This knob adjusts the IF notch frequency when this
feature is activated by the [ NOTCH ] button located
above this knob. When activated, the LED inside the
[ NOTCH ] button glows red.
44. IDBT Indicator
This red indicator lights up when the IDBT System
is activated by pressing the [ IDBT ] button on the Shuttle
Jog. When this indicator is illuminated, the EDSP (Con-
tour) filter's bandwidth and center frequency changes
according to the SHIFT and WIDTH knob settings.
45. SHIFT Knob
This knob offsets the center frequency of the IF
passband when rotated from its "normal" (center) po-
sition. This control functions in all modes except FM.
When the IDBT System is activated by pressing the
[ IDBT ] button on the Shuttle Jog, the EDSP (Con-
tour) filter's passband offset changes according to this
knob's setting.
46 . WIDTH Knob
This knob, when turned from center, reduces the
overall IF bandwidth from either the lower or upper side,
from the maximum selected by the [ BANDWIDTH ] but-
tons.
When the IDBT feature is activated by pressing the
[ IDBT ] button on the Shuttle Jog, the EDSP (Con-
tour) filter's passband width is reduced according to
this knob's setting.
C
ANEL ONTROLS
page 27