Hearth and Home Technologies Cinch Pipe & Termination Cap System Installation Instructions Manual page 4

Vent depth is measured from the back of the appliance to the outer edge of the exterior wall. See Table 1 and Figure 1.
Appliance
Novus
NXT
Caliber
Maxus
GNTC50
Designer*
Titan
6000
8000
Olympian
Multisided
Gem
SL units
ICON
GDST5244I**
* Top vented appliance - Designer needs a DVP12 after the elbow.
** GDST5244I requires a DVP12 and DVP6 after the elbow.
4 Hearth & Home Technologies Inc. • Cinch Pipe & Term Caps • 4033-900 Rev K • 05/05
TRAP CAP SPECIFICATION CHART
DVP-TRAPK1 DVP-TRAP1
Top Vent Rear Vent
Depth Depth
4-1/2 in. to 6-1/4 in. 3-1/2 in. to 4-3/4 in.
4-1/8 in. to 5-7/8 in. 4-5/8 in. to 6-3/8 in.
4-1/8 in. to 5-7/8 in. 3-5/8 in. to 5-3/8 in.
4-1/2 in. to 6-1/4 in. 4-1/8 in. to 5-7/8 in.
5 in. to 6-3/4 in. 4-7/8 in. to 6-5/8 in.
4 in. to 5-3/4 in. 5-3/4 in. to 7-1/2 in.
3-1/2 in. to 5-1/4 in.
2-3/4 in. to 4-1/2 in. 3-1/8 in. to 4-7/8 in.
2-3/4 in. to 4-1/2 in. 3-1/8 in. to 4-7/8 in.
3-1/2 in. to 5-1/4 in.
7-1/2 in. to 9-1/4 in. 3-1/8 in. to 4-7/8 in.
4-1/2 in. to 6-1/4 in.
N/A 3-1/8 in. to 4-7/8 in.
3-1/2 in. to 5-1/4 in.
4 in. to 5-3/4 in.
Figure 1 - Measuring Required Vent Depth
DVP-TRAPK2
Top Vent
Depth
7 in. to 11 in.
6-1/2 in. to 10-1/2 in.
6-1/2 in. to 10-1/2 in.
6-7/8 in. to 10-7/8 in.
7-3/8 in. to 11-3/8 in.
6-3/8 in. to 10-3/8 in.
N/A 6 in. to 10 in.
5-1/4 in. to 9-1/4 in.
5-1/4 in. to 9-1/4 in.
N/A 6 in. to 10 in.
10 in. to 14 in.
N/A 7 in. to 11 in.
N/A
N/A 6-1/2 in. to 10-1/2 in.
N/A 6-3/4 in. to 7-3/4 in.
Table 1
DVP-TRAP2
Rear Vent
Depth
5-1/2 in. to 9-1/2 in.
7-1/4 in. to 11-1/4 in.
6-1/4 in. to 10-1/4 in.
6-3/4 in. to 10-3/4 in.
7-3/8 in. to 11-3/8 in.
8-1/8 in. to 12-1/8 in.
N/A
5-5/8 in. to 9-5/8 in.
5-5/8 in. to 9-5/8 in.
N/A
5-5/8 in. to 9-5/8 in.
N/A
5-5/8 in. to 9-5/8 in.
N/A
N/A