Multiroom Setup; Multiroom Operation - Harman Kardon AVR 330 Owner's Manual

Multiroom Operation

Multiroom Setup

Once the audio and IR link connections have
been made, the AVR needs to be configured for
multiroom operation using the steps below.
Press the OSD button to bring the
(Figure 1) to the screen. Press
T E R M E N U
the button twice, until the on-screen
cursor is next to the
MULTI-ROOM
Press the Set button to enter the
menu (Figure 12).
MULTI-ROOM
* M U L T I - R O O M *
M U L T I - R O O M : O F F
M U L T I I N : F M
M U L T I V O L : 2 5 d B
B A C K T O M A S T E R M E N U
Figure 12
When the menu appears, the
MULTI-ROOM
on-screen cursor will be at the
MULTI-
line. Since this line is used to turn the
ROOM
system on and off, do not make an adjustment
here unless you wish to turn the system on at
this time. To turn the system on, press the
ton so that is shown. If you do not wish
O N
to turn the system on at this time or to proceed
to the next step, press the Button
so that the on-screen cursor is next to the
line.
MULTI I N
At the line, press the
MULTI I N
until the desired Audio/Video input to
the multi-room system appears in the highlight-
ed video. When the selection has been made,
press the button once so that the
screen cursor is next to the
MULTI VOL
At the
MULTI VOL
tons or hold them pressed until the
desired volume level for the multi-room system
is entered. DO NOT use the regular volume con-
trol knobs for this setting. When all settings for
M A S-
the multiroom setup have been made, press the
buttons once so that the on-screen
line. cursor is next to the
line and press the Set button
MENU
you have no other adjustments to make, press
the OSD button
Multiroom Operation
When operating the AVR from a remote room
location where an IR sensor link has been con-
nected to the AVR's rear panel Multiroom IR
Input , you may use either the Main remote
control or the Zone II remote. To turn on the
multiroom feed, press any of the Input
Selector buttons on the Zone II remote
or the Main remote
Press the AVR Selector
unit on to the last source, or any of the other
Selector buttons to turn on to a specific source.
As long as an IR feed to the AVR has been
established from the remote room, using any of
but-
the buttons on either remote will control the
remote location volume
tuner frequency
once
preset or mute the output
If the Remote IR Output jack
AVR is connected to an IR Input jack on compat-
buttons
/
ible Harman Kardon audio components such as
CD, DVD or cassette players, the transport func-
tions of those machines may also be
controlled using the Transport Controls
on-
line.
control.
To turn the system off from the remote room,
press the Power-Off button
Remember that the AVR may be turned on or off
from the remote room regardless of the
system's operation or status in the main room.
NOTE: When the tuner is selected as the source
for the remote zone, any change to the frequen-
cy or preset will also change the station being
listened to in the main room, if the tuner is in
use there. Similarly, if someone in the main room
changes the station, the change will also impact
the remote room.
To activate the feed to the remote room, press
the Multiroom button
Next, press the Set button
buttons to turn the multiroom feed on or
off. When the multiroom system is on, the Main
Information Display
. Press the Set button
MULTI O N
to enter the setting.
line, press the but- When the multiroom system is turned on, the
/
input selected using the Multiroom Menu will be
fed to the Multiroom Output jacks
rear panel. The volume will be as set in the same
menu, although it may also be adjusted using an
optional IR sensor and the Zone II remote in the
remote location or on the optional audio power
amplifier connected to the Multiroom Output
BACK T O MASTER
. If jacks
Once the multiroom system is turned on, it will
to exit the menu system.
remain on even if the AVR is placed in the
Standby mode in the main room by pressing the
Power Off Button
Control
multiroom system from the main listening room,
when the AVR is on press the Multiroom but-
ton
Information Display
.
MULTI OFF
to turn the
Even when the AVR is turned off (to Standby
mode) and the multiroom system is turned off
too, the multiroom system may be turned on at
any time by pressing the Multiroom button
, change the
, change the tuner
.
on the
on either remote
.
on the remote.
. Press the
/
or OSD will display
twice
.
or the System Power
on the front panel. To turn off the
and then the Set button
buttons so that the Main
/
or OSD will display
.
, or any of the Selector buttons
in the remote room.
MULTIROOM 37
on the
. Press the