Gas Conversion Kits - Lennox Hearth Products ELITE E36ODGNE Installation Instructions Manual

GAS CONVErSION KItS

WArNING: tHIS CONVErSION KIt SHALL BE
INStALLEd By A QuALIFIEd SErVICE AGENCy
IN ACCOrdANCE WItH tHE MANuFACturEr'S
INStruCtIONS ANd ALL APPLICABLE COdES ANd
rEQuIrEMENtS OF tHE AutHOrIzEd HAVING
jurISdICtION. IF tHE INFOrMAtION IN tHESE
INStruCtIONS IS NOt FOLLOWEd ExACtLy, A
FIrE, ExPLOSION Or PrOduCtION OF CArBON
MONOxIdE MAy rESuLt CAuSING PrOPErty
dAMAGE, PErSONAL INjury Or LOSS OF LIFE.
tHE INStALLAtION IS NOt PrOPEr ANd COM-
PLEtE uNtIL tHE OPErAtION OF tHE CONVErtEd
APPLIANCE IS CHECKEd AS SPECIFIEd IN tHE
OWNEr INStruCtIONS SuPPLIEd WItH tHE KIt.
tHE QuALIFIEd SErVICE AGENCy PErFOrMING
tHIS INStALLAtION ASSuMES rESPONSIBILIty
FOr tHIS CONVErSION.
In Canada:
tHE CONVErSION SHALL BE CArrIEd Out
IN ACCOrdANCE WItH tHE rEQuIrEMENtS
OF tHE PrOVINCIAL AutHOrItIES HAVING
jurISdICtION ANd IN ACCOrdANCE WItH
tHE rEQuIrEMENtS OF tHE CAN-B49.
ANd .2 INStALLAtION COdE.
LA CONVErSION dEVrA ÊtrE EFFECtuÉE
CONFOrMÉMENt Aux rECOMMANdA-
tIONS dES AutOrItÉS PrOVINCIALES
AyANt jurIdICtION Et CONFOrMÉMENt
Aux ExIGENCES du COdE d'INStALLAtION
CAN-B49. Et.2.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete the
task including labeling that must be affixed to
ensure safe operation.
Kit part numbers are listed here and the follow-
ing steps detail the conversion procedure.
AVErtISSEMENt: CEt ÉQuIPEMENt dE CONVErSION
SErA INStALLÉ PAr uNE AGENCE QuALIFIÉE dE
SErVICE CONFOrMÉMENt Aux INStruCtIONS du
FABrICANt Et tOutES ExIGENCES Et COdES APPLI-
CABLES dE L'AutOrISÉS AVOIr LA jurIdICtION. SI
L'INFOrMAtION dANS CEttE INStruCtION N'ESt PAS
SuIVIE ExACtEMENt, uN FEu, ExPLOSION Ou PrOduC-
tION dE PrOtOxydE dE CArBONE PEut rÉSuLtEr
LE dOMMAGES CAuSEr dE PrOPrIÉtÉ, PErtE Ou
BLESSurE PErSONNELLE dE VIE. L'AGENCE QuALI-
FIÉE dE SErVICE ESt ESPONSABLE dE L'INStALLAtION
PrOPrE dE CEt ÉQuIPMENt. L'INStALLAtION N'ESt
PAS PrOPrE Et COMPLÉtE juSQu'à L'OPÉrAtION
dE L'APPArEIL CONVErtI ESt CHÉQuE SuIVANt LES
CrItèrES ÉtABLIS dANS LES INStruCtIONS dE PrO-
PrIÉtAIrE PrOVISIONNÉES AVEC L'ÉQuIPEMENt.
Step . Turn off the gas supply to the ap-
pliance.
Step 2. Carefully remove the logs. Exercise
care so as not to break the logs.
Step 3. Refer to Figure 19.
Remove the burner assembly with attached
venturi tube.
N t a r u l a o t P o r a p e n G s a C
K t i
M o e d s l
U t i n y T e p
N . o
E 6 3 O D G G C K D - B 0 8 7 P
E 2 4 O D G G C K D - B 0 8 7 P
P o r a p e n o t N t a r u l a G s a C o
M d o l e N . o U t i n y T e p
E 6 3 O D G G C K D - B 1 0 4 N
E 2 4 O D G G C K D - B 1 0 4 N
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
remove Clip
Shutter
Opening
o v n r e i s n o
a C l a t g o N . o
H 9 4 6 1
H 9 4 6 1
Orifice
v n r e i s n o K t i
Figure 19
a C l a t g o
N . o
H 9 4 5 1
H 9 4 5 1
remove tube
regulator
5