Icom IC-V80 Quick Manual

QUICK GUIDE
VHF TRANSCEIVERS
iV80/iV80E
UHF TRANSCEIVERS
iU80/iU80E
This sheet describes only basic operations. For more detailed instructions, go to our web site (URL: http://www.icom.co.jp/world/
index.html) to view or download the full instruction manual.
In the instruction manual, some options or some functions may not be available for your version. Please ask your dealer for details.
■
Precautions
RDANGER! USE
the battery only with the transceiver
for which it is specifi ed. Never use a battery with any other
equipment, or for any purpose that is not specifi ed in the in-
struction manual.
RDANGER! NEVER
short the terminals of the bat-
tery pack.
RWARNING RF EXPOSURE!
This device emits
Radio Frequency (RF) energy. Caution should be observed
when operating this device. If you have any questions regarding
RF exposure and safety standards, please refer to the Federal
Communications Commission Office of Engineering and Tech-
nology's report on Evaluating Compliance with FCC Guidelines
for Human Radio Frequency Electromagnetic Fields (OET Bulle-
tin 65).
RWARNING! NEVER
hold the transceiver so that the
antenna is very close to, or touching exposed parts of the body,
especially the face or eyes, while transmitting. The transceiver
will perform best if the microphone is 5 to 10 cm (2 to 4 inches)
away from the lips and the transceiver is vertical.
RWARNING! NEVER
operate the transceiver with
a headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the
volume level or discontinue use.
RWARNING! NEVER
operate the transceiver while
driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.
RWARNING! NEVER
operate or touch the trans-
ceiver with wet hands. This may result in an electric shock or
damage the transceiver.

■ Battery cautions

D For the BP-264 Ni-MH battery
R DANGER! NEVER incinerate used battery packs. Internal
battery gas may cause an explosion.
R DANGER! NEVER immerse the battery pack in water.
If the battery pack becomes wet, be sure to wipe it dry BE-
FORE attaching it to the transceiver.
CAUTION: Always use the battery within the specified tem-
perature range, –5˚C to +60˚C (+23˚F to +140˚F). Using the
battery out of its specifi ed temperature range will reduce the
battery's performance and battery life.
CAUTION: Shorter battery life could occur if the battery is left
completely discharged, or in an excessive temperature en-
vironment (above +55˚C; +131˚F) for an extended period of
time. If the battery must be left unused for a long time, it must
be detached from the radio after charging. Keep it safely in a
cool dry place at the following temperature range:
–20˚C to +45˚C (–4˚F to +113˚F) (up to a month)
–20˚C to +35˚C (–4˚F to +95˚F) (up to six months)
–20˚C to +25˚C (–4˚F to +77˚F) (up to a year*)
* We recommend charging the battery pack every 6 months.
Clean the battery terminals to avoid rust or bad contact.
Keep battery terminals clean. It's a good idea to occasionally
clean them.
If your Ni-MH battery pack seems to have no capacity, even
after being charged, completely discharge it by leaving the
power ON overnight. Then, fully charge the battery pack again.
If the battery pack still does not retain a charge (or only very lit-
tle charge), a new battery pack must be purchased.
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.
• Recommended temperature range for charging:
between +10°C and +40°C (+50˚F to +104˚F) (rapid charge:
with BC-191) or between 0°C and +45°C (+32˚F to +113˚F)
(regular charge: with BC-192)
• Use only the supplied charger or optional charger (BC-191
for rapid charging, BC-192 for regular charging). NEVER
use other manufacturers' chargers.
The battery pack contains a rechargeable battery.
Charge the battery pack before fi rst operating the transceiver,
or when the battery pack becomes exhausted.
If you want to prolong the battery life, the following points
should be observed:
• Avoid over charging. The charging time period should be
less than 48 hours.
• Use the battery pack until it becomes almost completely ex-
hausted, under normal conditions. We recommend battery
charging just when transmitting becomes impossible.
D For the BP-265 Li-ion battery
R DANGER! Use and charge only specified Icom battery
packs with Icom radios or Icom chargers. Only Icom battery
packs are tested and approved for use with Icom radios or
charged with Icom chargers. Using third-party or counterfeit
battery packs or chargers may cause smoke, fire, or cause
the battery to burst.
R DANGER! DO NOT hit or otherwise impact the battery. Do not
use the battery if it has been severely impacted or dropped, or if
the battery has been subjected to heavy pressure. Battery dam-
age may not be visible on the outside of the case. Even if the sur-
face of the battery does not show cracks or any other damage, the
cells inside the battery may rupture or catch fi re.
R DANGER! NEVER use or leave battery pack in areas with
temperatures above +60˚C (+140˚F). High temperature buildup
in the battery, such as could occur near fi res or stoves, inside
a sun heated car, or in direct sunlight may cause the battery
to rupture or catch fi re. Excessive temperatures may also de-
grade battery performance or shorten battery life.

■ Belt clip

To attach the belt clip:
Slide the belt clip in the direction of the arrow until the belt clip
locks in place, and makes a 'click' sound.
Belt clip
Battery pack/case
Thank you for purchasing the IC-V80/IC-V80E
VHF TRANSCEIVERS
or IC-U80/IC-U80E with Icom's state of
UHF TRANSCEIVERS
the art technology.
Please read all instructions carefully before using.
DO NOT
operate the transceiver near unshielded electri-
cal blasting caps or in an explosive atmosphere.
DO NOT
push [PTT] when not actually intending to transmit.
BE CAREFUL!
The transceiver will become hot when
operating it continuously for long periods of time.
DO NOT
use or place the transceiver in direct sunlight or
in areas with temperatures below –20°C (–4°F) or above
+60°C (+140°F).
KEEP
the transceiver out of the reach of children.
DO NOT
use harsh solvents such as benzine or alcohol
when cleaning, as they will damage the transceiver's surfaces.
DO NOT
disassemble or modify the transceiver. The
transceiver warranty does not cover any problems caused
by unauthorized modifi cation.
KEEP
the transceiver away from heavy rain, and never im-
merse it in the water. The transceiver meets IP54* require-
ments for dust-protection and splash resistance. However,
once the transceiver has been dropped, dust-protection and
splash resistance cannot be guaranteed because of possible
damage to the transceiver's case or the waterproof seal.
* Only when the battery pack or case, antenna and jack cover are
attached.
Even when the transceiver power is OFF, a slight current
still flows in the circuits. Remove the battery pack or case
from the transceiver when not using it for a long time. Other-
wise, the battery pack or installed dry cell batteries will be-
come exhausted.
R DANGER! DO NOT expose the battery to rain, snow, sea-
water, or any other liquids. Do not charge or use a wet battery.
If the battery gets wet, be sure to wipe it dry before using.
R DANGER! NEVER incinerate a used battery pack since in-
ternal battery gas may cause it to rupture, or may cause an
explosion.
R DANGER! NEVER solder the battery terminals, or NEVER
modify the battery pack. This may cause heat generation, and
the battery may burst, emit smoke or catch fi re.
R DANGER! If fl uid from inside the battery gets in your eyes,
blindness can result. Rinse your eyes with clean water, with-
out rubbing them, and see a doctor immediately.
R WARNING! Immediately stop using the battery if it emits an
abnormal odor, heats up, or is discolored or deformed. If any of
these conditions occur, contact your Icom dealer or distributor.
R WARNING! Immediately wash, using clean water, any part
of the body that comes into contact with fluid from inside the
battery.
R WARNING! NEVER put the battery in a microwave oven,
high-pressure container, or in an induction heating cooker.
This could cause a fire, overheating, or cause the battery to
rupture.
CAUTION: Always use the battery within the specified tem-
perature range, –20˚C to +60˚C (–4˚F to +140˚F). Using the
battery out of its specifi ed temperature range will reduce the
battery's performance and battery life.
CAUTION: Shorter battery life could occur if the battery is left
fully charged, completely discharged, or in an excessive tem-
perature environment (above +50˚C; +122˚F) for an extended
period of time. If the battery must be left unused for a long time,
it must be detached from the radio after discharging. You may
use the battery until the battery icon shows half-capacity, and
then keep it safely in a cool dry place at the following tempera-
ture range:
–20˚C to +50˚C (–4˚F to +122˚F) (up to a month)
–20˚C to +35˚C (–4˚F to +95˚F) (up to three months)
–20˚C to +20˚C (–4˚F to +68˚F) (up to a year)
D Charging caution
R DANGER! NEVER charge the battery pack in areas with
extremely high temperatures, such as near fi res or stoves, in-
side a sun-heated vehicle, or in direct sunlight. In such en-
vironments, the safety/protection circuit in the battery will
activate, causing the battery to stop charging.
R WARNING! DO NOT charge or leave the battery in the
battery charger beyond the specifi ed time for charging. If the
battery is not completely charged by the specifi ed time, stop
charging and remove the battery from the battery charger.
Continuing to charge the battery beyond the specified time
limit may cause a fire, overheating, or the battery may rup-
ture.
R WARNING! NEVER insert the transceiver (battery at-
tached to the transceiver) into the charger if it is wet or soiled.
This could corrode the battery charger terminals or damage
the charger. The charger is not waterproof.
CAUTION: DO NOT charge the battery outside of the spec-
ified temperature range: BC-193 (+10˚C to +40˚C; +50˚F to
+104˚F). Icom recommends charging the battery at +20˚C
(+68˚F). The battery may heat up or rupture if charged out of
the specified temperature range. Additionally, battery perfor-
mance or battery life may be reduced.
The supplied battery pack, charger, and AC adapter differ, or
no supplied depending on the version.
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.
To detach the belt clip:
q Remove the battery pack or case from the transceiver, if it
is attached.
w Lift the tab up (q), and slide the belt clip in the direction of
the arrow (w).
w
q

■ Battery pack or case

NEVER remove or attach the battery pack or case when the transceiver is wet or soiled. This may result in water or dust get-
ting into the transceiver or the battery pack or case, and may result in them being damaged.
To attach the battery pack or case:
q Fit the battery pack or
q Battery pack
or
case in the direction
battery case
of the arrow (q), and
then close it.
w
w Hook the latch until it
Latch
makes a 'click' sound
(w).
■ Panel description— Front panel
w
e
Speaker
r
q
Microphone
Function
display
t
y
u
Keypad
i
q PTT SWITCH [PTT]
➥ Hold down to transmit, release to receive.
For IC-V80E only
➥ Quickly push [PTT] once, then immediately hold down
[PTT] again for 1 or 2 seconds, to transmit a 1750 Hz
tone burst signal.
w ANTENNA CONNECTOR
Connect an antenna here.
e CONTROL DIAL [VOL]
➥ Adjust the volume level.
➥ While in the Set mode, or Initial Set mode, rotate to se-
lect a desired item, option or value.
r EXTERNAL SPEAKER/MICROPHONE JACKS [SP MIC]
Accepts an optional speaker-microphone, plug adapter
cable or cloning cable connector. The internal microphone
and speaker will not function when an option is connected.
Be sure to turn OFF the transceiver power, before con-
necting or disconnecting optional equipment to or from
the [SP/MIC] jack.
t MONITOR KEY [MONI]
➥ Hold down to temporarily open the squelch to monitor
the operating frequency.
➥ While holding down this key, push [Y] or [Z] to adjust
the squelch level.
➥ Enters or sends the DTMF code 'A.'
y POWER KEY [ ]
Hold down for 1 second to turn the power ON or OFF.
u UP/DOWN KEYS [Y]/[Z]
➥ Push to change the operating frequency.
➥ During memory mode, push to select a memory channel.
➥ While scanning, push to change the scanning direction.
➥ While holding down [MONI], push to adjust the squelch level.
➥ While in the Set mode, or Initial Set mode, push to se-
lect a setting item.
➥ [Y] enters or sends the DTMF code 'B.'
➥ [Z] enters or sends the DTMF code 'C.'
i VFO/MEMORY/CALL KEY [VFO/MR/CALL]
➥ Push to sequentially select the VFO mode, memory
mode, a Call channel or a weather channel*.
*For only USA version.
➥ After pushing [FUNC](M), push to enter the memory
programming mode.
➥ After pushing [FUNC](M), hold down for 1 second to
transfer a channel contents to a memory channel, or to
the VFO mode.
➥ Enters or sends the DTMF code 'D.'
■ Panel description— Function display
q w e r t y
!5
!4
!3
!2 !1 !0
q BUSY ICON
➥ Appears when a signal is being received, or the squelch
is open.
➥ Blinks while the monitor function is ON.
w SIGNAL ICON
➥ Shows the strength of the received signal.
Weak RX Signal level Strong
➥ While transmitting, shows the output power level.
Low Mid High
e TONE ICONS
Appear when the tone function is turned ON, and indicate
which tone function is in use.
" " Repeater tone encoder
" " and " " DTCS encoder (Only TX)
D
" " CTCSS squelch function
" " DTCS squelch function
D
" " and " " CTCSS Pocket beep function
" " and " " DTCS Pocket beep function
D
r MEMORY ICON
➥ Appears when the memory mode is selected.
➥ Blinks during a memory scan.
t FREQUENCY READOUT
➥ Displays the operating frequency, memory channel, Set
modes contents and a variety of other information.
• The decimal point blinks during a scan.
➥ While in the memory mode, the programmed memory
name is displayed.
To remove the battery pack or case:
Be careful! The latch is tightly locked, so use caution
when releasing it. DO NOT use your fingernail. Use the
edge of a coin or screwdriver tip to carefully release it.
➥ Unhook the latch (z), and
x then lift up the battery pack
or case in the direction of
the arrow (x).
z
D KEYPAD
➥ While in the VFO mode, push to enter numbers for frequen-
enter numbers for frequen-
cy input. cy input.
➥ While in the memory mode, push to enter numbers to select
enter numbers to select
a a memory channel. memory channel.
➥ Push to enter or send a DTMF code.
➥ To activate the second function of a key, fi rst push [FUNC](M),
and then push the key.
[1] • [ TONE](1)
➥ Numeric input and DTMF code: '1'
nput and DTMF code: '1'
➥ After pushing [FUNC](M), selects the Tone function.
[2] • [VOX](2)
➥ Numeric input and DTMF code: '2'
nput and DTMF code: '2'
➥ After pushing [FUNC](M), turns the VOX function ON
or OFF*.
* Only when an optional headset and plug adapter are con-
nected.
[3] • [T.SCAN](3)
➥ Numeric input and DTMF code: '3'
nput and DTMF code: '3'
➥ After pushing [FUNC](M), starts a tone scan.
[4] • [DUP](4)
➥ Numeric input and DTMF code: '4'
nput and DTMF code: '4'
➥ After pushing [FUNC](M), selects minus duplex, plus
duplex, or simplex operation.
[5] • [SCAN](5)
➥ Numeric input and DTMF code: '5'
nput and DTMF code: '5'
➥ After pushing [FUNC](M), starts a scan.
[6] • [SKIP](6)
➥ Numeric input and DTMF code: '6'
nput and DTMF code: '6'
➥ After pushing [FUNC](M), sets or cancels the skip
setting.
[7] • [PRIO](7)
➥ Numeric input and DTMF code: '7'
nput and DTMF code: '7'
➥ After pushing [FUNC](M), starts a priority watch.
[8] • [SET](8)
➥ Numeric input and DTMF code: '8'
nput and DTMF code: '8'
➥ After pushing [FUNC](M), enters the Set mode.
[9] • [H/M/L](9)
➥ Numeric input and DTMF code: '9'
nput and DTMF code: '9'
➥ After pushing [FUNC](M), selects the output power
of high, mid or low.
[0] • [DTMF-M](0)
➥ Numeric input and DTMF code: '0'
nput and DTMF code: '0'
➥ After pushing [FUNC](M), enters the DTMF memory
mode.
[M] • [FUNC](M)
➥ DTMF code: '
DTMF code: 'M (indication: E)' '
➥ Push to access the second function of other keys.
[# ENT] • [ ](# ENT)
➥ DTMF code: '
DTMF code: '# (indication: F)' '
➥ After entering a frequency, push to save it.
➥ Push to exit the Set mode or Initial Set mode.
➥ After pushing [FUNC](M), hold down for 1 second to
turn the Key Lock function ON or OFF.
y BATTERY ICONS
➥ "
" appears when the battery pack or case is attached.
➥ " " appears when the battery is nearing exhaustion.
u Charging the battery pack, or replacing the batteries in
the case is necessary.
i
u KEY LOCK ICON
o
Appears when the Key Lock function is ON.
i VOX ICON
Appears when the VOX function is ON.
o POWER ICON
➥ " H" appears when high power is selected.
➥ " M" appears when mid power is selected.
➥ " L" appears when low power is selected.
!0 MEMORY CHANNEL NUMBER READOUT
➥ Displays the selected memory channel number.
➥ "C" appears when the Call channel is selected.
!1 AUTO POWER OFF ICON
Appears when the Auto Power OFF function is ON.
!2 DUPLEX ICON
➥ "+" appears when plus duplex is selected.
➥ "–" appears when minus duplex is selected.
• No icon is displayed when simplex is selected.
!3 SKIP ICON
Appears when the selected memory channel is set as a
skip channel.
!4 FUNCTION ICON
Appears when a second function can be accessed.
!5 TRANSMIT ICON
Appears while transmitting.