Harman Kardon AVR 354 Owner's Manual page 12

REAR-PANEL CONNECTIONS
• The Analog 1 and 2 connectors don't physically line up with
any analog video inputs. Consider using them for audio-only
devices, such as a CD player or cassette tape deck.
• The Analog 2 and 4 inputs are each associated with a set of
outputs. Consider using the Analog 2 connectors for an audio
recorder, and the Analog 4 connectors for a video recorder
(along with the Video 2 connectors).
• You may optionally connect a source to both an analog and
digital audio input. This is useful for making recordings, for
multizone applications or simply as a backup.
Analog 2 and 4 Outputs:
outputs to the analog audio inputs of a recording device. A signal is
available at these outputs whenever an analog audio source is playing.
However, the AVR 354 does not convert digital audio sources to analog
for recording.
Coaxial 1/2 and Optical 1/2/3 Digital Audio Inputs:
source has a compatible digital audio output, and if you are not using
an HDMI connection for audio for the device, connect it to one of these
jacks to hear digital audio formats, such as Dolby Digital, DTS and linear
PCM. Use only one type of digital audio connection for each source.
Coaxial Digital Audio Output:
recorder, connect a coaxial digital audio output to the recorder's input
for improved recording quality. Only PCM digital audio signals are
available for recording.
The Bridge II Input:
Connect the included Harman Kardon
docking station to this input for use with most docking
iPod models, 4G and later (not included). Make sure the receiver is
turned off (in Standby mode) when connecting The Bridge II.
6-/8-Channel Inputs:
Connect the multichannel analog audio
outputs of a DVD-Audio, SACD
(or any other external decoder) to these jacks to enjoy these formats.
NOTE: When the multichannel player has an onboard digital
decoder, it is not necessary to connect it to the 6-/8-Channel
Analog Audio Inputs. Only a digital audio connection (HDMI,
coaxial or optical) is needed.
Zone 2 Audio Outputs:
to power the speakers in the remote zone of a multizone system. When
these jacks are used, it is possible to have a full 7.1-channel system in
the main listening room at the same time the multizone system is in use.
Component Video 1, 2 and 3 Inputs:
DVD player or HDTV tuner) has analog component video (Y/Pb/Pr)
capability, and if you are not using an HDMI connection for the device,
then connect the component video outputs of the source to one of the
sets of component video inputs. Do not make any other video connec-
tions to that source.
Component Video Monitor Outputs:
the Component Video Inputs and your television or video display is
component-video-capable, and if you are not connecting the HDMI
12 12
Connect either of these analog audio
If a source is also an audio
™ , Blu-ray Disc ™ or HD-DVD
Connect these jacks to an external amplifier
If a video source (e.g.,
If you are using one of
Output to your display, connect these jacks to the corresponding inputs
on your video display.
NOTES:
• Due to copy-protection restrictions, there is no output at
the Component Video Monitor Outputs for copy-protected
sources.
• Composite and S-video signals are upscaled to as high as
1080i and available at these outputs. If your video display's
best connection is component video, it is the only video
connection required from the AVR to the display.
RS-232 Serial Port:
your personal computer in case we offer a software upgrade for the
receiver at some time in the future.
RS-232 Mode:
unless the AVR 354 is being upgraded.
If a
RS-232 Reset:
A standard processor reset is performed by pressing and holding the
front-panel OK Button.
Switched AC Accessory Outlet:
cord of one source device into this outlet, and it will turn on whenever
you turn on the receiver. Do not use a source that consumes more than
50 watts of power.
AC Power Input:
AC power cord into this receptacle and into an unswitched wall outlet.
™ player
This specialized connector may be used with
Leave this switch popped out in the Operate position
This switch is only used during a software upgrade.
You may plug the AC power
After you have made all other connections, plug the
12
12