Sign in today to find solutions:

Don't have an account? Sign up

Harbor Freight Tools CEN-TECH 94233 Assembly And Operating Instructions Manual

Harbor freight tools thermometer user manual.

 
flexible infrared
assembly and operating instructions
read this material before using this product.
failure to do so can result in serious injury.
saVe this manual.
Copyright
2006 by Harbor Freight Tools
©
tained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
for technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10c
thermometer
model
Visit our website at: http://www.harborfreight.com
. All rights reserved. No portion of this manual or any artwork con-
®
94233

Summary of Contents

  • Page 1

    Copyright 2006 by Harbor Freight Tools © tained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.

  • Page 2

    Read all instructions before using this tool! Keep work area clean. Cluttered areas invite injuries. Observe work area conditions. Do not use the Flexible Infrared Thermometer in damp or wet locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases or liquids.

  • Page 3

    When unpacking, check to make sure the parts on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.

  • Page 4

    Note: You will need to set the “C” or “F” key (5) to establish an LCD readout in either Fahrenheit or Celsius. Refer to the Assembly Drawing on page 8. The Thermometer automatically powers ON when the Measuring Key (7) is selected. The Thermometer will power OFF automatically approximately 7 seconds after the Measuring Key (7) is released.

  • Page 5

    Figure 4 Measuring Operation Hold the Thermometer in your hand, point the Laser Pointer (2) and Infrared Sensor (1) toward the object to be measured. The Thermometer will automatically compensate for temperature deviations from ambient temperature. Note: It will take up to 30 minutes to adjust to wide ambient temperature measurements, followed by high temperature measurements.

  • Page 6

    9 Volt Battery (9) Recommendations and Reminders This Thermometer is not recommended for use in measuring a shiny or polished metal surface such as stainless steel, aluminum, etc.) To compensate, cover the surface to be measured with masking tape or flat black paint. Allow the tape to reach the same temperature as the material underneath.

  • Page 7

    Emissivity Most organic materials and painted or oxidized surfaces have an emissivity of 0.95 (pre-set in the unit). Inaccurate readings will result from measuring a shiny or polished metal surface. See recommendations on page 6 for obtaining an accurate reading and refer to the chart below.

  • Page 8

    Parts List Part # Description Infrared Sensor Laser Pointer Beam LCD Display Laser Key Celsius or Fahrenheit Select Key Backlight Select Key Measuring Key Battery Compartment Carrying Case (no shown) Note: No replacement parts available for this unit. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.

  • Page 9

    90 day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: