Advertisement
6" CUTOFF SAW
Model 41453
ASSEMBLY AND
OPERATING INFORMATION
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
©
®
Copyright
1999 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353.
MANUAL REVISED 01/02
Advertisement
Table of Contents
Related Manuals for Chicago Electric 41453
Summary of Contents for Chicago Electric 41453
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions please call 1-800-444-3353. MANUAL REVISED 01/02...
-
Page 2: Specifications Table
USE EYE, HEARING, AND BREATHING PROTECTION. Wear ANSI approved safety impact eyeglasses, hearing protectors, dust masks or respirator when using this product. ANSI approved safety impact eyeglasses, hearing protectors, dust masks and respirators are available from Harbor Freight Tools. SKU 41453 For technical questions, please call 1-800-444-3353. -
Page 3: Specific Product Warnings And Precautions
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry, and keep cutoff grinding wheels clean and sharp for better and safer performance. - Page 4 To comply with the National Electric Code (NFPA70), and to provide additional protection from the risk of electrical shock, the Cut-Off Saw should only be connected to a 115 Volt, 3 prong, electrical outlet that is protected by a Ground Fault Circuit Interrupter (GFCI).
- Page 5 NOTE: Performance of this tool may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. MAINTAIN A SAFE WORK ENVIRONMENT. Do not use the Cut-Off Saw in or near damp or wet areas. Do not expose this tool to rain. Keep the work area well lit.
-
Page 6: Assembly Instructions
When unpacking, check to make sure all parts listed and shown on pages 10 and 11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. - Page 7 Spindle, and hold it firmly. Use Wrench (46) to remove (CCW) the Outer Flange (1) from the Spindle. Note: This saw accepts wheels with 2 different arbor sizes: 5/8”, 7/8”. 5/8” Arbor: Place the Wheel directly onto the spindle without using the Inner Flange (3).
-
Page 8: Operating Instructions
For additional references to the parts listed below, refer to pages 10 and 11 of this manual. WARNING! Do not use unapproved accessories. Do not use circular saw blades or wire brushes on this tool. Do not use any accessory except 6”... -
Page 9: Inspection, Maintenance, And Cleaning
If there are large scratch marks in the Carbon Brushes, or parts of the Carbon Brushes have broken off, replace both Carbon Brushes immediately with approved replacement Carbon Brushes from Harbor Freight Tools. To reinstall the Carbon Brushes, insert them into the Brush Holders. Turn the Carbon Brushes vertically so they will fit into the Brush Holders. -
Page 10: Parts List
Do not use solvents to wipe off the Cut-Off Saw, as damage may result. If necessary, wipe with a damp cloth. You may use a mild detergent. Do not introduce water into the electric motor through the motor vents. Once clean, lubricate all moving parts with a light weight oil. -
Page 11: Assembly Diagram
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 41453 For technical questions, please call 1-800-444-3353. PAGE 11...