Drill Master 90374 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Drill Master Manuals
  4. Drill
  5. 90374
  6. Assembly and operating instructions manual

Drill Master 90374 Assembly And Operating Instructions Manual

18v cordless combo pack
Hide thumbs
Table of Contents

Advertisement

Quick Links

18V CORDLESS COMBO PACK
Model 90374
Due to continuing improvements,
actual product may differ slightly from the product described herein.
Distributed exclusively by
®
Harbor Freight Tools
.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
©
®
Copyright
2003 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
REV 07l

Advertisement

Table of Contents
loading

Related Manuals for Drill Master 90374

Summary of Contents for Drill Master 90374

  • Page 1 2003 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. REV 07l...

  • Page 2: General Safety Rules

    Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. SKU 90374 PRODUCT SPECIFICATIONS " 8 & l o t "...
  • Page 3 Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. SKU 90374 ELECTRICAL SAFETY PERSONAL SAFETY...
  • Page 4 Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 90374 TOOL USE AND CARE PAGE 4 REV 03j...
  • Page 5 Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. SKU 90374 SERVICE GROUNDING WARNING!

  • Page 6: Extension Cords

    For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.) If using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure C.) SKU 90374 FIGURE B EXTENSION CORDS PAGE 6...
  • Page 7 7.1 – 12.0 12.1 – 16.0 16.1 – 20.0 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE C SKU 90374 (120 VOLT) EXTENSION CORD LENGTH Feet Feet PAGE 7 Feet...

  • Page 8: Specific Safety Rules

    Maintain labels and nameplates on the Combo Pack. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Ground this product. To comply with the National Electric Code, and to provide...
  • Page 9 There are certain applications for which these products were designed. They will do the job better and more safely at the rate for which they were intended. Do not modify these products, and do not use these products for a purpose for which they were not intended. SKU 90374 PAGE 9...
  • Page 10 When the Battery (1A) requires re-charging, a 3 to 5 hour charge allows the tool to operate at full power. Do not re-charge the Battery longer than 5 hours, as damage to the Battery and/or Flashlight or cordless tool will occur. (See Figure D.) SKU 90374 UNPACKING PAGE 10...
  • Page 11 (See Figure E, next page.) Slide the Switch Button (4C) on the Handle forward to turn “ON”. (See Figure E.) SKU 90374 Note: Always switch to a fresh battery when tool performance begins to diminish. Severe heat is most destructive to a battery; the more heat generated, the faster the battery loses power.
  • Page 12 Spring on the Battery snaps into place on the Handle. (See Figure F.) To turn on the Sander, squeeze the Switch (3D). NOTE: Always grip the Sander firmly with both hands when the tool is running. SKU 90374 LIGHT LENS...
  • Page 13 If desired, the angle of a cut may be adjusted. To do so, loosen the Hex Socket Screw (14E) located on the underside of the Sander. Tilt the Base Plate (19) to the desired angle. Then, re-tighten the Hex Socket Screw. (See Figure G.) SKU 90374 SAND PAPER (17D)
  • Page 14 Base Plate (19E), make sure to turn off the Jigsaw and disonnect the Battery (1A). Re-install a new Saw Blade, or re-adjust the Base Plate, and then re-attach the Battery. (See Figure G.) HEX KEY SOCKET (24E) SCREW (14E) FIGURE G SKU 90374 SOCKET BLADE SCREW (16E) (14E) HEX KEY (24E) HANDLE...
  • Page 15 Torque Setting Ring to the desired setting. (See Figure D.) TORQUE SETTING RING (8F) CHUCK SLEEVE CHUCK (12F) ROTATION BUTTON (33F) TRIGGER (3F) FIGURE H SKU 90374 PAGE 15 DRILL HANDLE BATTERY (1A)
  • Page 16 Drill. INSPECTION, MAINTENANCE, AND CLEANING WARNING! Always remove the Battery Pack (1A) from a tool and unplug the Battery Charger (1B) from its electrical outlet before performing any inspection, maintenance, or cleaning on the tool. SKU 90374 PAGE 16...
  • Page 17 CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 90374 PAGE 17 REV 07l...
  • Page 18 ASSEMBLY DIAGRAM - FLASHLIGHT NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 90374 PARTS LIST - FLASHLIGHT PAGE 18 Note: 1C Charger Base not shown (see page 11, Figure D)
  • Page 19 Note: 1C Charger Base not shown NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 90374 PARTS LIST - SANDER 6D 7D PAGE 19 l l i...
  • Page 20 Note: 1C Charger Base not shown NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 90374 PARTS LIST - JIGSAW PAGE 20 d i l d i l...
  • Page 21 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 90374 PARTS LIST - DRILL PAGE 21 l l a l l a...
  • Page 22 ASSEMBLY DIAGRAM - DRILL NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 90374 5F 6F PAGE 22 10F 11F REV 04f...

Table of Contents