Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. •...
Page 4
Safety Instructions DO NOT PLACE CANDLES,MOSQUITO REPELLANT,CIGA- RETTES AND ANY HEATING APPLIANCES NEAR THE PROD- UCT. • Otherwise, this may cause fire. Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire Do not install it in a badly ventilated location such as a bookcase or closet.
Page 5
Safety Instructions Do not spray cleaner directly onto the surface of the product. • Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off. Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10.
Page 6
Safety Instructions Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car. • Otherwise, this may result in electric shock or fire. When you drop the product or the case is broken, turn the power off and disconnect the power cord.
Page 7
Safety Instructions Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. If you continually move closer to the product screen, your eye- sight may be failing. To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Page 8
Safety Instructions Do not drop any objects onto the product or cause any impact to the product. • Otherwise, this may result in electric shock or fire. Do not use a humidifier or kitchen table near the product. • Otherwise, this may result in electric shock or fire. When there is a gas leak, do not touch the product or the power plug but ventilate immediately.
Page 9
Safety Instructions • Adjust the angle so that light is not reflected on the screen. • Place your arms perpendicular to your sides and allow your arms to be level with the back of the hand. • Keep your elbow at 90 degrees. •...
Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Note MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type2 Monitor &...
Introduction Cables D-Sub Cable Power Cord Others Cleaning Cloth Note Cleaning Cloth is only provided for highly polished black products as a product feature. Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on.
Page 12
Introduction Front MENU button [MENU/ ] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Customized Key[ You can customize key assignment for the Custom button according to your preferences.
Introduction Power button [ Use this button for turning the monitor on and off. Power Indicator This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. Note See PowerSaver described in the manual for further information regarding power saving functions.
Page 14
Introduction Connect the Kensington Lock cable. Fix the Kensington Lock to a desk or a heavy stationary object. Note See Connecting Cables for further information regarding cable connections. Cable holding ring • Fix the cables using the holding ring, as shown in the figure.
Connections Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. •...
Connections Using the Stand Monitor Assembly Simple Stand HAS Stand Monitor and Bottom HAS Stand A. Stand Stopper Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Page 17
Samsung is not liable for these kinds of accidents. • Samsung is not liable for product damage or personal injury when a non- VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) Insert CD into the CD-ROM drive. Click "Windows".
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System Insert your Manual CD into your CD-ROM drive.
Page 20
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. Click "Update Driver..." in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Page 21
Using the Software Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. ® ® Microsoft Windows XP Operating System...
Page 22
Using the Software Insert CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..."...
Page 23
If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Click the "Close" button then click "OK" button continually.
Page 24
Using the Software 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open"...
Page 25
Using the Software If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button. ® ® Microsoft Windows Millennium Operating System Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings"...
& Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images. For more information, refer to Help (F1) in the software program.
Using the Software How to delete the Natural Color software program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a pro- gram". Select Natural Color from the list and then click the "Add/Delete" button. MagicTune™ Installation Insert the installation CD into the CD-ROM drive. Click the MagicTune™...
Page 28
Using the Software • Windows XP Professional • Windows Vista™ ® It is recommended using MagicTune™ in Windows 2000 or later. Hardware • 32 MB Memory above • 60 MB Hard disk space above For more information, visit the MagicTune™ website. Uninstall The MagicTune™...
Page 29
Using the Software Installation Insert the installation CD into the CD-ROM drive. Click the MagicRotation installation file. Note If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MagicRotation executable file on the CD. Select installation Language, Click "Next".
Using the Software DOS based applications in Full Screen Mode will not function as per the orientation mode selected (90, 180, 270). ® Dual is not supported in Windows ‚ 98, ME, NT 4.0. MagicRotation does not provide support for 24 bits per pixel (Bit depth/Color Quality). If you are changing your Graphic Card it is recommended that you uninstall the Magi- cRotation Software before doing so.
Page 31
Using the Software Click "Yes" to begin the uninstall process. Wait until the "Uninstall Complete" dialog box appears. After uninstall restart the system to complete the uninstallation. Note Visit the MagicRotation website for technical support for MagicRotation, FAQs (questions and answers) and software upgrades.
Page 32
Using the Software System Requirements • Windows 2000 • Windows XP Home Edition • Windows XP Professional • Windows Vista™ ® It is recommended using MultiScreen in Windows 2000 or later. Hardware • 32 MB Memory above • 60 MB Hard disk space above Uninstall The Multiscreen program can be removed only by using the "Add or Remove Programs"...
Adjusting the Monitor Direct Functions AUTO When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine, Coarse and Position are adjusted automatically.
Page 34
Adjusting the Monitor When pressing the MENU button after locking the OSD This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD ad- justment lock function.
Adjusting the Monitor Note Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust Customized Key ( ) using the Direct button. Customized key You can customize key assignment for the Custom button according to your preferences. To view the operating screen displayed when pressing the [ ] button after configuring the customized key for a function, click the name of each function.
Adjusting the Monitor Brightness When OSD is not on the screen, push the Brightness ( ) button to adjust brightness. OSD Function Picture Brightness Contrast Magic- Bright Color MagicColor Color Tone Color Con- Color Effect Gamma trol Image Coarse Fine Sharpness H-Position V-Position Language H-Position V-Position...
Page 37
Adjusting the Monitor You can use the on-screen menus to change the brightness according to personal prefer- ence. MENU → → → → MENU Contrast (Not available in MagicBright mode of Dynamic Contrast.) You can use the on-screen menus to change the contrast according to personal preference. ( Not available in MagicColor mode of Full and Intelligent.
Page 38
Adjusting the Monitor MENU → → → → → MENU MagicBright Push the button to circle through available preconfigured modes. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Cus- tom, Text, Internet, Game, Sport, Movie and Dynamic Contrast.
Page 39
Color (Not available in MagicBright mode of Dynamic Contrast.) MagicColor MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. • Off - Returns to the original mode.
Adjusting the Monitor Color Tone The tone of the color can be changed and one of four modes can be selected. • Cool - Makes whites bluish. • Normal - Keeps whites white. • Warm - Makes whites reddish. • Custom - Select this mode when you want to adjust the image according to your prefer- ences.
Adjusting the Monitor Color Control Adjusts individual Red, Green, Blue color balance. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → → → → → → → → MENU Color Effect You can change the overall mood by changing the screen colors. ( Not available in MagicColor mode of Full and Intelligent.
Page 42
Adjusting the Monitor • • Grayscale • Green • Aqua • Sepia • Off - This applies an achromatic color to the screen to adjust the screen effects. • Grayscale - The default colors of black and white are displayed. •...
Page 43
Adjusting the Monitor Image Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. MENU → → → → → MENU Fine...
Page 44
Adjusting the Monitor Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). MENU → → → → → → MENU Sharpness Changes the clearance of image. ( Not available in MagicColor mode of Full and Intelligent. ) MENU →...
Page 45
Adjusting the Monitor H-Position Changes the horizontal position of the monitor's entire display. MENU → → → → → → MENU V-Position Changes the vertical position of the monitor's entire display. MENU → → → → → → MENU...
Page 46
Adjusting the Monitor Language You can choose one of nine languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. MENU → → → → → MENU...
Page 47
Adjusting the Monitor H-Position You can change the horizontal position where the OSD menu appears on your monitor. MENU → → → → → → MENU V-Position You can change the vertical position where the OSD menu appears on your monitor. MENU →...
Adjusting the Monitor Transparency Change the transparency of the background of the OSD. • • MENU → → → → → → MENU Display Time The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.
Page 49
Adjusting the Monitor • 5 sec • 10 sec • 20 sec • 200 sec MENU → → → → → → MENU Setup Reset Reverts the product settings to factory defaults. • • MENU → → → → → MENU...
Adjusting the Monitor Customized Key You can specify a function which will be activated when the Customized Key ( )is pressed. MENU → → → → → →MENU Off Timer The monitors will turn off automatically at the specified time. •...
Adjusting the Monitor MENU → → → → → → → , → MENU Image Size You can change the size of the screen displayed on your monitor. • Auto • Wide • Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals.
Page 52
Adjusting the Monitor Information Shows a video source, display mode on the OSD screen. MENU → →MENU...
Troubleshooting Self-Test Feature Check Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. Turn on the monitor.
Troubleshooting Useful Tips A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
Troubleshooting will work properly but the "Not Optimum Mode", "Recommended Mode 1440 x 900 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen.
Hardware. MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune...
Troubleshooting MagicTune™ doesn't work properly. Have you changed your PC or video graphic card? Download the latest program. The program can be downloaded http://www.sam- sung.com/monitor/magictune Did you install the program? Reboot the computer after installing the program for the first time. If a copy of the pro- gram is already installed, remove it, reboot the computer, and then install the program again.
Page 58
Troubleshooting * Contact the video card manufacturer for details. How can I set the Power Saving function? Windows XP: Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
Specifications General General Model Name SyncMaster 943AW LCD Panel Size 19 inch (48 cm) Display area 408.24 mm (H) x 255.15 mm (V) Pixel Pitch 0.2835 mm (H) x 0.2835 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M...
Page 60
Specifications VESA Mounting Interface 75 mm x 75 mm(For use with Specialty (Arm) Mounting hardware.) Environmental considerations Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug &...
ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality. ® As an ENERGY STAR Partner, SAMSUNG has deter- ® mined that this product meets the ENERGY STAR guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically.
Page 62
Specifications Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit: General General Model Name...
Page 63
Specifications Dimensions (W x H x D) / Weight (HAS Stand) 439.0 x 290.0 x 65.5 mm (17.3 x 11.4 x 2.6 inch )(Without Stand) 439.0 x 357.3 x 190.0 mm (17.3 x 14.1 x 7.5 inch )(With Stand)/ 5.2 kg (11.0 lbs) VESA Mounting Interface 75 mm x 75 mm(For use with Specialty(Arm)Mounting hardware.) Environmental considerations...
Page 64
ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality. ® As an ENERGY STAR Partner, SAMSUNG has deter- ® mined that this product meets the ENERGY STAR guidelines for energy efficiency. Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically.
Page 65
Specifications Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Hor- izontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the...
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT- LCD.
Page 67
Information During normal operation of a LCD panel, pixel image retention doesn't occur. How- ever, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display.
Page 68
Information • Recommended settings: Bright colors with little difference in luminance • Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement. The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it.
Page 69
Information Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II...
Page 70
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG http://www.samsung.com/mx (726-7864) Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar...
Page 74
Appendix Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this ma- terial. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation;...