Panasonic Viera TH-37PA60E Operating Instructions Manual page 15

Technical Information
SCART and HDMI terminal information
■
AV1 SCART terminal
(RGB, VIDEO)
Suitable inputs for AV1 include RGB (Red / Green / Blue).
Socket Earth 21
20 CVBS in (video)
CVBS out (video) 19
18 RGB status earth
CVBS earth 17
16 Status RGB
Red in 15
14 Earth
Red earth 13
12 --
Green in 11
10 --
Green earth 9
8 Status CVBS
Blue in 7
6 Audio in (L)
Blue earth 5
4 Audio earth
Audio out (L) 3
2 Audio in (R)
Audio out (R) 1
■
AV3 SCART terminal
(RGB, VIDEO, S-VIDEO, Q-Link)
AV3 - Pins 15 and 20 are dependent on AV3 S-VHS /
VIDEO switching.
Socket Earth 21
20 CVBS in (video)
CVBS out (video) 19
18 Earth
CVBS earth 17
16 Status RGB
Red in, S.C. - in 15
14 Earth
Red earth 13
12 --
Green in 11
10 Q-Link data
Green earth 9
8 Status CVBS
Blue in 7
6 Audio in (L)
Blue earth 5
4 Audio earth
Audio out (L) 3
2 Audio in (R)
Audio out (R) 1
Input signal that can be displayed
∗ Mark: Applicable input signal for Component (Y, P
Signal name Horizontal frequency (kHz)
525 (480) / 60i
525 (480) / 60p
625 (576) / 50i
625 (576) / 50p
750 (720) / 60p
750 (720) / 50p
1,125 (1,080) / 60i
1,125 (1,080) / 50i
•
Note • Signals other than above may not be displayed properly.
The above signals are reformatted for optimal viewing on your display.
28
■
AV2 SCART terminal
(VIDEO, S-VIDEO, Q-Link)
AV2 - Pins 15 and 20 are dependent on AV2 S-VHS /
VIDEO switching.
Socket Earth 21
20 CVBS in (video)
CVBS out (video) 19
18 Earth
CVBS earth 17
16 --
S.C. - in 15
14 Earth
Earth 13
12 --
-- 11
10 Q-Link data
Earth 9
8 Status CVBS
-- 7
6 Audio in (L)
Earth 5
4 Audio earth
Audio out (L) 3
2 Audio in (R)
Audio out (R) 1
■
HDMI terminal
Hot Plug Detect 19
18
DDC/CEC Ground 17
16
SCL 15
14
CEC 13
12
TMDS Clock Shield 11
10
TMDS Data0− 9
8
TMDS Data0+ 7
6
TMDS Data1 Shield 5
4
TMDS Data2− 3
2
TMDS Data2+ 1
, P ) and HDMI
B R
Vertical frequency (Hz) Component
15.73 59.94
31.47 59.94
15.63 50.00
31.25 50.00
45.00 60.00
37.50 50.00
33.75 60.00
28.13 50.00
FAQs
Before requesting service or assistance, please follow these simple guides to resolve the problem.
If problem still persists, please contact your local Panasonic dealer or Panasonic Customer Care Centre
for assistance.
White spots or
shadow images
(noise)
+5V Power
SDA
Reserved (in cable but N.C. on device)
•
TMDS Clock−
Check the position, direction,
TMDS Clock+
TMDS Data0 Shield and connection of the aerial.
TMDS Data1−
TMDS Data1+
TMDS Data2 Shield
logo appears
at the four corners
of the screen
Contrast is reduced
•
The function to prevent after-image
is activated.
(Not a faulty symptom)
● The screen saver is activated if
the TV unit is not operated for a
certain time in AV mode.
● Contrast is lowered when
teletext, radio, menu, etc. lasts
HDMI
for several minutes.
∗ ∗
● "after-image" (p. 5)
∗ ∗
∗ ∗
∗ ∗
Only one part
∗ ∗
∗ ∗ remains dark
∗ ∗
•
∗ ∗
A pixel or luminescent spot may
occasionally be missing in plasma
displays.
(Not a faulty symptom)
Pictures from an
equipment are unusual
when the equipment is
connected via HDMI
•
Is the HDMI cable connected properly?
• (p. 24)
Turn Off the TV unit and equipment,
• then turn them On again.
Check an input signal from the equipment.
• (p. 28)
Use an equipment compliant with
EIA/CEA-861/861B.
The remote control
does not work
•
Are the batteries installed correctly?
• (p. 6)
TV
Has the TV unit been switched On?
29