Panasonic Diga DMR-EX84C Operating Instructions Manual page 65

∫ Settings for DVB-C Channels/
Settings for DVB-T Channels
Press [OK] to show the following settings.
[DVB-C] DVB Manual Tuning
You can set channels manually that the DVB Auto Setup could not
complete successfully.
DVB Manual Tuning
Frequency 338,00 MHz
Symbol Rate Auto
Bandwidth 8
MHz
Signal Quality 0 10
0 10
Signal Strength
No. Channel Name Type New
Free TV : 0 Pay TV : 0 Radio : 0
START SCAN
0 9 Number
Frequency
SELECT RETURN
1 Press [2, 1] to adjust the frequency.
≥Adjust the frequency by checking the signal strength and signal
quality displays.
[Refer to "Signal Condition" (
signal strength.]
2 Press [3, 4] to select "Symbol Rate" and enter Symbol Rate for
tuning with the numbered buttons if needed.
≥Normally set to "Auto". (Default : "Auto")
3 Press [3, 4] to select "Bandwidth" and press [2, 1] to select
"7 MHz" or "8 MHz".
4 Press [OK] to start scan.
The set channel is displayed in the table.
5 Press [EXIT] and press [W X CH] to check that applicable
channels have been selected.
[DVB-T] DVB Manual Tuning
You can set channels manually that the DVB Auto Setup could not
complete successfully.
DVB Manual Tuning
Channel System
Western Europe (CCIR)
Frequency [CH24] 498,0 MHz
Signal Quality 0 10
Signal Strength 0 10
Channel Name Type New
No.
TV : 0 Radio : 0 Data : 0
START SCAN
OFFSET Change Channel System
CH RETURN
1 Press [3, 4] to select the channel you want to set.
2 Press [2, 1] to adjust the frequency.
≥Adjust the frequency by checking the signal strength and signal
quality displays.
[Refer to "Signal Condition" (
signal strength.]
3 Press [OK] to start scan.
The set channel is displayed in the table.
4 Press [EXIT] and press [W X CH] to check that applicable
channels have been selected.
Add New DVB Channels
You can search for newly added digital channels to receive.
[DVB-C]
Add New DVB Channels
Progress 0% 100%
No. Channel Name Type Quality
[DVB-C] Press [3, 4] to select "Quick Scan" or "Full Scan" and press
[OK].
The unit starts searching for newly available digital channels. This
takes about 20 minutes.
A message is displayed when the search is finished.
"No new DVB channels found." is displayed when no new channels
can be found.
Press [OK] to save the newly found channels.
New Channel Message
New Channel
A new DVB Channel has been found.
Start DVB Auto Setup ?
Selecting DVB Auto Setup will delete
all Timer Programmes.
Yes No
right) for signal quality and
If there is no signal quality and/
or signal strength, press the
"Red" button and select the
correct channel system.
right) for signal quality and
[DVB-T]
Add New DVB Channels
Scan CH 5 69
CH Channel Name Type Quality
[Automatic] When a new DVB channel is added, New Channel
Message appears automatically.
If you select "Yes" on the display, Auto-Setup starts
(all channel settings are deleted. The timer
recording programmes are also cancelled.).
[Off] New Channel Message does not appear.
Signal Condition
You can check the Signal Condition.
[DVB-C]
DVB Signal Condition
1 Das Erste
DVB Channel
Signal Quality 0 10
Signal Strength 0 10
Kabel Deutschland
Network Name
113 MHz, 6900kS/s
Parameter
Channel +
–
RETURN Channel
Press [W X CH] to select the channel.
When "Signal Condition" is displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [W X CH] to select a digital channel. "D" appears on the
unit's display.
3 Display the Setup menu again (
Signal Quality
The quality of the signal is shown.
Below 2 (display red):
The signal quality is so poor that there may be interference in the
pictures and sound.
2–5 (display orange):
The signal quality is basically adequate, but brief interference in the
pictures and sound is possible in isolated case.
Over 5 (display green):
Optimum picture and sound quality.
Signal Strength
The strength of the signal is shown.
The display for signal strength is grey. "0" means signal strength 0%,
"10" means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.
≥When the signal is weak:
– adjust the aerial reception with "DVB Manual Tuning" in the
Setup menu ( left).
– check that the current digital broadcast channel is correctly
broadcasting.
[DVB-C] Network Name
The network name which is stored in the transport stream list for the
current DVB service is displayed.
If there is no network name in it, "Unknown" is displayed.
[DVB-C] Parameter
The frequency and the symbol rate are displayed.
[DVB-C] DVB Advanced Setup
You can set up channels by entering "Home Frequency" and
"Network ID" obtained from your cable provider.
≥Digital timer recording programmes are cancelled and digital
tuning data are replaced by new ones.
DVB Advanced Setup
Home Frequency 338,00
MHz
Network ID 0
0 10
Signal Quality
Signal Strength 0 10
1 Press [2, 1] to select "Yes".
2 Press [3, 4] to select "Home Frequency" and press [2, 1] to
select the predefined value.
≥You can also enter the frequency with numbered buttons.
3 Press [3, 4] to select "Network ID" and enter Network ID with
numbered buttons.
4 Press [OPTION] to add "Symbol Rate", if needed.
≥If you do not need to add "Symbol Rate", go to step 6.
5 Press [3, 4] to select "---- ksym/s (User Def.)" and enter the
symbol rate with numbered buttons and then press [OK].
6 Press [OK].
Advanced Setup starts.
[DVB-T]
DVB Signal Condition DVB Signal Condition
DVB Channel
DVB Channel [CH14] 5 BR3 [CH14] 5 BR3
Signal Quality Signal Quality 0 0 10 10
Signal Strength Signal Strength 0 0 10 10
Channel Channel + +
– –
RETURN RETURN Channel Channel
64).
VQT3C69
65