Table of Contents
Advertisement
8-1. Gamma Correction (GAMMA)
1. Move the cursor to the GAMMA parameter. The "I"
cursor starts blinking.
2. While observing the waveform monitor or the colour
video monitor, adjust the gamma level.
When the "I" cursor is at the end of the "+" side,
gamma correction is set to OFF.
When the "I" cursor is at the end of the " " side,
black strech (BLACK STRET) is set.
8-2. Auto Knee ON/OFF (AUTO KNEE)
1. Move the cursor to the AUTO KNEE parameter.
2. Select ON or OFF for the auto knee mode.
8-3. Total Pedestal Level Control (TOTAL-PED)
1. Move the cursor to the TOTAL-PED parameter. The
"I" cursor starts blinking.
2. While observing the waveform monitor or the colour
video monitor, adjust the total pedestal level (black
level).
Move the "I" cursor to the "+" side to make the
image brighter.
Move the "I" cursor to the " " side to make the
image darker.
8-4. Chrominance Level Control (CHROMA GAIN)
1. Move the cursor to the CHROMA GAIN parameter.
The "I" cursor starts blinking.
2. While observing the waveform monitor or the colour
video monitor, adjust the chroma level.
8-5. Detail Band Control (DTL BAND)
1. Move the cursor to the DTL BAND parameter. The
"I" cursor starts blinking.
2. While observing the colour video monitor, adjust
the aperture level.
Move the "I" cursor to the "+" side to raise the fre-
quency.
Move the "I" cursor to the " " side to lower the fre-
quency.
8-6. Horizontal Detail Gain Control (HDTL GAIN)
1. Move the cursor to the HDTL GAIN parameter. The
"I" cursor starts blinking.
2. While observing the colour video monitor, adjust
the aperture level.
Move the "I" cursor to the "+" side to make the
image sharper.
Move the "I" cursor to the " " side to make the
image softer.
When the "I" cursor is at the end of the " " side, the
horizontal detail level is set to OFF.
8-7. Vertical Detail Gain Control (VDTL GAIN)
1. Move the cursor to the VDTL GAIN parameter. The
"I" cursor starts blinking.
2. While observing the colour video monitor, adjust
the aperture level.
Move the "I" cursor to the "+" side to make the
image sharper.
Move the "I" cursor to the " " side to make the
image softer.
When the "I" cursor is at the end of the " " side, the
vertical detail level is set to OFF.
8-8. Red Detail ON/OFF (RED DTL)
1. Move the cursor to the RED DTL parameter.
2. Select ON or OFF for the RED DTL mode.
When ON is selected, the red detail is enhanced.
8-9. Clear Digital Noise Reduction Control
(CLEAN DNR)
1. Move the cursor to the CLEAN DNR parameter.
2. Select OFF, LOW or HI for the CLEAN DNR mode.
8-10. 2 Dimension Low Pass Filter (2D LPF)
1. Move the cursor to the 2D LPF parameter.
2. Select ON or OFF for the 2D LPF mode.
8-11. 6 Chroma Matrix Controls
(MATRIX R-G)
(MATRIX R-B)
(MATRIX G-R)
(MATRIX G-B)
(MATRIX B-R)
(MATRIX B-G)
1. Move the cursor to the desired matrix item. The "I"
cursor starts blinking.
2. While observing the vectorscope or the colour
video monitor, adjust the matrix level.
Resetting to the factory settings
Any of the above settings except AUTO KNEE, RED
DTL, CLEAN DNR and 2D LPF, can be reset to the fac-
tory settings.
Move the cursor to the desired item and press A and
B simultaneously for a second or more.
-20-
Advertisement
Table of Contents
