Miele KM 406 Installation Instructions Manual
Hide thumbs
Also See for KM 406:
- Operating instructions manual (28 pages) ,
- Dimension manual (1 page) ,
- Technical information (66 pages)
Related Manuals for Miele KM 406
Summary of Contents for Miele KM 406
-
Page 1: Installation Instructions
Installation Instructions Gas Cooktop KM 404 KM 406 ® ® To prevent accidents and machine damage, read the operating instructions installation or use. M.-Nr. 05 060 881... - Page 2 ß ß ß ß ß...
- Page 3 KM 406........
- Page 4 = minimum safety distance KM 404 = 10" (250 mm) KM 406 = 10" (250 mm) Deep fryers must not be installed next to gas cooktops. Gas flames can ignite splattering oil. A distance of at least 12"...
- Page 5 However, under certain circumstances it may be possible for an installation in these applications. Please contact a Miele Dealer or Miele’s Technical Service Department with specific There must be a minimum safety requirements. distance of at least 30 inches (760 mm)
- Page 6 a Support bracket b Building in height plus " (3 mm) for fixing screw * Please allow an additional 3 " (90 mm) depth across the rear of the cooktop for clearance of the gas regulator and adapter (see "Gas connection"...
- Page 7 a Support bracket b Building in height plus " (3 mm) for fixing screw * Please allow an additional 3 " (90 mm) depth across the rear of the cooktop for clearance of the gas regulator and adapter (see "Gas connection"...
- Page 8 (562 mm) " (851 mm) (1138 mm) " (1426 mm) All Miele combisets have the same length and width. Make sure that there " (1714 mm) is enough room under the countertop to allow for the depth of the various "...
- Page 9 a Support brackets The illustration shows the layout for 3 combisets, their respective support b Support bars bars, b, and the support brackets, a, c Slight gap between support bar and required for their correct installation. countertop If more than 3 combisets are being d Bracket center line installed, add an additional 11 "...
- Page 10 ^ Place the brackets, a, as shown in ^ Arrange the bars, b, as shown in the the illustration. illustration. ^ Drill two ^ Drill " (1.5 mm) pilot holes for " (1.5 mm) pilot holes through each bracket and secure them using the brackets and secure them using the supplied screws.
- Page 11 Any pipe connections must be made ^ Screw the gas regulator/adapter using a thread sealant approved for combination onto the nipple at the gas connections. Failure to correctly rear of the cooktop. install these items could lead to a ^ Guide the power cord through the cut gas leak and subsequent explosion.
- Page 12 The cooktop must not be permanently sealed into the countertop when installed. If the cooktop is sealed into position, the countertop or appliance may be damaged if the cooktop needs to be removed for maintenance or service. The sealing strip under the edge of the cooktop provides a sufficient seal for the countertop.
- Page 13 This appliance must be electrically This appliance is equipped with a grounded according to local or three-prong grounding plug to national codes. prevent shock hazards. It should be All electrical work should be plugged directly into a properly performed by a qualified electrician grounded outlet.
- Page 14 Installation and service must be The gas connection must be made performed by a qualified installer, in accordance with local codes or, in service agency or the gas supplier. the absence of local codes, with In Massachusetts a licensed the National Fuel Gas Code, plumber/gasfitter is required.
- Page 15 Do not use any regulator or adapter adapter is necessary for your particular unless it has been supplied by Miele. Doing so may cause a gas installation, a customized one can be obtained free of charge from the Miele leak.
- Page 16 Maximum output 6000 1.75 Minimum output 1000 0.29 Maximum output 10000 2.93 Minimum output 1600 0.47 Maximum output 17500 5.13 Minimum output 0.18...
- Page 17 All cooktops come set for connection to either natural gas or LP gas. The ^ Unscrew the hexagonal silver cap adjustment of the included regulator located on the top of the regulator. corresponds with the gas type of the ^ Make sure that the spring stays in cooktop.
- Page 18 Turn off the main gas supply (if the appliance has been installed) and disconnect the appliance from the main electrical power supply before proceeding. The following orifices and needle valves should be installed into their respective burners. ^ Insert a screwdriver through the Front burner 1.15...
- Page 19 ^ Remove the pan support, the burner cap a, and the burner head b. ^ Using a 7mm nut driver or socket, unscrew the orifice c. ^ Install the new orifice and reassemble the above parts in the reverse order.
- Page 20 Turn off the main gas supply (if the appliance has been installed) and disconnect the appliance from the main electrical power supply before proceeding. ^ Using a T 20 Torx screwdriver, remove the 4 screws, a, holding the upper and lower housings together. ^ Securing the top level, carefully separate it from the lower housing.
- Page 21 The following orifices and needle valves should be installed into their respective burners. Large burner 2.00 0.88 Small burner No 34 0.40 Large ^ Use a 10 mm wrench to remove the burner 1.20 0.54 Small orifice. While doing this, use a 13 mm burner No 7 0.25...
- Page 22 ^ Using a small screwdriver, unscrew the needle valves and remove them with a pair of needle nose pliers. ^ Insert the new valves and screw them into place. a Needle valve with small orifice (0.25 for propane). b Needle valve with large orifice (0.54 for propane).
- Page 23 ^ First, loosen fitting, c, using an 8 mm wrench. Hold nut, b, with a 12 mm wrench while doing this to prevent the tubing from twisting. ^ Then remove fitting, b, from fitting, a, by using two 12 mm wrenches. ^ Remove the orifice, d, and replace it with the new orifice.
- Page 24 ^ After converting the cooktop to an alternative type of gas, affix the label supplied with the jet kit on to the data plate over the type of gas stated. ^ Check that there are no leaks. ^ Check that the burner is correctly assembled.
- Page 28 Alteration rights reserved / 0204 M.-Nr. 05 060 881 / 00 This paper is made from cellulose bleached without the use of chlorine.