Panasonic SC-PT160 Operating Instructions Manual page 36

Troubleshooting guide (continued)
7 Picture abnormal or unviewable
The picture on the television is
not displayed correctly or
disappears.
Picture stops
Picture size does not fi t the screen. • Change "TV ASPECT" in the "VIDEO" tab.
Menu is not displayed correctly.
Auto zoom function does not work
well.
When playing PAL disc, picture is
*
3
distorted.
7 Progressive video
Pictures not in progressive output. • Select "PROGRESSIVE" in "VIDEO OUT (I/P)" in the "VIDEO" tab.
7 Unit displays
The display is dark.
"NO PLAY"
"NO DISC"
"OVER CURRENT ERROR"
"F61"
"F76"
"DVD U11"
"ERROR"
"DVD H & &"
"DVD F & & &"
& stands for a number.
"REMOTE 1" or "REMOTE 2"
1
For Southeast Asia and Thailand
2
For the Middle East, South Africa, Saudi Arabia, Kuwait and Continental Europe
* 3
For Southeast Asia, Thailand, the Middle East, South Africa, Saudi Arabia and Kuwait
36
RQT8043
• The unit and television are using different video systems.
* 1 Use a multi-system or NTSC television.
* 2 Use a multi-system or PAL television.
• The system used on the disc does not match your television.
– PAL discs cannot be correctly viewed on an NTSC television.
– This unit can convert NTSC signals to PAL 60 for viewing on a PAL television
("NTSC DISC OUT" in "VIDEO" tab).
• Ensure that the unit is connected directly to the television, and is not connected
through a video cassette recorder.
• Mobile telephone chargers can cause some disturbance.
• If you are using an indoor television antenna, change to an outdoor antenna.
• The television antenna wire is too close to the unit. Move it away from the unit.
• Change "SOURCE SELECT" in Functions menu.
• Picture may stop if the DivX fi les are greater than 2 GB.
• Use the television to change the aspect.
• Change the zoom setting. ("ZOOM" in Functions menu.)
• Restore the zoom ratio to "NORMAL". ("ZOOM" in Functions menu.)
• Turn off television zoom function.
• Zoom function may not work well, especially in dark scenes and may not work
depending on the type of disc.
• Set "TRANSFER MODE" in Functions menu to "AUTO".
* 3
• The unit's VIDEO OUT terminal outputs the interlaced signal even if "PRG" is
displayed.
• Select "BRIGHT" in "FL DIMMER" in the "OTHERS" tab.
• You inserted a disc the unit cannot play; insert one it can.
• You inserted a blank disc.
• You inserted a disc that has not been fi nalized.
• You have not inserted a disc; insert one.
• You have not inserted the disc correctly; insert it correctly.
• The USB device is drawing too much power. Switch to DVD/CD mode, remove
the USB and turn the unit off.
• Check and correct the speaker cable connections.
If this does not fi x the problem, consult the dealer.
• There is a power supply problem. Consult the dealer.
• Disc may be dirty. Wipe it clean.
• Incorrect operation performed. Read the instructions and try again.
• Trouble may have occurred. The numbers following "H" and "F" depend on the
status of the unit. Turn the unit off and then back on. Alternatively, turn the unit
off, disconnect the AC mains lead, and then reconnect it.
• If the service numbers fail to clear, note the service number and contact a
qualifi ed service person.
• Match the modes on the main unit and remote control. Depending on the number
being displayed ("1" or "2"), press and hold [ENTER] and the corresponding
numbered button ([1] or [2]) for at least 2 seconds.
Page
—
—
24
32
—
—
—
22
—
24
—
22
22
—
—
22
24
11
25
14
—
—
—
16
—
10
—
27
—
—
—
34