Table of Contents
Advertisement
ConTour Series 1.0
Components:
Stud starter cable:
Steel-wire cable with a length of 270 mm,
including a stud and snap link for fastening the
speaker enclosure to the pick point on the stage
ceiling.
HK Audio
®
item number: 193 543
Arrest wire
Additional securing cable for flown CT 112/ CT 115
speakers; 4 mm in diameter, 100 cm in length,
including snap links
HK Audio
®
item number: 193643
EB 10 eyebolt
HK Audio
®
item number: 193673
2.4 Mounting
Attach the speaker enclosure to a pick point on
the Aeroquip track using a starter cable
comprising a snap link, a cable with the required
length, and a stud. One track is located on the
top of the housing for arraying the enclosure
vertically, and one is on the side for arraying the
enclosure horizontally.
Secure the speaker to prevent it from falling. To
this end, insert an HK AUDIO
the recessed thread on the rear of the CT 112 or
CT 115. Attach the arrest wire to the eyebolt and
transom.
Ensure the pick points are able to handle the
given load (a CT 112 with a starter cable weighs
approx. 27 kg; a CT 115 with a starter cable weighs
approx. 37 kg).
The position of the stud in the Aeroquip track
determines the cabinet's angle of tilt. Since the
length of the cables used to attach the cabinets to
the rigging point (the ceiling of the venue, a
transom, a cross beam, etc.) will vary according
to the given venue's mounting options, you must
adjust the length of the cables accordingly. If the
®
length of the HK AUDIO
starter cable does not
suffice, you can have cables made in the required
length by any certified cable manufacturer using
the following parts.
Snap link: Snap link with safety lock gate, 1 ton
load-carrying capacity, quality grade 8 (for
example: SOCS 6-8)
Stud: Aeroquip 5013 Series L Double Stud Fitting
(ISO 9788)
HK Audio
®
item number: 193195
Cable: Galvanized steel-wire cable, DIN 3060, Ø 6
mm, 1770 N/mm 2, sZ 6 x 19 + FE, calculated
breaking strength: 22.8 kN; minimum breaking
strength: 19.6 kN
2.5 Maximum Number of Flown CT 112/ CT 115
Enclosures
Mount no more than one CT 112 or CT 115
enclosure using this system. This applies to the
speaker in both vertical and horizontal array.
Caution: Flying more than one CT 112 / 115
cabinet in stacked array voids the operating
license!
2.6 Structural Modifications of ConTour Series™
Rigging Hardware
No structural modifications may be made without
the manufacturer's consent. This also applies to
welding work performed on supporting parts.
Structural alterations require the manufacturer's
written approval. Use original replacement and
wearing parts only.
2.7 Original HK AUDIO
Use original HK AUDIO
standards authority TÜV has not certified any
other parts for use! Always install parts in
accordance with these installation instructions!
Store all documents pertaining to the system in a
safe place!
2.8 Initiation and Operation
®
EB 10 eyebolt into
§ 39, VBG 9a of the German employers' liability
insurance association's accident prevention
regulations requires that load-carrying equipment
be inspected by a qualified expert and possible
defects be eliminated prior to initial commissio-
ning by the recipient.
§ 41 VBG 9a requires that load-carrying equip-
ment be subjected to a non-routine inspection
following damage, repair work and other
incidents that can affect load-carrying capacity.
®
Accessories:
®
parts only! The safety
Advertisement
Table of Contents
