Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
CADET 1.6 GPF TWO-PIECE PRESSURE-
ASSISTED TOILETS
- Model 2333 Elongated
- Model 2366 Round Front
- Model 2377 Elongated - 16-1/2" High Bowl
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE: For proper operation these products require a minimum of 20 psi line pressure
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
FINISHED WALL
31 (787mm)
REF.
29 (737mm)
REF.
305mm
(12)
DIMENSIONS (Nominal)
closet flange centerline (rough-in) must be 12" (305 mm)
minimum.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 4
Adjustable Wrench
Flexible Supply Tube
19-1/2
(495mm)
SUPPLY
AS
REQ'D
*
203mm
(8)
FINISHED
FLOOR
NOTE: Distance from wall to
Sealant
Closet Bolts
3
CLOSET FLANGE
29
(737mm)
OR
CLOSET BOLTS
31-1/2
(800mm)
ADA HEIGHT
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 ,
and slide into place 6" (152 mm) apart and
parallel to wall.
Tape Measure
Carpenters Level
305mm
(12)
Saniwares
730 4 7 9 -100 R ev. A
Advertisement
Related Manuals for American Standard Cadet 1.6 GPF Two-Piece Pressure Assisted Toilets 2366
Summary of Contents for American Standard Cadet 1.6 GPF Two-Piece Pressure Assisted Toilets 2366
-
Page 1: Installation Instructions
- Model 2377 Elongated - 16-1/2" High Bowl Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. - Page 2 WAX RING SEALANT INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around base flange. BOLT CAP CLOSET BOLT WASHER INSTALL TOILET...
-
Page 3: Care And Cleaning
TANK WATER INLET WASHER FLEXIBLE COUPLING NUT SUPPLY VALVE NUT COMPRESSION COLLAR TRIM PLATE VALVE CAUTION: Overtightening of COUPLING NUT could result in breakage and potential flooding. CONNECT WATER SUPPLY Connect water supply line between shutoff valve and tank water inlet fitting. -
Page 4: Troubleshooting Guide
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address: In the United States: American Standard Inc., P.O. Box 8305 Trenton, New Jersey 08650...