Frigidaire GLEB27Z7HBC Installation Instructions Manual

Frigidaire GLEB27Z7HBC Installation Instructions Manual

Electric wall oven
Hide thumbs Also See for GLEB27Z7HBC:

Advertisement

Available languages

Available languages

iNSTALLATiON
AND SERVICE MUST BE PERFORMED BY A QUALiFiED
iNSTALLER.
iMPORTANT:
SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.
READ AND SAVE THESE iNSTRUCTiONS
FOR FUTURE REFERENCE.
FOR YOUR SAFETY: Do not store or use gasoJine or other flammabJe vapors and Jiquids in
the vicinity
of this or any other appliance.
Your
new
wall
oven
has
been
designed
to fit
a limited
variety
of cutout
sizes
to make
the
job
of installing
easier.
The
first
step
of your
installation
should
be to measure
your
current
cutout
dimensions
and
compare
them
to the
cutout
dimensions
chart
beJow
for
your
model
You
may
find
httle
or no cabinet
work
will
be necessary.
Do not remove
spacers
(if equipped)
on the side wails
and/or
on the back of the built-in
oven.
These
spacers
center
the oven
in the
space
provided.
The oven
must
be centered
to prevent
excess
heat
buildup
that
may
resuJt in heat
damage
or fire.
[
Cutout openings--_-]
I
I
,_Do
not install tt_e oven
closer than the
dimension
"K"
(see
table) to any adjoining
cabinetry
or
walls on tile door hinge side. This will
interfere
with
oven rack removal.
Figure
2
* Suggested distance from floor is 31" (78.7 cm)
Minimum required distance is 4 1/2" (11.4 cm)
for self-dean
models.
Minimum required distance is 10" (25.4 cm)
for easy-clean
models
1 1/2"
i Door
::Open
28 3132"
NOTE:
- Self-clean
Models:
Allow at least 27 X" (69.2 cm)
clearance for door depth when it is open.
- Easy-dean
Models:
Allow at least 26 X" (66.7 cm)
clearance for door depth when it is open.
NOTE: For a cutout height greater titan 29" (73.6 cm) add
one 2" (5 cm) wide wood spacer to each side of the opening
under tt_e appliance side rails.
(3.8 cm)
Min.
H
31 "*
(78.7
27" Min.
cm}
Electrical Junction box
location and Hole for
space 2"(5.1 cm)
left wall for Self-
Clean Models.
Electrical junction box
and Hole for Cable
space 2" (5.1 cm}
from right
wall for
Easy Clean Models.
cm)
Max.
Electrical junction box
(right or left side
depending of model)
2" (B cm} Wide Wood
Spacer if Needed
NOTE: Basemust be capable of supporting 150 pounds (68 Kg).
Figure
1
27" (68.6 cm) Easy Clears
26 7/8 (68.2)
27" (68.6 cm) Self Clean
26 7/8 (68.2)
25 5/32 (63.9}
25 1/4(64.1)
27" (68.6 cm) Easy Clears
24 7/8 (63.2)
27" (68.6 cm) Self Clean
24 7/8 (63.2)
All dimensions are in inches (cm).
Some models are not available in Canada.
Printed in United States
30 9116 (77.6)
24 11/I 6 (62.7)
24 1/4 (61.6)
31 1/8 (79.1)
24 11/I 6 (62.7)
25 3/8 (64.5)
231/2(59.7)
281/8(71.4)
295/8(75.2)
3(7.6)
231/2(59.7)
281/8(71.4)
301/8(76.5)
41/2(11.4)
PIN 318201508
(0410)
Rev.
English - pages 1-9
EspaF_ol- paginas 10-18
Fran_ais - pages 19-27

Advertisement

Table of Contents
loading

Summary of Contents for Frigidaire GLEB27Z7HBC

  • Page 1 iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. FOR YOUR SAFETY: Do not store or use gasoJine or other flammabJe vapors and Jiquids in the vicinity of this or any other appliance.
  • Page 2: Important Instructions

    grounded branch circuit, protected by a circuit breaker or Important Notes to the Installer fuse, having amperage as noted on the rating plate (the Read all instructions contained in these installation rating plate is located on the oven frame). instructions before installing the wall oven. Remove packing material...
  • Page 3: Electrical Connection

    4. Electrical connection Wait at least three (3) hours after receiving t hisbuilt-inovenbefore switching thepoweron It is the responsibility and obligation of the consumer to to preventpossible damage to the built-inovencontrol contact a qualified installer to assure that the electrical at power on.
  • Page 4 If used in mobile homes or if local codes 5. Preparing the Wall Oven NOT permit connection of the frame grounding Easy dean Models conductor to the neutral (white) wire, separate This wall oven can easily be modified to a left or a the white and bare copper ground wires that extend right hand door opening.
  • Page 5 I0. Reassemble the handle andfiller plates #2, #3 and Tools required: No.2 Phillips@ and No.2 Robertson @ #12ontheopposite sideof thedoor. screw drivers, 1/2" open key, small flat-blade screw 11.Remove andrelocatethe filler plates#7 on the driver, long nose pliers. opposite sideof theoven frame. 12.Remove the latch pin#10 andrelocatelatchon Procedure for Door Reversal...
  • Page 6 8. Turnthe outerdoorassembly a half turn (180 °) 18. Move the oven light switch to the left side of the and replacethe outer door assembly over the frame: over lower door assembly. R eplacethe nylon slide Grab the switch plunger and gently pull out from its underthe handle(thinsidefacinginward)onthe location.
  • Page 7: Cabinet Installation

    5. Cabinet Installation B. Self Clean Models A. Easy Clean Models Insert the appliance into the cutout. Screws are Remove and lay aside the lower vent trim which is provided for fastening the appliance front frame to the taped to the oven outer side panel. cabinet.
  • Page 8 Side filler panels are necessary to Only certain cooktop models m ay beinstalled isolate the unit from adjoining over c ertain built-in electric o ven models, listed by cabinets. Panel height should theMFG IDnumber ( see theinsert s heet i ncluded allow for installation of approved intheliterature p ackage).
  • Page 9: Checking Operation

    120V/60Hz Flexible ApF Grounded Flare Outlet Right Side Union of Cabinet Pressure Regulator (To be Cabinet sides or J_-------v accessible filler panel for shut-off Manual Wall Oven Shutoff valve Valve Cabinet operation) Figure 13 - SELF CLEAN MODELS ONLY TYPICAL UNDER COUNTER INSTALLATION OF AN ELECTRIC BUILT-IN OVEN WITH A GAS COOKTOP MOUNTED ABOVE IMPORTANT NOTE: A fan inside the upper rear part...
  • Page 10 LA INSTALACI6N Y EL SERVICIO DEBE DE HACERLOS UN INSTALADOR CAUFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR ELECTRICO LOCAL. LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS. PARA SU SEGURJDAD: No alrnacene ni utiJke gasoJJna u otros vapores y Jiquidos inflamabJes en Ja proximidad de este o de cualquier...
  • Page 11 Cumpla con todos los c6digos en vigor y todos los re- Notas importantes para el Mstalador glamentos locales. Lea todas las instrucciones contenidas en este manual 1. Para el suministro electrico solamente se necesita corrien- antes de instalar el horno. te con frecuencia de 60 Hz AC y fase unica de 120/208 o Saque...
  • Page 12 Cuando utilice su horno empotrado por la 4. ConexiOn el ctrica primera vez, espere por Io menos tres (3) horas antes El usuario tiene la responsabilidad personal y obligaci6n conectarlo al suministro el#ctrico. Los controles electricos de utilizar un instalador calificado, para asegurar que la...
  • Page 13 Si este horno va a usar en una casa sobre 5. Preparaci6n del homo a pared ruedas o si los c6digos locales NO permiten Modelos f&cilmente limpiables el armazon este conectado al neutro (blanco) Este horno de pared puede modificarse facilemente la toma a tierra,...
  • Page 14 Deslize y ajuste el panel de vidrio a la esquina 3 tornillos Buje de la Soporte de la (encima de la bisagra bisagre de la tornillos la puerta interna de acero esmaltada (hacia El perno pue_ta) (2 lugares) puerta nueva ubicacion del tirador).
  • Page 15 enroscado par° velvet a montar luego. Tornille de amertizador de golpes de _ ._ Tornille de bisagra la puerta _ • _ , L. la parte superior de la 15. Mueva los 3 tornillos de bisagra postizos del lade DuJe ue _aulsagra _#_'_._ puerta derecho...
  • Page 16 5. Instalaci6n del Gabinete B. Modelos auto IJmpiables A. Modelos f_dlmente limpiables Introduzca el artefacto en el recortado. Lostornillos Retire y ponga lado rejilla baja est_qn provistos para fijar el armazon frontal ventilaci6n que est,1 pegada a la parte exterior artefacto al gabinete.
  • Page 17 Paneles Ilenadores laterales son Se puede instalar solamente ciertos modelos necesarios para aislar el homo de de estufas por encima de ciertos hornos a los gabinetes adyacentes. La altura pared electricos, listados seg0n el n0mero de los paneles debe dejar espacio del MFG ID (consulte la hoja incluida en el suficiente...
  • Page 18: Nota Importante

    4" (10.2 cm) Lado derecho gabinete (para tener acceso a la wilvula Gabinete del cierre homo a pared manual) Figura 13- MODELOS AUTO LIMPIABLES SOLAMENTE INSTALACION TJPICA PARA UNA ESTUFA DE GAS ENCIMA DE UN HORNO DE PARED INSTALADO DEBAJO DEL MOSTRADOR 6.
  • Page 19 L'INSTALLATION ET L'ENTRETiEN DOIVENT f:TRE EFFECTUES PAR UN INSTALLATEUR QUALIFIE. iMPORTANT" CONSERVEZ POUR L'INSPECTEUR D'ELECTRICITE LOCAL. LISEZ ET CONSERVEZ CES iNSTRUCTiONS POUR RI_FI_RENCES ULTI_RIEURES. POUR VOTRE SECURITE : N'entreposez pas ou n'utilisez pas d'essence ou d'autres produits inflammables _ proximit6 de cet appareil ou de tout autre appareil 61ectrom_nager.
  • Page 20 Installateur Observez tousles r_glements et les codes Iocaux applicables. 1. Lisez toutes ces instructions avant de proceder Un cable electrique a 3 ou 4 fils de 120/240 ou 120/208 I'installation de votre appareil. Volt monophase, 60 Hz CA est requis sur un circuit 2.
  • Page 21 IIfaut attendre au moins trois (3)heures 4. Connexions lectriques apres sareception avant d emettreI'appareil sous tension Le consommateur est responsable et doit communiquer poureviter t outepossibilite d'endommager lacommande du fourlotsdelaraise sous tension. avec installateur qualifie pour s'assurer I'installation electrique est adequate et conforme avec le National...
  • Page 22 Si I'appareil est utilis_ dans une maison mobile, 5. Preparation du four encastr ou si les codes Iocaux N'AUTORISENT PAS une ModUles faciles a nettoyer connexion du conducteur de raise a la terre Ce four encastre peut facilement _tre modifie pour chassis au neutre...
  • Page 23 Reassemblez moulures tout Pour inverser I'ouverture de la porte, vous devez inversant leurs positions (la moulure #5 en bas et embaucher un technicien d'experience afin de prevenir la #6 en haut). tout dommage pieces problemes 10. Reassemblez la poignee et les obturateurs #2, #3 d'alignement de la porte.
  • Page 24 Retournez la porte, le panneau exterieur face a la table 18. Deplacez I'interrupteur de la lampe du four vers le c6te de travail. Inversezla position de la cheville du Ioquet gauche du cadre avant: avec le bouton de la cheville du Ioquet du c6te oppose Tirez doucement le poussoir de I'interrupteur pour...
  • Page 25: Installation

    5. installation dans I"arrnoire A, ModUles fadJe a nettoyer B. ModUles autonettoyants Retirez la moulure inferieure qui est attachee Ins_rez I'appareil dans le d_coupage. Des vis sont le c6te du four a I'aide de rubans adhesifs. fournies pour fixer le chassis avant de I'appareil Glissez...
  • Page 26 Des panneaux lateraux sont Seul certains modeles de plaque de cuisson necessaires pour isoler I'unite peuvent _tre superposes sur certains modeles de armoires adjacentes. La hauteur four electriques encastres, enumeres par numero des panneaux doit permettre d'identification du fabricant (voir la feuille installation des modeles de plaque annexee dans I'enveloppe...
  • Page 27 Prise de Tuyau flexible d'appareil 120V/60Hz Raccord raise a la C6te droit de conique terre I'armoire Regulateur de pression (Doit 6tre Panneaux lat6raux _1_ accessible d'armoire Robinet pour Armoire de manuel permettre I'utilisation du four encastre robinet manuel) Figure 13 - MODELES AUTONETTOYANTS SEULEMENT INSTALLATION TYPE D'UNE PLAQUE DE CUISSON A GAZ AU DESSUS D'UN FOUR ENCASTRE SOUS UN COMPTOIR V_rification...

Table of Contents