Remote Control Operation; How To Use Antenna; Tv Operation; Programming By Remote - Haier HLT71 User Manual

Remote control operation

MUTE
1
PICTURE
2
3
MENU
4
5
6
1
4
7
7
8
9
Note:
a) Point the remote control unit from no more than about
5m from the remote control sensor and within about
°
60 of the front of the TV monitor.
b) Do not press the button too quick. Press the button
after the previous operation is completed.
1. MUTE: Used to toggle between normal & muted audio.
2. PICTURE: Press this button to select the picture display
effect between Dynamic, soft, personal or standard.
3. MTS: P ress to select the audio output language during
DTV mode if there are multi languages available, during
ATV mode, press this button to select audio output like
mono & stereo.
4. MENU: Press this button to access the menu interface.
5. SLEEP: Use to auto power off by setting sleep timer.
6. NAVIGATION buttons: Press to select the options under
OSD setting interface or alter the settings in a menu.
7. (0~9 ): Enter numeric values and to select the channel or
program directly by entering its number.
8. : Press to go to previously selected channel.
9. VOL-: Press this button to decrease the speaker volume.
10.POWER: Press this button to set the player to standby
on or off state( If the main power of the set is on).
11. ZOOM: Used to select the desired display mode wide or
normal. .
12. EXIT: Exit the menu interface.
13. EPG: Press this button to skim over TV programs guide.
14. OK/ENTER: Confirm the selection.
15. TV/AV: Select the desired signal input mode.
16. INFO: Press this button to display current program
information.
17. CH+: Press this button to increase the channel number.
18. CH-: Press this button to decrease the channel number.
19. - : Used to directly input TV channels.
20. VOLUME +: Press this button to increase the speaker
volume.
POWER
10
ZOOM
MTS
11
SLEEP EPG EXIT
12
13
ENTER
14
TV/AV
15
2 3
INFO
16
5 6
CH+
17
8 9
CH-
18
0
19
+
20
VOLUME

HOW TO USE ANTENNA

Directly connect external movable antenna to RF in, may
also connect roof antenna directly.
For better reception:
Adjust the direction/position of the antenna. The signal
strength depends on the area of reception. If the signal is
too weak, poor or no reception is possible. This is not a
malfunction.
ATTENTION:
Do not rotate the antenna in counter direction after fixing, it
may get loose & effect the channel reception.

TV OPERATION

GET STARTED
—
Be sure the TV antenna is connected to the set properly.
—
Plug the AC adaptor to the power source to power on
the TV set.
—
Slide power on/off switch to on position.
—
Press the TV/AV button on the remote or MODE button
on the main unit to select TV Mode.
—
Press AUTO/OK on the unit. Then select YES & press
AUTO button to program the channels onto the memory.
PROGRAMING BY REMOTE:
Press the MENU button on the remote, and then select the
satellite image by using the
button ( ) to select antenna function. Change to Air or
Cable by using button, depending upon the type of
connection. Then scroll to Auto Scan and press
twice, TV will start auto programing function taking all the
available channels into memory.
NOTE: Auto Scan function has to be done for TV to capture
channels initially.
PROGRAMING FROM UNIT
Turn the TV on and press menu button, scroll to satelite
image by pressing Vol + (
to select antenna function. Press Vol + to choose Air or
cable reception. Then press CH - (
function and press Vol + (
using CH - ( ) and press Vol + (
program.
SEARCH A PROGRAM
—
Press CH UP/DOWN button once, the channel number
changes. A desired channel can be reached using these
two keys.
—
NUMERIC button on the remote can facilitate you to
select a specific channel. If the channel number exceeds
10, input first digital unit, then another digital unit;
3
key. Then press down arrow
button
), and then press channel - (
) to select Auto scan
) and choose start scan by
). The unit will start
)