1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. A50-ASMBN02
  6. User manual

Toshiba A50-ASMBN02 User Manual

User manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

User's Manual
TECRA A50-A/W50-A
Satellite Pro A50-A

Advertisement

Table of Contents
loading

Related Manuals for Toshiba A50-ASMBN02

Summary of Contents for Toshiba A50-ASMBN02

  • Page 1 User's Manual TECRA A50-A/W50-A Satellite Pro A50-A...

  • Page 2: Table Of Contents

    The Keyboard ..................4-1 Using the AccuPoint ................4-4 Using the Fingerprint Sensor ............... 4-5 Optical disc drives ................4-11 TOSHIBA VIDEO PLAYER ..............4-19 TOSHIBA Blu-ray Disc Player ............4-21 Battery ....................4-23 Wireless WAN Device ................. 4-30 User's Manual...
  • Page 3 Memory media ..................4-44 ExpressCard ..................4-47 Smart Card ................... 4-48 External Display .................. 4-49 TOSHIBA Hi-Speed Port Replicator III 180W/120W ......4-53 Multi Monitor Support ................. 4-55 Serial Device ..................4-55 Security lock ..................4-56 Optional TOSHIBA Accessories ............4-56 Sound System and Video mode ............

  • Page 4: Chapter 1 Toshiba Legal, Regulatory And Safety

    TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2013 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

  • Page 5: Regulatory Information

    ® The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
  • Page 6 Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s External RGB monitor port, Universal Serial Bus (USB...

  • Page 7: Eu Declaration Of Conformity

    EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected/implemented those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards.
  • Page 8 Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA. The consequences of the use of this product in non-approved working environments may be: Interference with other devices or machines in the near surrounding area.
  • Page 9 For more detailed information about the collection and recycling programmes available in your country, please visit our website (http://eu.computers.toshiba-europe.com) or contact your local city office or the shop where you purchased the product. Disposal of batteries and/or accumulators...
  • Page 10 The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. TOSHIBA will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation.

  • Page 11: Video Standard Notice

    Video Standard Notice THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS ("VIDEO") AND/OR (II) DECODING AVC, VC-1 AND MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH...
  • Page 12 Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)"...

  • Page 13: Freetype License Issues

    This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
  • Page 14 Copyright 1996-2002, 2006 by David Turner, Robert Wilhelm, and Werner Lemberg Introduction ============ The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all files found in such packages, and which do not fall under their own explicit license.
  • Page 15 authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project', be they named as alpha, beta or final release. `You' refers to the licensee, or person using the project, where `using' is a generic term including compiling the project's source code as well as linking it to form a `program' or `executable'.
  • Page 16 -------------- Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission. We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising materials: `FreeType Project', `FreeType Engine', `FreeType library', or `FreeType Distribution'.

  • Page 17: Energy Star Program

    ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency. Your computer...

  • Page 18: Optical Disc Drive Safety Instructions

    To prevent direct exposure to the laser beam, do not try to open the enclosure. Location of the Required Label (Sample shown below. Location of the label and manufacturing information may vary.) TOSHIBA SAMSUNG STORAGE TECHNOLOGY KOREA CORPORATION 14F, Bldg. No.102, Digital empire2, 486 Sin-dong, Yeongtong-gu, Suwon-si,...

  • Page 19: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 20: Cleaning The Computer

    Stress injury Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture and lighting that can help reduce physical stress.

  • Page 21: Moving The Computer

    Moving the computer While the computer is designed for flexible day-to-day usage you should exercise a few simple precautions when moving it in order to help ensure trouble-free operation. Make sure all disk/disc activity has ended before moving the computer. Turn off (shut down) the computer.

  • Page 22: Safety Icons

    Safety Icons Safety icons are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions. A caution informs you that improper use of equipment or failure to follow instructions may cause data loss, equipment damage, or may result in minor or moderate injury.

  • Page 23: Chapter 2 Getting Started

    Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.

  • Page 24: Using Your Computer For The First Time

    Right-click Click the right Touch Pad control button once. Right click the mouse once. Press and hold on the touch screen (only for touch screen models). Double-click Tap the Touch Pad or click the left Touch Pad control button twice. Left click the mouse twice.
  • Page 25 DC power and reduces the voltage supplied to this computer. Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury.
  • Page 26 Connect the power cord to the AC adaptor. Figure 2-1 Connecting the power cord to the AC adaptor Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on your computer.
  • Page 27 Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.

  • Page 28: Turning Off The Power

    Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Power Condition Descriptions section for more information. After you turn on the power for the first time, do not turn it off until you have set up the operating system.

  • Page 29: Restarting The Computer

    Shut Down Mode When you turn off the power in Shut Down Mode, no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on. If you have entered data, either save it to the HDD/SSD or to other storage media.
  • Page 30 Please note that keyboard keys can only be used if the Wake- up on Keyboard option is enabled within the TOSHIBA HWSetup utility. If the computer enters Sleep Mode while a network application is active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.

  • Page 31: Hibernation Mode

    Executing Sleep Mode You can enter Sleep Mode in one of three ways: Click Start. Point to the arrow ( ) beside the Shut down button and then select Sleep from the menu. Close the display panel. Please note that this feature must be enabled within the Power Options.
  • Page 32 Saves data to the HDD/SSD when the computer automatically shuts down because of a low battery condition. You can return to your previous working environment immediately when you turn on the computer. Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature.

  • Page 33: Chapter 3 The Grand Tour

    Chapter 3 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section.
  • Page 34 Memory media slot This slot lets you insert an SD™/SDHC™/ SDXC™ memory card, miniSD™/microSD™ Card and MultiMediaCard™. Refer to the Memory media section for more information. Keep foreign metal objects, such as screws, staples and paper clips, out of the Memory media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

  • Page 35: Left Side

    Left side The following figures show the left side of the computer. Figure 3-2 The left side of the computer 1. Cooling vents 5. Universal Serial Bus (USB 3.0) ports 2. DisplayPort* 6. Headphone/Microphone jack 3. External RGB monitor port 7.

  • Page 36: Right Side

    Universal Serial Bus Two Universal Serial Bus ports, which comply to (USB 3.0) port the USB 3.0 standard, are provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices.
  • Page 37 Figure 3-3 The right side of the computer 1. ExpressCard slot or PC Card slot* 5. LAN jack 2. Optical disc drive* 6. DC IN 19V jack 3. Universal Serial Bus (USB 2.0) port* 7. Security lock slot 4. Serial Connector* 8.

  • Page 38: Back

    LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Operating Basics, for details.

  • Page 39: Underside

    Battery section. Docking port This port enables connection of an optional TOSHIBA Hi-Speed Port Replicator III 180W/ 120W described in TOSHIBA Hi-Speed Port Replicator III 180W/120W. Some models are equipped with a Docking port.

  • Page 40: Front With The Display Open

    Only the TOSHIBA Hi-Speed Port Replicator III 180W is applicable with this Docking port for TECRA W50-A series. Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is applicable with this Docking port for TECRA A50-A/Satellite PRO A50- A series.
  • Page 41 Figure 3-6 The front of the computer with the display panel open 1. Wireless communication antennas 9. Touch Pad control buttons (not shown)* 2. Microphone* 10. Power button 3. Web Camera LED* 11. Keyboard 4. Web Camera* 12. Touch Pad 5.
  • Page 42 Microphone The built-in microphone allows you to import and record sounds for your application - please refer to the Sound System and Video mode section for more information. Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your...
  • Page 43 Double tap this indicator to launch the TOSHIBA eco Utility. Touch Pad control The two buttons below the Touch Pad are used buttons like the buttons on a standard mouse - press the left button to select a menu item or to manipulate...

  • Page 44: Internal Hardware Components

    TOSHIBA PC Health Monitor utility by clicking Start -> All Programs - > TOSHIBA -> Support & Recovery -> PC Health Monitor, and then click PC Information. Please note that part of the hard disk's overall capacity is reserved as administration space.
  • Page 45 Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors. Legal Footnote (HDD/SSD Capacity) For more information regarding HDD/SSD Capacity, please refer to the Legal Footnotes section. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar.
  • Page 46 sustained battery life. Switching is automatic and does not require the user to reboot the computer. In the Manage 3D Settings menu of NVIDIA Control Panel, you can change the global 3D settings and create overrides for specific programs. The overrides will be used automatically each time the specified programs are launched.
  • Page 47 You can use BIOS Setup to enable/disable the function and change the specified time setting from Sleep Mode to Hibernation Mode. Launch the BIOS setup utility. Please refer to TOSHIBA Setup Utility section for further information. Select Advanced. Enable/Disable Intel(R) Rapid Start Technology function.

  • Page 48: Power Condition Descriptions

    ® When Intel Rapid Start Technology is enabled, Wake-up on LAN, Wake-up on USB or Wake-up from Sleep Mode automatically functions are not available when the computer has been switched from Sleep Mode to Hibernation Mode. The Windows cannot be restored normally if the battery is exhausted when the computer is moving from Sleep Mode to Hibernation Mode.
  • Page 49 Power on Power off (no operation) AC adaptor Remaining • Operates battery capacity • LED: off connected is above low battery trigger point Remaining • Operates battery capacity • LED: flashes is below low orange battery trigger point Remaining Computer shuts battery capacity down is exhausted...

  • Page 50: Power Indicator

    Power indicator Check the Power indicator to determine the power status of the computer - the following indicator conditions should be noted: Green Indicates power is being supplied to the computer and the computer is turned on. Flashing Orange Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition.

  • Page 51: Chapter 4 Operating Basics

    Chapter 4 Operating Basics This chapter describes the basic operations of your computer, and highlights the precautions that should be taken when using it. Using the Touch Pad The Touch Pad located in the palm rest may support the following gestures: Simply tap your finger on the Touch Pad to act on items on the screen.
  • Page 52 Keyboard indicator The following figure shows the position of the CAPS LOCK indicator and NUM LOCK indicator which show the following conditions: When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed. When the NUM LOCK indicator glows, the ten key allows you to enter numbers.
  • Page 53 Output Pressing FN + F5 changes the active display device. To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. Brightness Down Pressing FN + F6 decreases the computer's display panel brightness in individual steps.

  • Page 54: Using The Accupoint

    For more information, please refer to the TOSHIBA Flash Cards Help file. To access this help, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Flash Cards. In the Settings for Flash Cards window, click the Help button.

  • Page 55: Using The Fingerprint Sensor

    Strong stress is applied to the AccuPoint. If an error message appears, reboot the computer. If an error message does not appear, wait a moment for the pointer to stop, then continue operation. Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use.
  • Page 56 How to Swipe your Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible.
  • Page 57 Do not paste stickers or write on the sensor. Do not touch the sensor with a finger or any other object which may have a build-up of static electricity on it. Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition.

  • Page 58: Fingerprint Utility Limitations

    TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software.
  • Page 59 "Do you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu. Delete all users fingerprints In the TOSHIBA Fingerprint Utility main menu, click Run as administrator. User Account Control window is displayed. Click Yes.
  • Page 60 System Authentication screen is displayed. This will switch the password input screen across to the keyboard-based one. You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint Pre-Boot authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on.

  • Page 61: Optical Disc Drives

    How to Enable Fingerprint Pre-Boot authentication and Single Sign-On feature It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint Utility prior to enabling and configuring the Pre-Boot authentication and Single Sign-On feature. You should check that your fingerprint is enrolled before configuring the settings.
  • Page 62 Formats The drives support the following formats. DVD Super Multi drive The drive supports the following formats: CD-ROM, DVD-ROM, DVD- Video, CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1/Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD- EXTRA), Addressing Method 2, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL (Format1), DVD+R DL.
  • Page 63 Lay the disc, label side up, in the disc tray. Figure 4-5 Inserting a disc 1. Laser lens When the disc tray is fully opened, the edge of the computer will cover the disc tray slightly. Therefore, you will need to turn the disc at an angle when you place it in the disc tray.
  • Page 64 Writable discs This section describes the types of writable discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. CD-R discs can be written only once. The recorded data cannot be erased or changed.

  • Page 65: Writing Discs

    - this may cause you to either lose data or incur other damage to the drive or media. Disclaimer TOSHIBA does not assume responsibility for the following: Damage to any disc that may be caused by writing or rewriting with this product.
  • Page 66 Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: TAIYO YUDEN CO., Ltd.
  • Page 67 BD-RE: Panasonic Corporation BD-RE DL: Panasonic Corporation BD-R TL: TDK. SHARP BD-RE TL: Panasonic Corporation Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable. Disc created in DVD-R DL format4 (Layer Jump Recording) cannot be read.

  • Page 68: Toshiba Disc Creator

    "Disc Backup" function of TOSHIBA Disc Creator. TOSHIBA Disc Creator cannot record in packet format. You might not be able to use the "Disc Backup" function of TOSHIBA Disc Creator to back up a DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL or DVD+RW disc that was made with other software on a different optical media recorder.

  • Page 69: Toshiba Video Player

    TOSHIBA VIDEO PLAYER TOSHIBA VIDEO PLAYER is only provided with some models. Please be aware of the following limitations when you use the TOSHIBA VIDEO PLAYER: Notes on use This software can only be used on Windows operating system.
  • Page 70 Do not lock the computer using the Windows logo ( ) + L keys when running the TOSHIBA VIDEO PLAYER. The TOSHIBA VIDEO PLAYER does not have a parental control function. In order to protect copyrights, the Windows Print Screen function is disabled when TOSHIBA VIDEO PLAYER is running.

  • Page 71: Toshiba Blu-Ray Disc Player

    TOSHIBA VIDEO PLAYER features and instructions are explained in details in TOSHIBA VIDEO PLAYER Manual. Use the following procedure to open TOSHIBA VIDEO PLAYER Manual. Press the F1 key when TOSHIBA VIDEO PLAYER is launched and click the Help button. TOSHIBA Blu-ray Disc Player Please be aware of the following limitations when you use TOSHIBA Blu- ray Disc Player.

  • Page 72: Notes On Use

    When you purchase Blu-ray™ Video, make sure it matches your drive, otherwise it will not play properly. To playback video on an external display or TV using TOSHIBA Blu- ray Disc Player, use output devices like external displays or TV that have HDCP supported HDMI port.

  • Page 73: Battery

    TOSHIBA Blu-ray Disc Player features and instructions are explained in details in TOSHIBA Blu-ray Disc Player Manual. Use the following procedure to open TOSHIBA Blu-ray Disc Player Manual. Press the F1 key when TOSHIBA Blu-ray Disc Player is launched and click the Help button. Battery This section explains battery types, use, recharging methods and handling.

  • Page 74: Battery Pack

    If the RTC battery becomes completely discharged, the system will lose this information and the real time clock and calendar will stop working. You can change the Real Time Clock settings in the TOSHIBA Setup Utility. Please refer to Real Time Clock for further information.
  • Page 75 Use only the computer connected to an AC power source or optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
  • Page 76 Battery type Power off Power on RTC Battery Doesn’t charge about 10 hours (Normal) RTC Battery Doesn’t charge about 20 hours (TECRA A50-A/ Satellite PRO A50-A) (High Capacity) about 18 hours (TECRA W50-A) Please be aware that the charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you are using the computer - if you make heavy use of external devices for example, the battery might scarcely charge at all during operation.
  • Page 77 You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. This is because the computer needs this time to check the battery's remaining capacity and then calculate the remaining operating time, based on this together with the current power consumption.
  • Page 78 Battery type Sleep Mode Shut Down Mode Battery pack about 2 days about 50 days (24Wh, 3 cell) Battery pack about 5 days about 100 days (48Wh, 6 cell) Battery pack about 6 days about 135 days (TECRA A50-A/ Satellite PRO A50-A) (67Wh, 6 cell) about 80 days (TECRA W50-A) RTC Battery...

  • Page 79: Removing The Battery Pack

    The operating life of the battery pack will gradually reduce through repeated charging and discharging, and will need to be replaced when it reaches the end of its operating life. In addition to this, you might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source for an extended period of time.

  • Page 80: Wireless Wan Device

    Figure 4-7 Releasing the battery pack 1. Battery lock 3. Battery pack 2. Battery release latch Installing the battery pack To install a battery pack, follow the steps as detailed below: Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries.
  • Page 81 Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section, if required). Locate the SIM card slot. Slide your SIM card into the SIM card slot with the metal connectors facing up. Figure 4-8 Installing the SIM Card 1.

  • Page 82: Lan

    Press the SIM Card gently and release it. It pops out of the slot. Figure 4-9 Removing the SIM Card 1. SIM Card Product appearance depends on the model you purchased. Grasp the SIM Card and remove it. Install the battery pack and turn your computer over. The computer may have built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second,...

  • Page 83: Additional Memory Module

    If you are using Fast Ethernet LAN (100 megabits per second, 100BASE- TX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable.
  • Page 84 When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer. Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions.
  • Page 85 Slide your fingernail or a thin object under the cover and lift it off. Figure 4-11 Removing the memory module cover 1. Screw 2. Memory module cover Product appearance depends on the model you purchased. Follow this procedure to install or remove a memory module: Install procedure: Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side...
  • Page 86 Figure 4-12 Seating the memory module 1. Notch 3. Slot A 2. Slot B Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
  • Page 87 Please also ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in. Remove procedure: Push the latches away from the module in order to release it - a spring will force one end of the module up at an angle. And then grasp the module by its edges and remove it from the computer.
  • Page 88 Figure 4-13 Removing the memory module 1. Latches 2. Memory module Product appearance depends on the model you purchased. 8. Seat the memory module cover in place and secure it with the screw. Take care to ensure that the memory module cover is firmly closed. Figure 4-14 Seating the memory module cover 1.
  • Page 89 9. Install the battery pack - refer to Replacing the battery pack section, if required. 10. Turn your computer over. 11. Turn the computer on and make sure the available memory is recognized - to confirmed it, click Start -> Control Panel -> System and Security ->...
  • Page 90 Slip your fingernail or a thin object under the notch at the end of the keyboard brace and lift it up to release latches and remove the keyboard brace. Figure 4-16 Removing the Keyboard brace 1. keyboard brace Product appearance depends on the model you purchased. Lift the top edge of the keyboard while releasing the latches, rotate it and lay it face down on the palm rest.
  • Page 91 Loosen the screw securing the memory module cover in place - please note that the screw is attached to the cover in order to prevent it from being lost. Figure 4-17 Removing the memory module cover (1) 1. screw 2. Memory module cover Product appearance depends on the model you purchased.
  • Page 92 Figure 4-19 Installing the memory module 1. Notch 3. Slot D 2. Slot C Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
  • Page 93 Check to ensure the keyboard ribbon cables are connected to the computer when seating the keyboard. If the keyboard ribbon cables were pulled out, please contact TOSHIBA support for assistance. 14. Set the keyboard brace into its groove and hold down to secure the latches.

  • Page 94: Memory Media

    15. Close the display panel and turn the computer upside down. 16. Secure the KB screw on the underside of the computer. 17. Install the battery pack - refer to Replacing the battery pack section, if required. 18. Turn your computer over. 19.
  • Page 95 protected material on another computer or other device, and you may not reproduce any copyrighted material except for your personal enjoyment. Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards. SD, SDHC and SDXC memory cards appear the same externally. However, the logo on memory cards is different, so pay careful attention to the logo when purchasing.

  • Page 96: Inserting Memory Media

    Set the write-protect switch to the lock position, if you do not want to record data. Memory cards have a limited lifespan, so it is important to backup important data. Do not write to a card if the battery power is low. Low power could affect writing accuracy.

  • Page 97: Expresscard

    Some models are equipped with a single ExpressCard slot into which any ExpressCard device that meets industry standards, either manufactured by TOSHIBA or another vendor, can be installed. The slot supports hot plug connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps.

  • Page 98: Smart Card

    Press the ExpressCard gently to ensure a firm connection is made. Figure 4-23 Inserting the ExpressCard 1. ExpressCard slot 2. ExpressCard After inserting the ExpressCard you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct.

  • Page 99: External Display

    Inserting a Smart Card The Smart Card slot is located on the side of the computer. The Windows hot-install feature allows you to insert a Smart Card while the computer is turned on. To install a Smart Card, follow the steps as detailed below: Insert the Smart Card into the Smart Card slot with the metal connectors facing up.

  • Page 100: Connecting An External Display

    As the port operation of all external monitors have not been confirmed, some monitors may not function properly. Connecting an external display Your computer comes with a built-in display, but you can also connect other external displays via available ports on the computer. External RGB monitor port An external analog monitor can be connected to the External RGB monitor port on the computer.
  • Page 101 Plug the other end of the DisplayPort cable into the DisplayPort on your computer. Turn on the external monitor. The HDMI out port Some models are equipped with an HDMI out port. HDMI (High-Definition Multimedia Interface) port digitally transfers both video and audio data without reducing the quality.
  • Page 102 Be sure to use the function key to select the display device before starting to play video. Do not change the display device while playing video. Do not change the display device under the following conditions. While data is being read or written. While communication is being carried out.

  • Page 103: Toshiba Hi-Speed Port Replicator Iii 180W/120W

    TOSHIBA Hi-Speed Port Replicator III 180W/ 120W In addition to the ports available on the computer, the TOSHIBA Hi-Speed Port Replicator III 180W/120W also provides several kinds of ports. The Port Replicator connects directly to the docking interface on the underside of the computer.
  • Page 104 Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar and select Eject Docking Station. To access the utility, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> TOSHIBA Docking Station Utility. System sleep undocking operation will function under the following conditions: Select Do nothing for When I close the lid by clicking Start ->...

  • Page 105: Multi Monitor Support

    Some models support triple monitor or quadruple monitor function if equipped with a TOSHIBA Hi-Speed Port Replicator III 180W/120W. The port replicator supports a maximum of two external displays. For each VIDEO panel, only one port can function at a time.

  • Page 106: Security Lock

    You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer: Memory Kit DDR3 memory modules can easily be installed in the computer.

  • Page 107: Sound System And Video Mode

    TOSHIBA Hi-Speed TOSHIBA Hi-Speed Port Replicator III 180W/ Port Replicator III 120W provides several kinds of ports. Refer to 180W/120W the Port Replicator’s User's Manual for more details. Sound System and Video mode This section describes some of the audio control functions.

  • Page 108: Power Management

    DTS Studio Sound is provided with some models. It provides the following features: Advanced audio rendering to match 2D and 3D video content for enveloping surround sound Accurate placement of audio cues for immersive surround sound from any PC speaker configuration laptop / desktop speakers or headphones Broad sweet spot with elevated sound image Maximum volume output delivering maximum volume without creating...

  • Page 109: Video Mode

    Speaker Configuration Click the Auto Test button to confirm the internal speakers or the headphone sound is coming from the right direction. Default Format You can change the sample rate and bit depth of sound. Video mode Video mode settings are configured via the Screen Resolution dialog. To open the Screen Resolution dialog, click Start ->...

  • Page 110: Chapter 5 Utilities And Advanced Usage

    (such as at night), thereby reducing the load during peak periods. To access the utility, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Peak Shift Control. For more information, please refer to the Help file.
  • Page 111 This software is provided for playback of DVD PLAYER Video. To access this utility, click Start -> All Programs -> TOSHIBA -> Media & Entertainment -> TOSHIBA VIDEO PLAYER. For details on how to use TOSHIBA VIDEO PLAYER, see the help file. User's Manual...
  • Page 112 To access this utility, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> eco Utility. For details on TOSHIBA eco utility, see the help file.
  • Page 113 TOSHIBA Sleep Utility This utility is able to either enable or disable the following function: Sleep and Charge: By connecting to the USB port, devices such as digital audio players are able to charge, even when the computer is in Standby/Sleep Mode, Hibernation Mode or shutdown state.

  • Page 114: Special Features

    -> TOSHIBA -> Support & Recovery -> Applications and Drivers. Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use. Access each function using the following procedures.
  • Page 115 Intelligent power A microprocessor in the computer's intelligent power supply detects the battery's charge, supply automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor. This can be specified in the Power Options.

  • Page 116: Usb Charge

    Sleep Mode, Hibernation Mode or shutdown state. To set USB Sleep and Charge feature, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Sleep Utility. Move the slider to enable or disable the Sleep and Charge function.
  • Page 117 When Sleep and Charge function is enabled, USB bus power (DC5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC5V) is similarly supplied to the external devices which are connected to the compatible ports. However, some external devices cannot be charged solely by supplying USB bus power (DC5V).
  • Page 118 (DC5V, 1.5A) to the compatible ports while the computer is turned on. To set System ON CDP Charge Mode, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> HWSetup -> USB -> System ON CDP Charge Mode.

  • Page 119: Toshiba Password Utility

    User Password To start the utility, point to or click the following items: Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Password Utility -> User Password User authentication may be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords, etc.
  • Page 120 You can launch the BIOS setup utility to set, change or delete the HDD Password or HDD Master Password. If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE.

  • Page 121: Toshiba Hwsetup

    TOSHIBA HWSetup is the TOSHIBA configuration management tool available through the Windows operating system. To run TOSHIBA HWSetup, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> HWSetup. The TOSHIBA HWSetup window contains a number of tabs to allow specific functions of the computer to be configured.

  • Page 122: Toshiba Pc Health Monitor

    Once enabled, you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel. Doing so will automatically delete all collected information from the HDD/SSD.

  • Page 123: Using The Hard Disk Drive (Hdd) Protection

    Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started using the following methods: Click Start -> All Programs -> TOSHIBA -> Support & Recovery -> PC Health Monitor. Click the icon ( ) in the notification area, then click the "Enable PC Health Monitor..."...

  • Page 124: Toshiba Hdd Protection Properties

    You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> HDD Protection. The window can also be started from the icon on the Taskbar or from the Control Panel.

  • Page 125: Toshiba Setup Utility

    Intensely shaking the computer or other subjecting it to strong impacts may cause damage to the computer. Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
  • Page 126 You can also create recovery media and restore the system. The following items will be described in this section: System Recovery Options Creating Recovery Media Restoring the pre-installed software from your created Recovery Media Restoring the pre-installed software from the Recovery Hard Disk Drive System Recovery Options The System Recovery Options feature is installed on the hard disk when...
  • Page 127 Insert the first blank disc into the optical disc drive tray, or insert the USB Flash Memory into one available USB port. Click Start -> All Programs -> TOSHIBA -> Support & Recovery -> Recovery Media Creator. After Recovery Media Creator starts, select the type of media and the title you wish to copy, and then click the Create button.

  • Page 128: Recovery Hard Disk Drive

    Recovery Media. However, if you have already created a "Recovery Media", you can use it to restore the recovery partition. If you have not created "Recovery Media", please contact TOSHIBA support for assistance. Restoring the pre-installed software from the...
  • Page 129 Ordering Recovery Discs from TOSHIBA* You can order Product Recovery discs for your notebook from the TOSHIBA Europe Backup Media Online Shop. * Please note that this service is not free-of-charge. Visit https://backupmedia.toshiba.eu on the Internet. Follow the on-screen instructions. You will receive your Recovery Discs within two weeks after placing your order.

  • Page 130: Troubleshooting

    In reality many problems can be solved simply, but a few may require help from TOSHIBA Support - if you find you need to consult others, be prepared to describe the problem in as much detail as possible.

  • Page 131: Analyzing The Problem

    Always try to make detailed notes of your observations and keep them in a permanent error log - this will help you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made will help to identify the problem faster.
  • Page 132 Before using a peripheral device or application software that is not an authorized TOSHIBA part or product, make sure the device or software can be used with your computer. Use of incompatible devices may cause injury or may damage your computer.

  • Page 133: Hardware And System Checklist

    Computer shuts Leave the computer off until the it reaches room down automatically. temperature. If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact TOSHIBA Support. User's Manual...

  • Page 134: Ac Power

    If the AC adaptor still does not power the computer, you should contact TOSHIBA Support. Battery If you suspect a problem with the battery, you should check the status of the DC IN/Battery indicator.
  • Page 135 However, if you do not believe the battery is at the end of its operating life, you should speak to TOSHIBA Support. Battery doesn’t If you frequently recharge a partially charged...

  • Page 136: Real Time Clock

    - you will need to set the date and time time are lost. in the TOSHIBA Setup Utility by using the following steps: Press and hold the F2 key, and then turn on the computer - the TOSHIBA Setup Utility will load.
  • Page 137 As a last resort you should reformat the HDD/SSD and then reload the operating system and all other files and data. If you are still unable to resolve the problem, contact TOSHIBA Support. Optical Disc Drive For further information, please refer to Operating Basics.
  • Page 138 If you are still unable to resolve the problem, contact TOSHIBA Support. Pointing device If you are using a USB mouse, you should also refer to both the mouse section and the documentation supplied with your mouse.

  • Page 139: Usb Mouse

    To access it, click Start -> Control Panel -> too sensitive or not Hardware and Sound -> Mouse. sensitive enough. If you are still unable to resolve the problem, contact TOSHIBA Support. USB mouse Problem Procedure On-screen pointer In this instance the system might be busy - Try...

  • Page 140: Usb Device

    If you are still unable to resolve the problem, contact TOSHIBA Support. USB device In addition to the information in this section, please also refer to the documentation supplied with your USB device.
  • Page 141 Sleep and Charge Enable the Sleep and Charge function in the function. TOSHIBA System Settings. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons.

  • Page 142: Sound System

    Volume cannot be adjusted during Windows start up or shut down. If you are still unable to resolve the problem, contact TOSHIBA Support. External monitor Please also refer to Operating Basics, and to the documentation supplied with your monitor for further information.
  • Page 143 Display error occurs Check that the cable connecting the external monitor to the computer is firmly attached. If you are still unable to resolve the problem, contact TOSHIBA Support. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub.

  • Page 144: Toshiba Support

    TOSHIBA Support. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first.
  • Page 145 TOSHIBA technical support If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the location listed in the enclosed warranty booklet or visit www.toshiba-europe.com on the Internet.. User's Manual...

  • Page 146: Appendix Specifications

    Chapter 7 Appendix Specifications This section summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased. Size Approximately 380.9 (w) x 253.9 (d) x 27.8/34.9 (h) millimeters (not including parts that extend beyond the main body).

  • Page 147: Ac Power Cord And Connectors

    External RGB monitor port pin assignment Signal Name Description Red Video Signal Green Video Signal Blue Video Signal Reserved Reserved Ground Ground Ground Ground Power Supply Ground Reserved Reserved Data Signal HSYNC Horizontal Sync Signal VSYNC Vertical Sync Signal Data Clock Signal I/O (I): Input to computer I/O (O): Output from computer AC Power Cord and Connectors...
  • Page 148 Certification agencies China: U.S. and Canada: UL listed and CSA certified No. 18 AWG, Type SVT or SPT-2 Australia: Japan: DENANHO Europe: Austria: Italy: Belgium: CEBEC The Netherlands: KEMA Denmark: DEMKO Norway: NEMKO Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or...

  • Page 149: Information For Wireless Devices

    Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.11 Standard on Wireless LANs (Revision a/b/g/n or b/g/ n), as defined and approved by the Institute of Electrical and...
  • Page 150 Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Module. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.htm Wireless Devices and your health Wireless products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
  • Page 151 TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Card Specifications...
  • Page 152 You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other. Bluetooth Stack for Windows by TOSHIBA Please note that this software is specifically designed for the following operating systems:...
  • Page 153 This Bluetooth Stack is based on the Bluetooth specification, depending on the model you purchased. However, TOSHIBA cannot confirm the compatibility between any computing products and/or other electronic devices that use Bluetooth, other than TOSHIBA notebook computers. Release Notes related to the Bluetooth Stack for Windows...
  • Page 154 Norway: Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Alesund. Russian Only for indoor applications. Federation: Restrictions for Use of 5150-5350MHz Frequencies in Europe Italy: For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises.
  • Page 155 Russian Limited e.i.r.p 100mW. Permitted to use Federation: only for indoor applications, closed industrial and warehouse areas, and on board aircraft. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight.
  • Page 156 The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 157 If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations.
  • Page 158 2.4 : This equipment uses a frequency of 2.4GHz. DS : This equipment uses DS-SS modulation. OF : This equipment uses OFDM modulation. 4 : The interference range of this equipment is less than 40m. : This equipment uses a frequency bandwidth from 2,400MHz to 2,483.5MHz.

  • Page 159: Legal Footnotes

    This equipment is approved to the radio standard by the countries/regions in the following table. If you use this equipment in the countries/regions which are not listed in the table blow, please contact TOSHIBA Support. As of August 2013 Austria...
  • Page 160 (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - contact TOSHIBA support for details). CPU performance may also vary from specifications due to design configuration.

  • Page 161: Battery Life

    Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.

  • Page 162: Glossary

    be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content. Actual formatted capacity may vary. Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate.
  • Page 163 ASCII: American Standard Code for Information Interchange BIOS: Basic Input/output System BD-ROM: Blu-ray Disc Read-only Memory bps: bits per second Compact Disc CD-ROM: Compact Disc Read-only Memory CD-RW: Compact Disc-rewritable CMOS: Complementary Metal-oxide Semiconductor CPU: Central Processing Unit Direct Current DDR: Double Data Rate DIMM:...
  • Page 164 ISP: Internet Service Provider kilobyte LAN: Local Area Network LCD: Liquid Crystal Display LED: Light Emitting Diode megabyte MBps: megabytes per second MMC: Multi Media Card OCR: Optical Character Recognition (Reader) Personal Computer PCI: Peripheral Component Interconnect PCMCIA: Personal Computer Memory Card International Association RAM: Random Access Memory...

  • Page 165: Index

    4-28 removing 4-48 Bluetooth External monitor Bluetooth Stack for problems 6-14 Windows by Toshiba 5-3 FN + 1 ( reduce) 4-3 Cleaning the computer 1-17 FN + 2 (enlarge) 4-3 Cooling vents 3-3, 3-8 FN + 3 (Volume down) 4-3...
  • Page 166 FN + F3 (Sleep) 4-2 FN + F4 (Hibernate) 4-2 Media care FN + F5 (Output) 4-3 Card care 4-45 Memory card care 4-46 FN + F6 (Brightness Down) Memory FN + F7 (Brightness Up) 4-3 installing 4-30, 4-34, 4-39 removing 4-31 FN + F8 (Wireless) 4-3 FN + F9 (Touch Pad) 4-3...
  • Page 167 AC power 6-5 problems 6-13 Analyzing the problem 6-2 Battery 6-5 Dual Pointing device 6-9 External monitor 6-13 Hardware and system TOSHIBA Disc Creator 4-18 checklist 6-4 HDD 6-8 TOSHIBA HDD/SSD Alert Internal display panel 6-7 Utility 5-3 Keyboard 6-7...

This manual is also suitable for:

A50-asmbnx2A50-asmbn03A50-asmbn22Tecra a50-aTecra w50-aSatellite pro a50-a

Table of Contents